scholarly journals Intelligent Active Force Control Of A Twin Rotor System

2020 ◽  
Vol 884 ◽  
pp. 012102
Author(s):  
Y S Tay ◽  
M Mailah ◽  
H H Tang
Keyword(s):  
Force Control ◽  
Rotor System ◽  
Active Force ◽  
Active Force Control ◽  
Twin Rotor

Adaptive Active Force Control Application to Twin Rotor Mimo System

2013 ◽  
Vol 393 ◽  
pp. 688-693 ◽  
Author(s):  
Hanif Ramli ◽  
Wahyu Kuntjoro ◽  
M.S. Meon ◽  
K.M Asraf K. Ishak
Keyword(s):  
Force Control ◽  
Control Algorithm ◽  
Mimo System ◽  
Active Force ◽  
Optimum Control ◽  
Active Force Control ◽  
Non Linear ◽  
Artificial Neural Network Ann ◽  
Twin Rotor Mimo System ◽  
Twin Rotor

This paper reports a current study on modeling and simulation of adaptive Active Force Control (AFC) based scheme embedded with an artificial neural network (ANN) and/or fuzzy logic (FL) in response manipulations of the twin rotor multi-input multi-output (MIMO) system (TRMS). TRMS is well known for its non-linear behaviour and common classical control scheme such as Proportional-Integral-Derivative (PID) would not be adequate to compensate disturbances. The disturbances in this case were as the results of non-linear external and internal parametric changes, namely angular momentum and couple reactions between the two axes of TRMS. The adaptive control algorithm was proposed in both pitch and yaw to generate an optimum control gain for both responses, simulated viz. MATLAB/SIMULINK software Package. The ANN and FL were integrated into the scheme and act as optimum control algorithm in catalyzing the performance of the TRMS. The results from hybrid conditions of PID-AFC, PID-AFC-ANN and PID-AFC-FL respectively were observed and analyzed. From performance evaluation, PID-AFC-FL scheme has demonstrated a potentially robust and effective manipulating capability in trajectory tracking.

scholarly journals Knowledge-Based Trajectory Error Pattern Method Applied to an Active Force Control Scheme

1970 ◽  
Vol 3 (1) ◽  
Author(s):  
Endra Pitowarno, Musa Mailah, Hishamuddin Jamaluddin
Keyword(s):  
Force Control ◽  
Error Pattern ◽  
Robot Arm ◽  
Active Force ◽  
Trajectory Error ◽  
Track Error ◽  
Knowledge Based ◽  
Inertia Matrix ◽  
Active Force Control ◽  
Control Scheme

The active force control (AFC) method is known as a robust control scheme that dramatically enhances the performance of a robot arm particularly in compensating the disturbance effects. The main task of the AFC method is to estimate the inertia matrix in the feedback loop to provide the correct (motor) torque required to cancel out these disturbances. Several intelligent control schemes have already been introduced to enhance the estimation methods of acquiring the inertia matrix such as those using neural network, iterative learning and fuzzy logic. In this paper, we propose an alternative scheme called Knowledge-Based Trajectory Error Pattern Method (KBTEPM) to suppress the trajectory track error of the AFC scheme. The knowledge is developed from the trajectory track error characteristic based on the previous experimental results of the crude approximation method. It produces a unique, new and desirable error pattern when a trajectory command is forced. An experimental study was performed using simulation work on the AFC scheme with KBTEPM applied to a two-planar manipulator in which a set of rule-based algorithm is derived. A number of previous AFC schemes are also reviewed as benchmark. The simulation results show that the AFC-KBTEPM scheme successfully reduces the trajectory track error significantly even in the presence of the introduced disturbances.Key Words:  Active force control, estimated inertia matrix, robot arm, trajectory error pattern, knowledge-based.

Intelligent Adaptive Active Force Control of a Robotic Arm with Embedded Iterative Learning Algorithms

2012 ◽  
Author(s):  
Musa Mailah ◽  
Miaw Yong Ong
Keyword(s):  
Force Control ◽  
Learning Algorithms ◽  
Iterative Learning ◽  
Operating Conditions ◽  
Robotic Arm ◽  
Active Force ◽  
Inertia Matrix ◽  
Active Force Control ◽  
Controller Gain ◽  
On Line

Kawalan jitu dan lasak bagi satu sistem lengan robot atau pengolah adalah amat penting terutama sekali jika sistem mengalami pelbagai bentuk bebanan dan keadaan pengendalian. Kertas kerja ini memaparkan satu kaedah baru dan lasak untuk mengawal lengan robot menggunakan teknik pembelajaran secara berlelaran yang dimuatkan dalam strategi kawalan daya aktif. Sebanyak dua algoritma pembelajaran utama digunakan dalam kajian – yang pertama digunakan untuk menala gandaan pengawal secara automatik manakala yang satu lagi pula untuk menganggarkan matriks inersia pengolah. Kedua-dua parameter ini dihasilkan secara adaptif dan dalam talian ketika robot sedang menjalankan tugas menjejak trajektori dalam persekitaran tindakan daya gangguan. Dalam kajian ini, pengetahuan awal tentang kedua–dua nilai gandaan pengawal dan anggaran matriks inersia tidak wujud. Dengan demikian, suatu skema kawalan yang jitu dan lasak terhasil. Keberkesanan kaedah yang dicadangkan dapat ditentusahkan melalui hasil kajian yang diperoleh dan dibentangkan dalam kertas kerja ini. Kata kunci: Adaptif; kawalan daya aktif; pembelajaran berlelaran; matriks inersia; gandaan pengawal The robust and accurate control of a robotic arm or manipulator are of prime importance especially if the system is subjected to varying forms of loading and operating conditions. The paper highlights a novel and robust method to control a robotic arm using an iterative learning technique embedded in an active force control strategy. Two main iterative learning algorithms are utilized in the study – the first is used to automatically tune the controller gains while the second to estimate the inertia matrix of the manipulator. These parameters are adaptively computed on-line while the robot is executing a trajectory tracking task and subject to some forms of external disturbances. No priori knowledge of both the controller gains and the estimated inertia matrix are ever assumed in the study. In this way, an adaptive and robust control scheme is derived. The effectiveness of the method is verified and can be seen from the results of the work presented in this paper. Keywords: Adaptive; active force control; iterative learning; inertia matrix; controller gain

scholarly journals Stability Analysis of a Linear Friction-Induced Vibration Model and Its Prevention Using Active Force Control

2014 ◽  
Vol 6 ◽  
pp. 251594 ◽  
Author(s):  
S. M. Hashemi-Dehkordi ◽  
A. R. Abu-Bakar ◽  
M. Mailah
Keyword(s):  
Force Control ◽  
Pid Controller ◽  
Active Force ◽  
Active Force Control ◽  
Vibration Model ◽  
Control Scheme ◽  
Linear Friction ◽  
Critical Slope ◽  
Negative Damping ◽  
Friction Induced Vibration

This paper presents friction-induced vibration (FIV) caused by combined mode-coupling and negative damping effects in a simple FIV model. In doing so, a new four-degree-of-freedom linear model which consists of a slider and a block is proposed and then simulated using MATLAB/Simulink. Stability or instability of the FIV model is defined by the convergence or divergence of time domain responses of the slider and the block. Having found critical slope of friction-velocity characteristics that generate instabilities in the model, a conventional closed loop proportional-integral-derivative (PID) controller is first introduced into the main model in order to attenuate the vibration level and subsequently to suppress it. Later, the model is integrated with the active force control (AFC) element to effectively reject the disturbance and reduce the vibrations. It is found that the integrated PID-AFC scheme is effective in reducing vibration compared to the pure PID controller alone. Thus, the proposed control scheme can be one of the potential solutions to suppress vibration in a friction-induced vibration system.

scholarly journals Robust Motion Control for Mobile Manipulator Using Resolved Acceleration and Proportional-Integral Active Force Control

10.5772/5794 ◽  
2005 ◽  
Vol 2 (2) ◽  
pp. 14 ◽  
Author(s):  
Musa Mailah ◽  
Endra Pitowarno ◽  
Hishamuddin Jamaluddin
Keyword(s):  
Motion Control ◽  
Force Control ◽  
Dynamic Control ◽  
Mobile Manipulator ◽  
Active Force ◽  
Proportional Integral ◽  
Active Force Control ◽  
Resolved Acceleration Control ◽  
Unknown Disturbances ◽  
Robust Motion Control

A resolved acceleration control (RAC) and proportional-integral active force control (PIAFC) is proposed as an approach for the robust motion control of a mobile manipulator (MM) comprising a differentially driven wheeled mobile platform with a two-link planar arm mounted on top of the platform. The study emphasizes on the integrated kinematic and dynamic control strategy in which the RAC is used to manipulate the kinematic component while the PIAFC is implemented to compensate the dynamic effects including the bounded known/unknown disturbances and uncertainties. The effectivenss and robustness of the proposed scheme are investigated through a rigorous simulation study and later complemented with experimental results obtained through a number of experiments performed on a fully developed working prototype in a laboratory environment. A number of disturbances in the form of vibratory and impact forces are deliberately introduced into the system to evaluate the system performances. The investigation clearly demonstrates the extreme robustness feature of the proposed control scheme compared to other systems considered in the study.

Sign in / Sign up

Export Citation Format

Share Document