scholarly journals The performance of solar cells using chlorophyll dye from Syzygium paniculatum

Clean Energy ◽  
2021 ◽  
Vol 5 (3) ◽  
pp. 433-440
Author(s):  
Sri Wuryanti
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Irregular Shapes ◽  
Sensitized Solar Cells

Abstract In this study, analysis was performed of the macro characterization of solar cells with chlorophyll dye from Syzygium paniculatum, using scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) analysis. Solar cells based on titanium dioxide (TiO2) nanomaterial and chlorophyll dye from S. paniculatum can increase efficiency due to flavonoids and batulinic acid content. Photoanode TiO2 is one of the essential factors determining the photovoltaic properties of dye-sensitized solar cells (DSSCs) and shade, which broadens the absorption spectrum. Furthermore, the method used in this research involved varying the colour of the S. paniculatum leaves, namely red (SP-Red), green (SP-Green) and a red–green mix (SP-Mix). From a macro analysis, SEM observations resulted in agglomerated and aggregated TiO2-polyethylene glycol (PEG)-dye layers with irregular shapes. EDX observation resulted in a peak in Ti at 5 keV and all constituents were detected with an O:Ti ratio of 3.47:1 for FTO-TiO2/PEG using SP-Green. Measurement of voltage-current (IV) using a digital multimeter indicated that the best occurred in the DSSC with SP-Green, resulting in a short-circuit current density (Isc) of 0.0047 mA/cm2, an open-circuit voltage (Voc) of 0.432 V, a charging factor (FF) of 0.749 and an efficiency (η) of 3.724%.

Preparation and Photovoltaic Properties of Flexible Dye-Sensitized Solar Cells

2011 ◽  
Vol 306-307 ◽  
pp. 112-115 ◽  
Author(s):  
You Zeng ◽  
Li Jia Zhao ◽  
Ying Zhen ◽  
Fang Xiao Shi ◽  
Yu Tong
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Treatment Temperature ◽  
Photovoltaic Properties ◽  
Dye Sensitized ◽  
Conductive Glass ◽  
Sensitized Solar Cells

Flexible dye-sensitized solar cells (DSCs) were prepared by using carbon nanotube transparent conductive films (CNT-TCFs) as flexible substrates, and their photovoltaic properties were investigated as well. The flexible DSCs show typical photovoltaic characteristics with short-circuit current of 0.78 μA and open-circuit voltage of 1.48 mV, which was strongly influenced by heat-treatment temperature, type of dyes, and electrical resistivity. In light of their lighter weight and higher flexibility than conventional DSCs based on conductive glass substrates, the flexible DSCs have great potential as functional photoelectric components in many fields.

Approach to tune short-circuit current and open-circuit voltage of dye-sensitized solar cells: π-linker modification and photoanode selection

RSC Advances ◽  
2014 ◽  
Vol 4 (80) ◽  
pp. 42252-42259 ◽  
Author(s):  
Shengbo Zhu ◽  
Zhongwei An ◽  
Xinbing Chen ◽  
Pei Chen ◽  
Qianfeng Liu
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

The modification of the π-linker of cyclic thiourea functionalized dyes has a significant effect on the short-circuit current density and open-circuit voltage of dye-sensitized solar cells.

scholarly journals Electrolyte tuning in dye-sensitized solar cells with N-heterocyclic carbene (NHC) iron(II) sensitizers

2018 ◽  
Vol 9 ◽  
pp. 3069-3078 ◽  
Author(s):  
Mariia Karpacheva ◽  
Catherine E Housecroft ◽  
Edwin C Constable
Keyword(s):  
Ionic Liquid ◽  
Solar Cells ◽  
Electrochemical Impedance ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

We demonstrate that the performances of dye-sensitized solar cells (DSCs) sensitized with a previously reported N-heterocyclic carbene iron(II) dye in the presence of chenodeoxycholic acid co-adsorbant, can be considerably improved by altering the composition of the electrolyte while retaining an I−/I3 − redox shuttle. Critical factors are the solvent, presence of ionic liquid, and the use of the additives 1-methylbenzimidazole (MBI) and 4-tert-butylpyridine (TBP). For the electrolyte solvent, 3-methoxypropionitrile (MPN) is preferable to acetonitrile, leading to a higher short-circuit current density (J SC) with little change in the open-circuit voltage (V OC). For electrolytes containing MPN, an ionic liquid and MBI (0.5 M), DSC performance depended on the ionic liquid with 1-ethyl-3-methylimidazolium hexafluoridophosphate (EMIMPF) > 1,2-dimethyl-3-propylimidazolium iodide (DMPII) > 1-butyl-3-methylimidazolium iodide (BMII) ≈ 1-butyl-3-methylimidazolium hexafluoridophosphate (BMIMPF). Omitting the MBI leads to a significant improvement in J SC when the ionic liquid is DMPII, BMII or BMIMPF, but with EMIMPF the removal of the MBI additive results in a dramatic decrease in V OC (542 to 42 mV). For electrolytes containing MPN and DMPII, the effects of altering the MBI concentration have also been investigated. Although the addition of TBP improves V OC, it causes significant decreases in J SC. The best performing DSCs with the NHC-iron(II) dye employ an I−/I3 −-based electrolyte with MPN as solvent, DMPII ionic liquid (0.6 M) with no or 0.01 M MBI; values of J SC = 2.31 to 2.78 mA cm−2, V OC = 292 to 374 mV have been achieved giving η in the range of 0.47 to 0.57% which represents 7.8 to 9.3% relative to an N719 reference DSC set at 100%. Electrochemical impedance spectroscopy has been used to understand the role of the MBI additive in the electrolytes.

Aero-Sol-Gel Synthesis of Mesoporous TiO2 Nanoparticles and Their Photovoltaic Properties in Dye-Sensitized Solar Cells

2012 ◽  
Vol 1442 ◽  
Author(s):  
Ji Young Ahn ◽  
Kook Joo Moon ◽  
Ji Hoon Kim ◽  
Soo Hyung Kim
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Sol Gel ◽  
Photovoltaic Performance ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Photovoltaic Properties ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

ABSTRACTHighly mesoporous TiO2 nanoparticles (NPs) were synthesized by an aero-sol-gel process in this approach. By varying the mass fraction of inorganic templates, the formation of mesoporous TiO2 NPs with optimized surface area and pore volume distributions was examined. Then, the photovoltaic properties of the resulting mesoporous TiO2 NPs were systematically investigated by applying them into the photoanode of dye-sensitized solar cells (DSSCs). The mesoporous TiO2 NP-based DSSCs fabricated in this study showed an improved short circuit current density and power conversion efficiency compared with solid TiO2 NP-based DSSCs due to the increase of the amount of inorganic dye (N719) adsorption in the mesoporous TiO2 NPs. These mesoporous TiO2 NPs fabricated have a strong potential as an effective dye supporting and electron transfer medium to improve the photovoltaic performance of DSSCs.

IMPROVING STABILITY OF CHLOROPHYLL AS NATURAL DYE FOR DYE-SENSITIZED SOLAR CELLS

2017 ◽  
Vol 80 (1) ◽  
Author(s):  
Zainal Arifin ◽  
Sudjito Soeparman ◽  
Denny Widhiyanuriyawan ◽  
Suyitno Suyitno ◽  
Argatya Tara Setyaji
Keyword(s):  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Natural Dyes ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Natural dyes have attracted much researcher’s attention due to their low-cost production, simple synthesis processes and high natural abundance. However the dye-sensitized solar cells (DSSCs) based natural dyes have higher tendency to degradation. This article reports on the enhancement of performance and stability of dye-sensitized solar cells (DSSCs) using natural dyes. The natural dyes were extracted from papaya leaves by ethanol solvent at a temperature of 50 °C. Then the extracted dyes were isolated and modified into Mg-chlorophyll using column chromatography. Mg-chlorophyll was then synthesized into Fe-chlorophyll to improve stability. The natural dyes were characterized using ultraviolet-visible spectrometry, Fourier transform infrared spectroscopy, and cyclic voltammetry. The performance of DSSCs was tested using a solar simulator. The results showed the open-circuit voltage, the short-circuit current density, and the efficiency of the extracted papaya leaves-based DSSCs to be 325 mV, 0.36 mA/cm2, and 0.07%, respectively. Furthermore, the DSSCs with purified chlorophyll provide high open-circuit voltage of 425 mV and short-circuit current density of 0.45 mA/cm2. The use of Fe-chlorophyll for sensitizing the DSSCs increases the efficiency up to 2.5 times and the stability up to two times. The DSSCs with Fe-chlorophyll dyes provide open-circuit voltage, short-circuit current density, and efficiency of 500 mV, 0.62 mA/cm2, and 0.16%, respectively. Further studies to improve the current density and stability of natural dye-based DSSCs along with an improvement in the anchor between dyes and semiconducting layers are required.

scholarly journals Effects of Different Doping Ratio of Cu Doped CdS on QDSCs Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-4
Author(s):  
Xiaojun Zhu ◽  
Xiaoping Zou ◽  
Hongquan Zhou
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Sensitized Solar Cells ◽  
Doping Ratio

We use the successive ionic layer adsorption and reaction (SILAR) method for the preparation of quantum dot sensitized solar cells, to improve the performance of solar cells by doping quantum dots. We tested the UV-Vis absorption spectrum of undoped CdS QDSCs and Cu doped CdS QDSCs with different doping ratios. The doping ratios of copper were 1 : 100, 1 : 500, and 1 : 1000, respectively. The experimental results show that, under the same SILAR cycle number, Cu doped CdS quantum dot sensitized solar cells have higher open circuit voltage, short circuit current density photoelectric conversion efficiency than undoped CdS quantum dots sensitized solar cells. Refinement of Cu doping ratio are 1 : 10, 1 : 100, 1 : 200, 1 : 500, and 1 : 1000. When the proportion of Cu and CdS is 1 : 10, all the parameters of the QDSCs reach the minimum value, and, with the decrease of the proportion, the short circuit current density, open circuit voltage, and the photoelectric conversion efficiency are all increased. When proportion is 1 : 500, all parameters reach the maximum values. While with further reduction of the doping ratio of Cu, the parameters of QDSCs have a decline tendency. The results showed that, in a certain range, the lower the doping ratio of Cu, the better the performance of quantum dot sensitized solar cell.

scholarly journals Prunus domestica dye extraction for fabrication of zinc oxide based dye-sensitized solar cells

BIBECHANA ◽  
2015 ◽  
Vol 13 ◽  
pp. 23-28
Author(s):  
Leela Pradhan Joshi
Keyword(s):  
Zinc Oxide ◽  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Zinc Nitrate ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Dye Extraction ◽  
Sensitized Solar Cells

Aluminium doped Zinc Oxide (AZO) seed layers were deposited on Fluorine doped Tin Oxide (FTO) substrates using a spin coating technique. These were then immersed in growth solutions of zinc nitrate, hexamethylenetetramine and distilled water to develop nanoplates of Zinc Oxide (ZnO). The nanostructures of ZnO grown on FTO were studied using x-ray diffraction techniques. Dye-sensitized solar cells (DSSC) were fabricated using two prepared electrodes, one of dye-loaded zinc oxide and another that was platinum coated. The electrolyte used was potassium iodide iodine solution. The performance of the assembled DSCCs was tested by drawing an IV curve. The results showed that the short circuit current and open circuit voltages were about 10 microamperes and 270 millivolts respectively.BIBECHANA 13 (2016) 23-28

scholarly journals There Is a Future for N-Heterocyclic Carbene Iron(II) Dyes in Dye-Sensitized Solar Cells: Improving Performance through Changes in the Electrolyte

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4181 ◽  
Author(s):  
Mariia Karpacheva ◽  
Vanessa Wyss ◽  
Catherine E. Housecroft ◽  
Edwin C. Constable
Keyword(s):  
Solar Cells ◽  
Alkyl Chain ◽  
Electrochemical Impedance ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Ion Concentration ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

By systematic tuning of the components of the electrolyte, the performances of dye-sensitized solar cells (DSCs) with an N-heterocyclic carbene iron(II) dye have been significantly improved. The beneficial effects of an increased Li+ ion concentration in the electrolyte lead to photoconversion efficiencies (PCEs) up to 0.66% for fully masked cells (representing 11.8% relative to 100% set for N719) and an external quantum efficiency maximum (EQEmax) up to approximately 25% due to an increased short-circuit current density (JSC). A study of the effects of varying the length of the alkyl chain in 1-alkyl-3-methylimidazolium iodide ionic liquids (ILs) shows that a longer chain results in an increase in JSC with an overall efficiency up to 0.61% (10.9% relative to N719 set at 100%) on going from n-methyl to n-butyl chain, although an n-hexyl chain leads to no further gain in PCE. The results of electrochemical impedance spectroscopy (EIS) support the trends in JSC and open-circuit voltage (VOC) parameters. A change in the counterion from I− to [BF4]− for 1-propyl-3-methylimidazolium iodide ionic liquid leads to DSCs with a remarkably high JSC value for an N-heterocyclic carbene iron(II) dye of 4.90 mA cm−2, but a low VOC of 244 mV. Our investigations have shown that an increased concentration of Li+ in combination with an optimized alkyl chain length in the 1-alkyl-3-methylimidazolium iodide IL in the electrolyte leads to iron(II)-sensitized DSC performances comparable with those of containing some copper(I)-based dyes.

Synthesis and Dye-sensitized Solar Cell Application of Polyolefinic Aromatic Molecules with Pyrene as Surface Group

2011 ◽  
Vol 64 (7) ◽  
pp. 951 ◽  
Author(s):  
Perumal Rajakumar ◽  
Kathiresan Visalakshi ◽  
Shanmugam Ganesan ◽  
Pichai Maruthamuthu ◽  
Samuel Austin Suthanthiraraj
Keyword(s):  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Surface Group ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Solar Cell Application ◽  
Aromatic Molecules ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Synthesis of polyolefinic aromatic molecules with pyrene as the surface group, and their role as an additive in the redox couple of dye-sensitized solar cells, is described. The studies yield a promising power conversion efficiency of 5.27% with a short circuit current density of 6.50 mA cm–2, an open circuit voltage of 0.60 V, and a fill factor of 0.54 under 40 mW cm–2 simulated air mass (A.M.) 1.5 illumination. Most importantly, the photocurrent responsivity increases with an increase in the number of pyrene units on the surface.

Sign in / Sign up

Export Citation Format

Share Document