Numerical study of boundary layer transition using intermittency model

2019 ◽  
Vol 91 (8) ◽  
pp. 1156-1168 ◽  
Author(s):  
Massoud Tatar ◽  
Mojtaba Tahani ◽  
Mehran Masdari

Purpose In this paper, the applicability of shear stress transport k-ω model along with the intermittency concept has been investigated over pitching airfoils to capture the laminar separation bubble (LSB) position and the boundary layer transition movement. The effect of reduced frequency of oscillations on boundary layer response is also examined. Design/methodology/approach A two-dimensional computational fluid dynamic code was developed to compute the effects of unsteadiness on LSB formation, transition point movement, pressure distribution and lift force over an oscillating airfoil using transport equation of intermittency accompanied by the k-ω model. Findings The results indicate that increasing the angle of attack over the stationary airfoil causes the LSB size to shorten, leading to a rise in wall shear stress and pressure suction peak. In unsteady cases, both three- and four-equation models are capable of capturing the experimentally measured transition point well. The transition is delayed for an unsteady boundary layer in comparison with that for a static airfoil at the same angle of attack. Increasing the unsteadiness of flow, i.e. reduced frequency, moves the transition point toward the trailing edge of the airfoil. This increment also results in lower static pressure suction peak and hence lower lift produced by the airfoil. It was also found that the fully turbulent k-ω shear–stress transport (SST) model cannot capture the so-called figure-of-eight region in lift coefficient and the employment of intermittency transport equation is essential. Practical implications Boundary layer transition and unsteady flow characteristics owing to airfoil motion are both important for many engineering applications including micro air vehicles as well as helicopter blade, wind turbine and aircraft maneuvers. In this paper, the accuracy of transition modeling based on intermittency transport concept and the response of boundary layer to unsteadiness are investigated. Originality/value As a conclusion, the contribution of this paper is to assess the ability of intermittency transport models to predict LSB and transition point movements, static pressure distribution and aerodynamic lift variations and boundary layer flow pattern over dynamic pitching airfoils with regard to oscillation frequency effects for engineering problems.

2020 ◽  
Vol 92 (4) ◽  
pp. 611-620
Author(s):  
Ryszard Szwaba ◽  
Piotr Kaczyński ◽  
Piotr Doerffer

Purpose The purpose of this paper is to study experimentally the effect of transition and also the roughness height on the flow structure of the shock wave boundary layer interaction in the blades passage of a compressor cascade. Design/methodology/approach A model of a turbine compressor passage was designed and assembled in a transonic wind tunnel. In the experiment, the distributed roughness with different heights and locations was used to induce transition upstream of the shock wave. Findings Recommendation regarding the roughness parameters for the application depends on what is more important as goal, whether the reduction of losses or unsteadiness. In case if more important are the losses reduction, a good choice for the roughness location seems to be the one close to the shock wave position. Research limitations/implications The knowledge gained by this paper will enable the implementation of an effective laminar flow technology for engines in which the interaction of a laminar boundary layer with a shock wave takes place in the propulsion system and causes severe problems. Originality/value The paper focuses on the influence of the boundary layer transition induced by different roughness values and locations on aerodynamic performance of a compressor cascade. Very valuable results were obtained in the roughness application for the boundary layer transition control, demonstrating a positive effect in changing the nature of the interaction and also some negative influence in case of oversized roughness height, which cannot be found in the existing literature.


1988 ◽  
Vol 92 (912) ◽  
pp. 63-68 ◽  
Author(s):  
P. E. Roach ◽  
J. T. Turner

Summary Experiments have been performed to study the influence of multiple surface static pressure tappings on transition of the boundary layer on a circular cylinder in cross-flow. A wide range of tapping and cylinder dimensions have been examined to demonstrate that the tappings can act in the same way as trip wires or other surface roughness to reduce the Reynolds number at which transition occurs. Hence, the pressure distribution around the cylinder may be influenced by the presence of the tappings, leading to incorrect measurements. Examination of the data has resulted in a correlation which should make it possible to avoid this tapping/boundary layer interaction in future experiments involving similar cylindrical bodies.


1994 ◽  
Vol 14 (Supplement1) ◽  
pp. 115-118
Author(s):  
Masayoshi Noguchi ◽  
Norikazu Sudani ◽  
Yoji Ishida ◽  
Mamoru Sato ◽  
Hiroshi Kanda

2016 ◽  
Vol 2016 ◽  
pp. 1-14 ◽  
Author(s):  
Natalie R. Smith ◽  
Nicole L. Key

The stator inlet flow field in a multistage compressor varies in the pitchwise direction due to upstream vane wakes and how those wakes interact with the upstream rotor tip leakage flows. If successive vane rows have the same count, then vane clocking can be used to position the downstream vane in the optimum circumferential position for minimum vane loss. This paper explores vane clocking effects on the suction side vane boundary layer development by measuring the quasi-wall shear stress on the downstream vane at three spanwise locations. Comparisons between the boundary layer transition on Stator 1 and Stator 2 are made to emphasize the impact of rotor-rotor interactions which are not present for Stator 1 and yet contribute significantly to transition on Stator 2. Vane clocking can move the boundary layer transition in the path between the wakes by up to 24% of the suction side length at midspan by altering the influence of the Rotor 1 wakes in the 3/rev modulation from rotor-rotor interactions. The boundary layer near the vane hub and tip experiences earlier transition and separation due to interactions with the secondary flows along the shrouded endwalls. Flow visualization and Stator 2 wakes support the shear stress results.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Peng Lin ◽  
Xueqiang Liu ◽  
Neng Xiong ◽  
Xiaobing Wang ◽  
Ma Shang ◽  
...  

AbstractWith the aim for a low-aspect-ratio flying wing configuration, this study explores the influence of wall temperature gradient on the laminar and turbulent boundary layers of aircraft surface and determines the effect on the transition Reynolds number and wall friction drag. A four-equation turbulence model with transition mode is used to numerically simulate the flow around the model. The variation of wall friction coefficient, transition Reynolds number, and turbulent boundary layer flow with wall temperature are emphatically investigated. Results show that when the wall temperature increases from 288 to 500 K, the boundary layer transition Reynolds number for the wing section increased by approximately 28% and the surface friction drags decreases by approximately 10.7%. The hot wall enhances the viscous effects of the laminar temperature boundary layer, reduces the Reynolds shear stress and turbulent kinetic energy, and increases the flow stability. However, the velocity gradient and shear stress in the bottom of the turbulent boundary layer decreases, which leads to reduced friction shear stress on the wall surface. Therefore, for the low-aspect-ratio flying wing model, the hot wall can delay the boundary layer transition and reduce the friction drag coefficient in the turbulent region.


Sign in / Sign up

Export Citation Format

Share Document