High-rise building subjected to excessive settlement of its foundation: a case study

2017 ◽  
Vol 8 (2) ◽  
pp. 210-221 ◽  
Author(s):  
Lan Lin ◽  
Adel Hanna ◽  
Anup Sinha ◽  
Lucia Tirca
Keyword(s):  
Pushover Analysis ◽  
Three Dimensional ◽  
Element Model ◽  
Differential Settlement ◽  
Design Stage ◽  
Content Type ◽  
High Rise ◽  
Dimensional Finite Element ◽  
Load Component ◽  
Three Dimensional Finite Element

Purpose Differential settlement between foundations’ elements induces additional stresses in the structural elements. In general, the amount of settlement that a structure can undergo without distress is large, provided that the structure settles uniformly. However, based on the fact that the soil under the foundation may not be uniform in nature and the loads transferred from the superstructure to the foundation are variable, differential settlements between the foundation elements are expected. The purpose of this paper is to evaluate the stresses induced in a typical ten-storey reinforced concrete building subjected to excessive differential settlement. Design/methodology/approach In this investigation, excessive differential settlement up to 75 mm is assigned to the center column on the ground floor that represents the most critical case. A three-dimensional finite element model is developed to perform structural analysis using the software SAP2000, and the nonlinear static pushover analysis is performed. Findings The results of this study show that the building behaves elastically up to 25 mm of differential settlement between its foundation elements, which agrees well with the recommendation given in design manuals. Beyond this value, significant inelastic response is observed in the lower floors and decreases gradually in the higher floors and accordingly, some members have consumed the factor of safety and are in the verge of failure. Originality/value Based on the results of this study, recommendations are made for better communication between the structure and the geotechnical engineers to either limit the differential settlements or incorporate these additional stresses during the design stage of the building. Furthermore, the results of the study can be used to recommend to building codes or design manuals to add a load component due to the anticipated differential settlements of the foundation.

Numerical Analysis of Foundation Settlement for a Fifteen-Story Moving Building

2010 ◽  
Vol 163-167 ◽  
pp. 3694-3700 ◽  
Author(s):  
Qiang Jia ◽  
Xiao Meng ◽  
Xin Zhang
Keyword(s):  
Numerical Analysis ◽  
Pile Foundation ◽  
Three Dimensional ◽  
Element Model ◽  
Differential Settlement ◽  
Structural Safety ◽  
Foundation Settlement ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Slab Foundation

Differential settlement of the new foundation was produced after the building monolithic moving was finished. The internal forces of the top building were changed due to the existence of the differential settlement and the original differential settlement, which affected structural safety. A three-dimensional finite element model was established based on the ANSYS program to attain the foundation settlement law of a fifteen-story moving building. Through calculation and comparation of the settlement values and differential settlement between slab foundation and pile foundation, the pile foundation was finally selected as the construction scheme. Simultaneously, numerical analysis of foundation differential settlement during the moving process was performed. The monitoring results were showen to be in reasonable agreement with the numerical analysis results.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Internal Force on and Deformation of Steel Assembled Supporting Structure of Foundation Pit under Thermal Stress

2021 ◽  
Vol 11 (5) ◽  
pp. 2225
Author(s):  
Fu Wang ◽  
Guijun Shi ◽  
Wenbo Zhai ◽  
Bin Li ◽  
Chao Zhang ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Bending Moment ◽  
High Strength ◽  
Element Model ◽  
Internal Force ◽  
Foundation Pit ◽  
Dimensional Finite Element ◽  
Influence Of Temperature On ◽  
Scale Experiment ◽  
Three Dimensional Finite Element

The steel assembled support structure of a foundation pit can be assembled easily with high strength and recycling value. Steel’s performance is significantly affected by the surrounding temperature due to its temperature sensitivity. Here, a full-scale experiment was conducted to study the influence of temperature on the internal force and deformation of supporting structures, and a three-dimensional finite element model was established for comparative analysis. The test results showed that under the temperature effect, the deformation of the central retaining pile was composed of rigid rotation and flexural deformation, while the adjacent pile of central retaining pile only experienced flexural deformation. The stress on the retaining pile crown changed little, while more stress accumulated at the bottom. Compared with the crown beam and waist beam 2, the stress on waist beam 1 was significantly affected by the temperature and increased by about 0.70 MPa/°C. Meanwhile, the stress of the rigid panel was greatly affected by the temperature, increasing 78% and 82% when the temperature increased by 15 °C on rigid panel 1 and rigid panel 2, respectively. The comparative simulation results indicated that the bending moment and shear strength of pile 1 were markedly affected by the temperature, but pile 2 and pile 3 were basically stable. Lastly, as the temperature varied, waist beam 2 had the largest change in the deflection, followed by waist beam 1; the crown beam experienced the smallest change in the deflection.

Process Modeling in Laser Deposition of Multilayer SS410 Steel

2007 ◽  
Vol 129 (6) ◽  
pp. 1028-1034 ◽  
Author(s):  
Liang Wang ◽  
Sergio Felicelli
Keyword(s):  
Phase Transformation ◽  
Temperature Distribution ◽  
Three Dimensional ◽  
Element Model ◽  
Traverse Speed ◽  
Processing Parameters ◽  
Dimensional Finite Element ◽  
Net Shaping ◽  
Three Dimensional Finite Element ◽  
Continuous Cooling Transformation Diagram

A three-dimensional finite element model was developed to predict the temperature distribution and phase transformation in deposited stainless steel 410 (SS410) during the Laser Engineered Net Shaping (LENS™) rapid fabrication process. The development of the model was carried out using the SYSWELD software package. The model calculates the evolution of temperature in the part during the fabrication of a SS410 plate. The metallurgical transformations are taken into account using the temperature-dependent material properties and the continuous cooling transformation diagram. The ferritic and martensitic transformation as well as austenitization and tempering of martensite are considered. The influence of processing parameters such as laser power and traverse speed on the phase transformation and the consequent hardness are analyzed. The potential presence of porosity due to lack of fusion is also discussed. The results show that the temperature distribution, the microstructure, and hardness in the final part depend significantly on the processing parameters.

Mechanical Simulation of Knee Movement in Basketball Shooting

2013 ◽  
Vol 336-338 ◽  
pp. 760-763
Author(s):  
Hui Yue
Keyword(s):  
Finite Element ◽  
Cruciate Ligament ◽  
Three Dimensional ◽  
Element Model ◽  
Basketball Player ◽  
Knee Movement ◽  
Dimensional Finite Element ◽  
Anterior Cruciate ◽  
Three Dimensional Finite Element

A short explanation of the finite element method as a powerful tool for mathematical modeling is provided, and an application using constitutive modeling of the behavior of ligaments is introduced. Few possible explanations of the role of water in ligament function are extracted from two dimensional finite element models of a classical ligament. The modeling is extended to a three dimensional finite element model for the human anterior cruciate ligament. Simulation of ligament force in pitching motion of basketball player is studied in this paper.

Sign in / Sign up

Export Citation Format

Share Document