Development of a MATLAB/LabVIEW Model for Optimal Tilt Angle and Maximum Power Generation of a PV Module

Author(s):  
Siva Ramakrishna Madeti ◽  
Zameer Ahmad
Author(s):  
Sivaraman P. ◽  
Sharmeela C.

A solar micro inverter is a small-size inverter designed for single solar PV module instead of group of solar PV modules. Each module is equipped with a micro inverter to convert the DC electricity into AC electricity and the micro inverter is placed/installed below the module. The advantages of micro inverters are: reduced effect of shading losses, module degradation and soiling losses, enabled module independence, different rating of micro inverter can be connected in parallel to achieve the desired capacity, additional modules can be included at time which allows the good scalability, string design and sizing are avoided, failure of any micro inverter does not affect the overall power generation, individual MPPT controller for each module increases the power generation, any orientation and tilt angle allows higher design flexibility, lower DC voltage increasing the safety, easy to design, handle and install, requires less maintenance, draws attention of design engineers, contractors, etc.


Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 483
Author(s):  
Novie Ayub Windarko ◽  
Muhammad Nizar Habibi ◽  
Bambang Sumantri ◽  
Eka Prasetyono ◽  
Moh. Zaenal Efendi ◽  
...  

During its operation, a photovoltaic system may encounter many practical issues such as receiving uniform or non-uniform irradiance caused mainly by partial shading. Under uniform irradiance a photovoltaic panel has a single maximum power point. Conversely under non-uniform irradiance, a photovoltaic panel has several local maximum power points and a single global maximum power point. To maximize energy production, a maximum power point tracker algorithm is commonly implemented to achieve the maximum power operating point of the photovoltaic panel. However, the performance of the algorithm will depend on operating conditions such as variation in irradiance. Presently, most of existing maximum power point tracker algorithms work only in a single condition: either uniform or non-uniform irradiance. This paper proposes a new maximum power point tracker algorithm for photovoltaic power generation that is designed to work under uniform and partial shading irradiance conditions. Additionally, the proposed maximum power point tracker algorithm aims to provide: (1) a simple math algorithm to reduce computational load, (2) fast tracking by evaluating progress for every single executed duty cycle, (3) without random steps to prevent jumping duty cycle, and (4) smooth variable steps to increase accuracy. The performances of the proposed algorithm are evaluated by three conditions of uniform and partial shading irradiance where a targeted maximum power point is located: (1) far from, (2) near, and (3) laid between initial positions of particles. The simulation shows that the proposed algorithm successfully tracks the maximum power point by resulting in similar power values in those three conditions. The proposed algorithm could handle the partial shading condition by avoiding the local maxima power point and finding the global maxima power point. Comparisons of the proposed algorithm and other well-known algorithms such as differential evolution, firefly, particle swarm optimization, and grey wolf optimization are provided to show the superiority of the proposed algorithm. The results show the proposed algorithm has better performance by providing faster tracking, faster settling time, higher accuracy, minimum oscillation and jumping duty cycle, and higher energy harvesting.


2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Abhijit V. Padgavhankar ◽  
Sharad W. Mohod

The electric power supplied by photovoltaic module depends on light intensity and temperature. It is necessary to control the operating point to draw the maximum power of photovoltaic module. This paper presents the design and implementation of digital power converters using Proteus software. Its aim is to enhance student’s learning for virtual system modeling and to simulate in software for PIC microcontroller along with the hardware design. The buck and boost converters are designed to interface with the renewable energy source that is PV module. PIC microcontroller is used as a digital controller, which senses the PV electric signal for maximum power using sensors and output voltage of the dc-dc converter and according to that switching pulse is generated for the switching of MOSFET. The implementation of proposed system is based on learning platform of Proteus virtual system modeling (VSM) and the experimental results are presented.


2016 ◽  
Vol 6 (5) ◽  
pp. 1269-1277 ◽  
Author(s):  
Alberto Dolara ◽  
George Cristian Lazaroiu ◽  
Sonia Leva ◽  
Giampaolo Manzolini ◽  
Luca Votta

Sign in / Sign up

Export Citation Format

Share Document