The computation of the effects of harmonic currents on transformers using a coupled electromagnetic-thermal FEM approach

Author(s):  
J. Driesen ◽  
R. Belmans ◽  
K. Hameyer
Keyword(s):  
Machines ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 139
Author(s):  
Matthias Vollat ◽  
Dominik Krahe ◽  
Frank Gauterin

To reduce torque oscillations in electric motors, harmonic current injection (HCI) has been used in industry for some time. For this purpose, higher harmonic currents calculated in advance are injected into the machine. Since the general conditions for the machine can change during its life cycle, this article presents a method that makes it possible to change the parameters of HCI during operation. For this purpose, sensor signals are used to detect the reaction of the electric motor to small variations of the HCI parameters. The knowledge gained in this way is used to make further suitable variations. FEM simulations were used to verify the effectiveness of the approach. The results show that the algorithm can independently optimize the HCI parameters during runtime and reduces the amplitude of the 6th harmonic in the torque by 87% for a permanent magnet synchronous machine.


Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2183 ◽  
Author(s):  
Dionisis Voglitsis ◽  
Fotis Valsamas ◽  
Nick Rigogiannis ◽  
Nick Papanikolaou

Active anti-islanding schemes that are based on the injection of harmonic currents, such as the measurement of the impedance at a specific frequency or similar techniques, have been proposed for anti-islanding protection in photovoltaic (PV) systems due to their low impact on inverter active power, their fast detection response in island, and reduced non-detection zone (NDZ). Integer multiples of the fundamental frequency as well as sub/inter-harmonics have both been used for the implementation of those schemes. Although utilization of sub/inter-harmonics present significant advantages, they also present significant limitations. This work investigates those limitations, particularly the ones that are caused by the parallel operation of multiple inverters. In addition, the distortion effect that is caused in the output current of the widely used PV microinverters with pseudo dc-link (PV Pdc-MICs) is discussed and thoroughly analyzed. It is concluded that when the injection is performed asynchronously (without communication among the inverters) sub/inter-harmonics are unsuitable for utilization under the parallel operation of multiple inverters. It is worth noting that a strategy is proposed in the current work that retains the effectiveness of the harmonic injection scheme under the injection of integer multiples of fundamental frequency. On the other hand, the distortion effect that is caused by the sub/inter-harmonics on PV Pdc-MICs output current, has been evaluated as insignificant when harmonics are used for anti-islanding purposes. Finally, the theoretical/mathematical outcomes of this work are supported by simulation and experimental results.


Author(s):  
Shashi lalvani ◽  
Lei Kerr ◽  
Shamal Lalvani ◽  
Dominic Olaguera-Delogu

Abstract A careful evaluation of the earlier model (1-2) for electrochemical frequency modulation (EFM) involving two sinusoidal applied potentials for the determination of corrosion parameters shows an algebraic error. Although the missing term in the original derivation appears to be insignificant, it is found that errors involved in corrosion current determination, and especially in evaluation of the Tafel slopes can be very significant, which is of consequence because of the rising popularity of this technique. The magnitude of error is found to be a function of the inherent corrosion characteristics (anodic and cathodic Tafel slopes) of the corroding material as well as the applied peak potential of the modulation. A corrected model with detailed steps showing the appropriate math is presented. In addition, using the experimental data available in the literature, the errors involved in estimating the corrosion parameters by the earlier EFM model of Bosch et al (1-2) are evaluated. The corrected corrosion current and the Tafel slopes can be recovered from the incorrect model without the benefit of the harmonic currents, as shown in this paper.The analysis is also presented for the case of only one applied sinusoidal frequency modulation, which offers several advantages over the multiple frequency modulation.


Author(s):  
Mikhail A. Sherkunkov ◽  
Stepan G. Tiguntsev

This article explores the method of joint suppression of harmonic currents, balancing currents and partial compensation of the reactive power of a non-linear asymmetric load connected in a triangle using a device installed on the low voltage side of a power transformer


Sign in / Sign up

Export Citation Format

Share Document