OFDM indoor positioning based on TDOAs: Performance analysis and experimental results

Author(s):  
C. Gentner ◽  
S. Sand ◽  
A. Dammann
Author(s):  
Hai

In this paper, a new Raspberry PI supercomputer cluster architecture is proposed. Generally, to gain speed at petaflops and exaflops, typical modern supercomputers based on 2009-2018 computing technologies must consume between 6 MW and 20 MW of electrical power, almost all of which is converted into heat, requiring high cost for cooling technology and Cooling Towers. The management of heat density has remained a key issue for most centralized supercomputers. In our proposed architecture, supercomputers with highly energy-efficient mobile ARM processors are a new choice as it enables them to address performance, power, and cost issues. With ARM’s recent introduction of its energy-efficient 64-bit CPUs targeting servers, Raspberry Pi cluster module-based supercomputing is now within reach. But how is the performance of supercomputers-based mobile multicore processors? Obtained experimental results reported on the proposed approach indicate the lower electrical power and higher performance in comparison with the previous approaches.


2021 ◽  
Author(s):  
Paolo Carbone ◽  
Guido De Angelis ◽  
Valter Pasku ◽  
Alessio De Angelis ◽  
Marco Dionigi ◽  
...  

<div><div><div><p>This paper describes the design and realization of a Magnetic Indoor Positioning System. The system is entirely realized using off-the-shelf components and is based on inductive coupling between resonating coils. Both system-level architecture and realization details are described along with experimental results. The realized system exhibits a maximum positioning error of less than 10 cm in an indoor environment over a 3×3 m2 area. Extensive experiments in larger areas, in non-line-of-sight conditions, and in unfavorable geometric configurations, show sub-meter accuracy, thus validating the robustness of the system with respect to other existing solutions.</p></div></div></div>


Author(s):  
Anca Fluerasu ◽  
A. Vervisch-Picois ◽  
G. Boiero ◽  
G. Ghinamo ◽  
P. Lovisolo ◽  
...  

2020 ◽  
Vol 9 (2) ◽  
pp. 74
Author(s):  
Eric Hsueh-Chan Lu ◽  
Jing-Mei Ciou

With the rapid development of surveying and spatial information technologies, more and more attention has been given to positioning. In outdoor environments, people can easily obtain positioning services through global navigation satellite systems (GNSS). In indoor environments, the GNSS signal is often lost, while other positioning problems, such as dead reckoning and wireless signals, will face accumulated errors and signal interference. Therefore, this research uses images to realize a positioning service. The main concept of this work is to establish a model for an indoor field image and its coordinate information and to judge its position by image eigenvalue matching. Based on the architecture of PoseNet, the image is input into a 23-layer convolutional neural network according to various sizes to train end-to-end location identification tasks, and the three-dimensional position vector of the camera is regressed. The experimental data are taken from the underground parking lot and the Palace Museum. The preliminary experimental results show that this new method designed by us can effectively improve the accuracy of indoor positioning by about 20% to 30%. In addition, this paper also discusses other architectures, field sizes, camera parameters, and error corrections for this neural network system. The preliminary experimental results show that the angle error correction method designed by us can effectively improve positioning by about 20%.


Author(s):  
Alok Kumar Mohanty ◽  
K B Yadav

<em>Multi-phase machines are considered serious contenders as compared to the three phase machines for variable applications in generating mode. </em><em>This paper presents the transient performance analysis of a multi-phase induction machine operating in six-phase mode for power generation. In this paper the simulation and experimental analysis of a six-phase machine in generating mode have been made. The simulations are made and the machine functionality was investigated during no-load and when subjected to different types of loads. Experimental results are provided to confirm the ability of these models to represent during no load as well as during load period and the result were found to be satisfactory for power generation</em>.


Sign in / Sign up

Export Citation Format

Share Document