A study on reliable position estimation in kinematic positioning for single frequency GNSS receiver

Author(s):  
Hiromi In ◽  
Hiroyuki Hatano ◽  
Masahiro Fujii ◽  
Atsushi Ito ◽  
Yu Watanabe
Author(s):  
M. Rehak ◽  
J. Skaloud

Mapping with Micro Aerial Vehicles (MAVs whose weight does not exceed 5&amp;thinsp;kg) is gaining importance in applications such as corridor mapping, road and pipeline inspections, or mapping of large areas with homogeneous surface structure, e.g. forest or agricultural fields. In these challenging scenarios, integrated sensor orientation (ISO) improves effectiveness and accuracy. Furthermore, in block geometry configurations, this mode of operation allows mapping without ground control points (GCPs). Accurate camera positions are traditionally determined by carrier-phase GNSS (Global Navigation Satellite System) positioning. However, such mode of positioning has strong requirements on receiver’s and antenna’s performance. In this article, we present a mapping project in which we employ a single-frequency, low-cost (<&amp;thinsp;$100) GNSS receiver on a MAV. The performance of the low-cost receiver is assessed by comparing its trajectory with a reference trajectory obtained by a survey-grade, multi-frequency GNSS receiver. In addition, the camera positions derived from these two trajectories are used as observations in bundle adjustment (BA) projects and mapping accuracy is evaluated at check points (ChP). Several BA scenarios are considered with absolute and relative aerial position control. Additionally, the presented experiments show the possibility of BA to determine a camera-antenna spatial offset, so-called lever-arm.


2019 ◽  
Vol 57 (2) ◽  
pp. 881-892 ◽  
Author(s):  
Chuanbao Zhao ◽  
Yunbin Yuan ◽  
Baocheng Zhang ◽  
Min Li

2019 ◽  
Vol 10 (1) ◽  
pp. 15-20 ◽  
Author(s):  
A. P. Aleshkin ◽  
T. O. Myslivtsev ◽  
S. V. Nikiforov ◽  
P. V. Savochkin ◽  
I. V. Sakhno ◽  
...  

2020 ◽  
Vol 12 (2) ◽  
pp. 285
Author(s):  
Chenlong Deng ◽  
Qian Liu ◽  
Xuan Zou ◽  
Weiming Tang ◽  
Jianhui Cui ◽  
...  

The loose combination (LC) and the tight combination (TC) are two different models in the combined processing of four global navigation satellite systems (GNSSs). The former is easy to implement but may be unusable with few satellites, while the latter should cope with the inter-system bias (ISB) and is applicable for few tracked satellites. Furthermore, in both models, the inter-frequency bias (IFB) in the GLObal NAvigation Satellite System (GLONASS) system should also be removed. In this study, we aimed to investigate the performance difference of ambiguity resolution and position estimation between these two models simultaneously using the single-frequency data of all four systems (GPS + GLONASS + Galileo + BeiDou Navigation Satellite System (BDS)) in three different environments, i.e., in an open area, with surrounding high buildings, and under a block of high buildings. For this purpose, we first provide the definition of ISB and IFB from the perspective of the hardware delays, and then propose practical algorithms to estimate the IFB rate and ISB. Thereafter, a comprehensive performance comparison was made between the TC and LC models. Experiments were conducted to simulate the above three observation environments: the typical situation and situations suffering from signal obstruction with high elevation angles and limited azimuths, respectively. The results show that in a typical situation, the TC and LC models achieve a similar performance. However, when the satellite signals are severely obstructed and few satellites are tracked, the float solution and ambiguity fixing rates in the LC model are dramatically decreased, while in the TC model, there are only minor declines and the difference in the ambiguity fixing rates can be as large as 30%. The correctly fixed ambiguity rates in the TC model also had an improvement of around 10%. Once the ambiguity was fixed, both models achieved a similar positioning accuracy.


2017 ◽  
Vol 24 (1) ◽  
pp. 127-142 ◽  
Author(s):  
Piotr Kaniewski ◽  
Rafał Gil ◽  
Stanisław Konatowski

Abstract The paper presents methods of on-line and off-line estimation of UAV position on the basis of measurements from its integrated navigation system. The navigation system installed on board UAV contains an INS and a GNSS receiver. The UAV position, as well as its velocity and orientation are estimated with the use of smoothing algorithms. For off-line estimation, a fixed-interval smoothing algorithm has been applied. On-line estimation has been accomplished with the use of a fixed-lag smoothing algorithm. The paper includes chosen results of simulations demonstrating improvements of accuracy of UAV position estimation with the use of smoothing algorithms in comparison with the use of a Kalman filter.


2021 ◽  
pp. 1-19
Author(s):  
Ankit Jain ◽  
Steffen Schön

Abstract In urban areas, the Global Navigation Satellite System (GNSS) can lead to position errors of tens of meters due to signal obstruction and severe multipath effects. In cases of 3D-positioning, the vertical coordinate is estimated less accurately than are the horizontal coordinates. Multisensor systems can enhance navigation performance in terms of accuracy, availability, continuity and integrity. However, the addition of multiple sensors increases the system cost, and thereby the applicability to low-cost applications is limited. By using the concept of receiver clock modelling (RCM), the position estimation can be made more robust; the use of high-sensitivity (HS) GNSS receivers can improve the system availability and continuity. This paper investigates the integration of a low-cost HS GNSS receiver with an external clock in urban conditions; subsequently, the gain in the navigation performance is evaluated. GNSS kinematic data is recorded in an urban environment with multiple geodetic-grade and HS receivers. The external clock stability information is incorporated through the process noise matrix in a Kalman filter when estimating the position, velocity and time states. Results shows that the improvement in the precision of the height component and vertical velocity with both receivers is about 70% with RCM compared with the estimates obtained without applying RCM. Pertaining accuracy, the improvement in height with RCM is found to be about 70% and 50% with geodetic and HS receivers, respectively. In terms of availability, the HS receiver delivers an 100% output compared with a geodetic receiver, which provides an output 99⋅4% of the total experiment duration.


2015 ◽  
Vol 901 (7) ◽  
pp. 2-7
Author(s):  
A.P. Karpik ◽  
◽  
I.G. Ganagina ◽  
N.S. Kosarev ◽  
D.N. Goldobin ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document