Thermal Reflow Effect in Multi-mode Waveguide of S-Bend Resonator with Mode Discrimination

Novel S-Bend Resonator Based on a Multi-Mode Waveguide with Mode Discrimination for a Refractive Index Sensor

Sensors ◽

10.3390/s19163600 ◽

2019 ◽

Vol 19 (16) ◽

pp. 3600 ◽

Cited By ~ 1

Author(s):

Do-Hyun Kim ◽

Su-Jin Jeon ◽

Jae-Sang Lee ◽

Seok-Ho Hong ◽

Young-Wan Choi

Keyword(s):

Refractive Index ◽

Single Mode ◽

Higher Order ◽

Optical Resonators ◽

Refractive Index Sensor ◽

Bending Loss ◽

Wide Line ◽

Mode Discrimination ◽

The Difference ◽

Multi Mode

In this paper, a multi-mode waveguide-based optical resonator is proposed for an integrated optical refractive index sensor. Conventional optical resonators have been studied for single-mode waveguide-based resonators to enhance the performance, but mass production is limited owing to the high fabrication costs of nano-scale structures. To overcome this problem, we designed an S-bend resonator based on a micro-scale multi-mode waveguide. In general, multi-mode waveguides cannot be utilized as optical resonators, because of a performance degradation resulting from modal dispersion and an output transmission with multi-peaks. Therefore, we exploited the mode discrimination phenomenon using the bending loss, and the resulting S-bend resonator yielded an output transmission without multi-peaks. This phenomenon is utilized to remove higher-order modes efficiently using the difference in the effective refractive index between the higher-order and fundamental modes. As a result, the resonator achieved a Q-factor and sensitivity of 2.3 × 103 and 52 nm/RIU, respectively, using the variational finite-difference time-domain method. These results show that the multi-mode waveguide-based S-bend resonator with a wide line width can be utilized as a refractive index sensor.

Get full-text (via PubEx)

Joint Inversion of Rayleigh and Love Dispersion Curves Extracted from Ambient Seismic Noise Based on Secular Function

Journal of Physics Conference Series ◽

10.1088/1742-6596/2148/1/012047 ◽

2022 ◽

Vol 2148 (1) ◽

pp. 012047

Author(s):

Feng Gong ◽

Xiaofei Chen ◽

Youhua Fan ◽

Xuefeng Liu ◽

Haibing Tang

Keyword(s):

Objective Function ◽

Dispersion Curve ◽

Seismic Noise ◽

Joint Inversion ◽

Dispersion Curves ◽

Ambient Seismic Noise ◽

Inversion Method ◽

Mode Dispersion ◽

Mode Discrimination ◽

Multi Mode

Abstract Traditional multi-mode dispersion curve inversion requires correct mode discrimination. However, when the stratum contains complex structures such as low-speed soft interlayer or high-speed hard interlayer, the dispersion curve may show phenomena such as “mode kissing” and “mode jumping”, which can easily cause mode misjudgment and lead to erroneous inversion results. Based on the “secular function”, this paper constructs a new type of objective function applied to the inversion of dispersion curve. This objective function does not require prior mode discrimination, which effectively solves the “mode misjudgment” problem of multi-mode dispersion curve inversion. The joint inversion of Rayleigh and Love dispersion curves extracted from ambient seismic noise is used to improve the constraint of the inversion and avoid the inversion falling into a local minimum in the case of a large-scale search of parameters. Finally, a numerical simulation was performed to verify the feasibility of the new inversion method.

Get full-text (via PubEx)

Mode Identification Using Photometry and Spectroscopy

International Astronomical Union Colloquium ◽

10.1017/s0252921100011155 ◽

2004 ◽

Vol 193 ◽

pp. 466-469

Author(s):

Joris De Ridder ◽

Conny Aerts ◽

Marc-Antoine Dupret

Keyword(s):

Moment Method ◽

Amplitude Ratios ◽

Stepwise Approach ◽

Mode Identification ◽

New Variant ◽

Additional Mode ◽

Mode Discrimination ◽

Multi Mode

AbstractWe tested a stepwise approach to combine photometry and spectroscopy for mode identification where we first used the photometric amplitude ratios to restrict the degree l, then did a spectroscopic mode identification, and finally fitted the photometric amplitudes to restrict the list of candidate modes. For the spectroscopic mode identification, we implemented an efficient multi-mode moment method variant. We conclude that this new variant works well, but that the photometric amplitudes are too model sensitive to do any additional mode discrimination.

Get full-text (via PubEx)

Multi-mode light microscopy of microtubule assembly dynamics and chromosome movement in vivo and In vitro

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100166117 ◽

1996 ◽

Vol 54 ◽

pp. 730-731

Author(s):

E. D. Salmon ◽

J. C. Waters ◽

C. Waterman-Storer

Keyword(s):

Imaging System ◽

Ccd Camera ◽

Transmitted Light ◽

Microtubule Assembly ◽

Live Cells ◽

Optical Efficiency ◽

Multiple Band ◽

Multi Mode

We have developed a multi-mode digital imaging system which acquires images with a cooled CCD camera (Figure 1). A multiple band pass dichromatic mirror and robotically controlled filter wheels provide wavelength selection for epi-fluorescence. Shutters select illumination either by epi-fluorescence or by transmitted light for phase contrast or DIC. Many of our experiments involve investigations of spindle assembly dynamics and chromosome movements in live cells or unfixed reconstituted preparations in vitro in which photodamage and phototoxicity are major concerns. As a consequence, a major factor in the design was optical efficiency: achieving the highest image quality with the least number of illumination photons. This principle applies to both epi-fluorescence and transmitted light imaging modes. In living cells and extracts, microtubules are visualized using X-rhodamine labeled tubulin. Photoactivation of C2CF-fluorescein labeled tubulin is used to locally mark microtubules in studies of microtubule dynamics and translocation. Chromosomes are labeled with DAPI or Hoechst DNA intercalating dyes.

Get full-text (via PubEx)