scholarly journals UET-Headpose: A sensor-based top-view head pose dataset

Author(s):  
Linh Nguyen Viet ◽  
Tuan Nguyen Dinh ◽  
Duc Tran Minh ◽  
Hoang Nguyen Viet ◽  
Quoc Long Tran
Keyword(s):  
Author(s):  
J. Frank ◽  
P.-Y. Sizaret ◽  
A. Verschoor ◽  
J. Lamy

The accuracy with which the attachment site of immunolabels bound to macromolecules may be localized in electron microscopic images can be considerably improved by using single particle averaging. The example studied in this work showed that the accuracy may be better than the resolution limit imposed by negative staining (∽2nm).The structure used for this demonstration was a halfmolecule of Limulus polyphemus (LP) hemocyanin, consisting of 24 subunits grouped into four hexamers. The top view of this structure was previously studied by image averaging and correspondence analysis. It was found to vary according to the flip or flop position of the molecule, and to the stain imbalance between diagonally opposed hexamers (“rocking effect”). These findings have recently been incorporated into a model of the full 8 × 6 molecule.LP hemocyanin contains eight different polypeptides, and antibodies specific for one, LP II, were used. Uranyl acetate was used as stain. A total of 58 molecule images (29 unlabelled, 29 labelled with antl-LPII Fab) showing the top view were digitized in the microdensitometer with a sampling distance of 50μ corresponding to 6.25nm.


Author(s):  
Nicolas Boisset ◽  
Jean-Christophe Taveau ◽  
Jean Lamy ◽  
Terence Wagenknecht ◽  
Michael Radermacher ◽  
...  

Hemocyanin, the respiratory pigment of the scorpion Androctonus australis is composed of 24 kidney shaped subunits. A model of architecture supported by many indirect arguments has been deduced from electron microscopy (EM) and immuno-EM. To ascertain, the disposition of the subunits within the oligomer, the 24mer was submitted to three-dimensional reconstruction by the method of single-exposure random-conical tilt series.A sample of native hemocyanin, prepared with the double layer negative staining technique, was observed by transmisson electron microscopy under low-dose conditions. Six 3D-reconstructions were carried out indenpendently from top, side and 45°views. The results are composed of solid-body surface representations, and slices extracted from the reconstruction volume.The main two characters of the molecule previously reported by Van Heel and Frank, were constantly found in the solid-body surface representations. These features are the presence of two different faces called flip and flop and a rocking of the molecule around an axis passing through diagonnally opposed hexamers. Furthermore, in the solid-body surface of the top view reconstruction, the positions and orientations of the bridges connecting the half molecules were found in excellent agreement with those predicted by the model.


Author(s):  
Jong Hak Lee ◽  
Yu Jun Lee ◽  
Jung Sam Kim ◽  
Seo Kyung Jeong ◽  
Min Su Kim ◽  
...  

Abstract In this work, crystalline defects (dislocations) occurred in the silicon substrate during annealing SOD (Spin On Dielectric) which is an easy choice for its superior STI gap-fill ability. The reversal of address data that share same SIO (Signal Input Out) line in a DQ arises from crystalline defects. The failure analysis of physical methods has difficulty finding minute defects within the active because it is scarcely detectable from the top view. Situation can be well understood by electrical analysis using the nano probe. Due to its ability to probing contact nodes around the fail area, a ring type crystalline defect which is hardly detected from the top view was effectively analyzed by 3D TEM with the assistance of nano probe. This work shows that hybrid analysis of electrical method by nano probe and physical method by 3D TEM is useful and effective in failure analysis in semiconductor.


Author(s):  
Vassilis G. Kaburlasos ◽  
Chris Lytridis ◽  
Christos Bazinas ◽  
George A. Papakostas ◽  
Abdelwahab Naji ◽  
...  
Keyword(s):  

Work ◽  
2021 ◽  
Vol 68 (s1) ◽  
pp. S151-S159
Author(s):  
Zhihui Liu ◽  
T. Rotte ◽  
S. Anjani ◽  
P. Vink

BACKGROUND: Staggered seats are a solution for the Flying-V aircraft, where the cabin’s longitudinal axis has a 26 degrees angle with respect to the direction of flight, to compensate for an otherwise oblique sitting position. However, little is known on acceptable pitches in this staggered configuration. OBJECTIVE: The goal of this research is to evaluate the comfort of different pitches for seats that are staggered relative to the cabin’s longitudinal axis. METHODS: Two rows of staggered seats are positioned at three different pitches (27, 29 and 31 inches). 53 participants were seated in each setup. For each, a questionnaire was completed including questions on comfort and discomfort, top view photos were taken to analyse postures and physical dimensions were recorded to define passengers’ space. RESULTS: Comfort as well as discomfort were significantly different for the three setups. The comfort at 27 inches was seen as unacceptably low. The 29 and 31-inch configurations showed to result in acceptable levels of comfort, comparable to higher-end seating layouts. There were very little complaints about space in lateral direction (elbow and seat width), showing the advantage of having your won armrest and shoulder space in the staggered configuration. Interesting was that at larger pitches more complaints were found for the seat characteristics, probably in the shorter pitch the other discomfort was overruling this. CONCLUSION: The 26-degree staggered configuration offers improvements in shoulder- and elbow-space. The results for the 29- and 31-inch are expected to allow enough design freedom for further exploration of such a configuration for the Flying-V cabin interior.


Author(s):  
Ahmet Firintepe ◽  
Mohamed Selim ◽  
Alain Pagani ◽  
Didier Stricker

Sign in / Sign up

Export Citation Format

Share Document