Multifunction Filter using CNTFET based Current Conveyors

2021 ◽  
Author(s):  
Manish Dash ◽  
Dipankar Pal
Keyword(s):  
Current Conveyors ◽  
Multifunction Filter

NOVEL VOLTAGE-MODE MULTIFUNCTION FILTER USING ONLY TWO DDCCs

2008 ◽  
Vol 17 (06) ◽  
pp. 1161-1172 ◽  
Author(s):  
HUA-PIN CHEN ◽  
KUO-HSIUNG WU
Keyword(s):  
Cmos Technology ◽  
The Other ◽  
Current Conveyors ◽  
Lowpass Filter ◽  
Analog Filter ◽  
Chip Area ◽  
Voltage Mode ◽  
Single Output ◽  
Multifunction Filter ◽  
Component Matching

A new voltage-mode biquad with four inputs and four outputs using only two differential difference current conveyors (DDCCs), two grounded capacitors, and two resistors is proposed. The proposed circuit can act as a multifunction voltage-mode filter with one or three inputs and four outputs and can perform simultaneous realization of voltage-mode notch, highpass, bandpass, and lowpass filter signals from the four output terminals, respectively, without any component choice conditions. On the other hand, it also can act as a universal voltage-mode filter with four inputs and a single output and can realize five generic voltage-mode filter signals from the same configuration without any component-matching conditions. Finally, to verify our architecture, we have designed this analog filter chip with TSMC 0.35 μm 2P4M CMOS technology. This chip operates to 1.125 MHz and consumes 30.95 mW. The chip area of the analog filter is about 0.822 mm2.

scholarly journals Programmable Voltage-Mode Multifunction Filter Using Two Current Conveyors and One Operational Transconductance Amplifier

1996 ◽  
Vol 19 (3) ◽  
pp. 133-138 ◽  
Author(s):  
Muhammad Taher Abuelma'atti ◽  
Azhar Quddus
Keyword(s):  
Low Temperature ◽  
Active Filter ◽  
Current Conveyors ◽  
Operational Transconductance Amplifier ◽  
Voltage Mode ◽  
Transconductance Amplifier ◽  
Biquadratic Filter ◽  
Multifunction Filter ◽  
Single Input

A new voltage-mode active-filter with single input and three outputs is presented. The parameters of the proposed filter are programmable and the filter uses grounded capacitors. The proposed circuit can simultaneously realize lowpass, highpass, and bandpass biquadratic filter functions and enjoys low temperature sensitivities.

scholarly journals High-Input Impedance Voltage-Mode Multifunction Filter with Four Grounded Components and Only Two Plus-Type DDCCs

2010 ◽  
Vol 2010 ◽  
pp. 1-5 ◽  
Author(s):  
Hua-Pin Chen
Keyword(s):  
Input Impedance ◽  
Current Conveyors ◽  
High Input ◽  
High Input Impedance ◽  
Voltage Mode ◽  
Biquadratic Filter ◽  
Multifunction Filter ◽  
Component Matching ◽  
Single Input ◽  
Passive Sensitivity

This paper introduces a novel voltage-mode multifunction biquadratic filter with single input and four outputs using two plus-type differential difference current conveyors (DDCCs) and four grounded passive components. The filter can realize inverting highpass, inverting bandpass, noninverting lowpass, and noninverting bandpass filter responses, simultaneously. It still maintains the following advantages: (i) using grounded capacitors attractive for integration and absorbing shunt parasitic capacitance, (ii) using grounded resistors at allXterminals of DDCCs suitable for the variations of filter parameters and absorbing series parasitic resistances at allXterminals of DDCCs, (iii) high-input impedance good for cascadability, (iv) no need to change the filter topology, (v) no need to component-matching conditions, (vi) low active and passive sensitivity performances, and (vii) simpler configuration due to the use of plus-type DDCCs only. HSPICE and MATLAB simulations results are provided to demonstrate the theoretical analysis.

Sign in / Sign up

Export Citation Format

Share Document