Buck Converter and SEPIC Based Electronic Power Supply Design with MPPT and Voltage Regulation for Small Satellite Applications

2017 ◽  
Author(s):  
Rachid Darbali-Zamora ◽  
Nicolas Cobo-Yepes ◽  
John E. Salazar-Duque ◽  
Eduardo I. Ortiz-Rivera ◽  
Amilcar A. Rincon-Charris
Keyword(s):  
Power Supply ◽  
Voltage Regulation ◽  
Buck Converter ◽  
Small Satellite ◽  
Satellite Applications

scholarly journals Analysis and Design for Output Voltage Regulation in Constant-on-Time-Controlled Fly-Buck Converter

Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 1886
Author(s):  
Younghoon Cho ◽  
Paul Jang
Keyword(s):  
Output Voltage ◽  
Voltage Regulation ◽  
Design Guidelines ◽  
Buck Converter ◽  
Design Guideline ◽  
Analysis And Design ◽  
Flyback Converter ◽  
Auxiliary Power ◽  
Primary Output ◽  
Output Capacitor

Fly-buck converter is a multi-output converter with the structure of a synchronous buck converter structure on the primary side and a flyback converter structure on the secondary side, and can be utilized in various applications due to its many advantages. In terms of control, the primary side of the fly-buck converter has the same structure as a synchronous buck converter, allowing the constant-on-time (COT) control to be applied to the fly-buck converter. However, due to the inherent energy transfer principle, the primary-side output voltage regulation of COT controlled fly-buck converters may be poor, which can deteriorate the overall converter performance. Therefore, the primary output capacitor must be carefully designed to improve the voltage regulation characteristics. In this paper, a theoretical analysis of the output voltage regulation in COT controlled fly-buck converter is conducted, and based on this, a design guideline for the primary output capacitor considering the output voltage regulation is presented. The validity of the analysis and design guidelines was verified using a 5 W prototype of the COT controlled fly-buck converter for telecommunication auxiliary power supply.

scholarly journals Compensated Single Input Multiple Output Flyback Converter

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3009
Author(s):  
Mohammad Tahan ◽  
David O. Bamgboje ◽  
Tingshu Hu
Keyword(s):  
Transient Response ◽  
Current Mode ◽  
Voltage Regulation ◽  
Buck Converter ◽  
Output Channel ◽  
Flyback Converter ◽  
Input Multiple Output ◽  
Voltage Deviation ◽  
Single Input ◽  
The Cross

A new single-input multiple-output (SIMO) converter is proposed in this work by incorporating flyback and buck converters in a master–slave configuration. The objective of this work is to address the cross regulation problem, achieve tight voltage regulation, improve the circuit form factor and attain a fast transient response for a SIMO flyback converter. The flyback converter maintains the output channels within 10% of their rated voltages and the SIMO buck converter is placed in series with the flyback converter such that it compensates for the output voltage deviation. Moreover, a time multiplexing switching scheme decouples output channel to eliminate the cross-regulation problem and remove the need for an additional winding transformer per each output channel. A type II compensator with a peak current mode controller was designed to achieve faster transient response which is critical for the proposed configuration. A thorough steady-state analysis was carried out on a triple output channel topology to obtain the design criteria and component values. MATLAB/Simscape modelling and simulation was used to validate the effectiveness of the proposed converter with the result yielding satisfactory transience even with load disturbance. Additionally, the result of the proposed converter is compared with previously published works.

Design and Implementation of Mid-Frequency Magnetron Sputtering Power Supply Based on TL494 and MCU

2013 ◽  
Vol 709 ◽  
pp. 408-412
Author(s):  
Yan Ling Zhao ◽  
Rong Xing Liu
Keyword(s):  
Magnetron Sputtering ◽  
Power Supply ◽  
Current Mode ◽  
Voltage Regulation ◽  
Control Circuit ◽  
Constant Current ◽  
Loop Control ◽  
Pulse Width Modulator ◽  
Digital Pulse ◽  
The Stability

Abstract. A mid-frequency magnetron sputtering (MFMS) power supply based on TL494 and MCU was introduced. A Buck Chopper and full bridge inverter were applied to the main circuit. The PWM controller TL494 was used in the Buck voltage-regulation control circuit to realize closed loop control. The drive signal of the IGBT in full bridge inverter was based on precise digital pulse width modulator (DPWM) signal produced by the MCU M30290. The DPWM can be set by potentiometer so the power supply can output the square wave with adjustable frequency and duty cycle. The power supply was operated in constant current mode. For micro or strong arcing of the target, different safeguards were adopted by the control circuit. At last, the system test and experimental results show that the stability, reliability and tuning range of the MFMS power supply can meet the requirements of the magnetron sputtering coating.

Voltage regulation of buck converter with constant power load: An adaptive power shaping control

2021 ◽  
Vol 115 ◽  
pp. 104891
Author(s):  
Wei He ◽  
Mohammad Masoud Namazi ◽  
Hamid Reza Koofigar ◽  
Mohammad Ali Amirian ◽  
Josep M. Guerrero
Keyword(s):  
Voltage Regulation ◽  
Buck Converter ◽  
Constant Power ◽  
Power Load ◽  
Adaptive Power ◽  
Constant Power Load

Development of Appropriate Power Distribution Design for Can-Sized satellite (canSAT)

2021 ◽  
Vol 02 (02) ◽  
Author(s):  
Devina Cristine Marubin ◽  
◽  
Sim Sy Yi ◽  
Keyword(s):  
Power System ◽  
Data Acquisition ◽  
Power Supply ◽  
Communication System ◽  
Power Distribution ◽  
Low Cost ◽  
Small Satellite ◽  
Power Budget ◽  
Space Agency ◽  
Rules Set

Can-Sized satellite (canSAT) is a small satellite that is used for educational purpose. CanSAT offer student to build their satellites with their creativity which make the learning process more effective. In Malaysia, SiswaSAT is held by the Malaysia Space Agency for students in different categories to participate and build their satellites according to rules set and it should be a low-cost project. CanSAT can be divided into few parts which are communication system, onboard data acquisition, ground control station and power system. The power system is one of the important and heaviest subsystems, it needed to supply power, but weight and size are one of the main concerned as the canSAT should not exceed the required weight and selecting power supply that is matched with the overall power budget that has small size and lightweight is challenging. Therefore, the power supply selection should consider this detail. The power distribution design should be able to supply an appropriate amount of current and voltage to the components according to their specification. This study aims to develop and test the proposed prototype which is named ScoreSAT able to provide data and have enough power supply for the whole operation. Therefore, an initiative to develop the appropriate power distribution design for canSAT is taken to overcome the problem of the power system. Moreover, each subsystem needs to be tested by obtaining the results from the onboard data acquisition and transmit the data using the communication system before integrating into the power system. ScoreSAT prototype needs to carry the system that is mounted inside, thus the space inside the prototype needs to be fully utilized for the whole system to fit in. ScoreSAT completes the mission by obtaining data acquisition during the operation.

Sign in / Sign up

Export Citation Format

Share Document