Kinematics and dynamics modelling of all terrain articulated tracked vehicles

Author(s):  
Hao Lin ◽  
Wei Lin ◽  
En Li ◽  
Zize Liang
10.12737/8471 ◽  
2015 ◽  
Vol 4 (4) ◽  
pp. 179-190 ◽  
Author(s):  
Клубничкин ◽  
Evgeniy Klubnichkin ◽  
Клубничкин ◽  
Vladislav Klubnichkin ◽  
Бухтояров ◽  
...  

The research of multilink mechanism on the example of propulsor track harvester ЛЗ-5 was made. Propulsor of track harvester (CH) is a multilink mechanism, as it consists of track tracks, including a large number of tracks hingedly connected to each other. For research, we selected the program UM Tracked Vehicles, as it is most appropriate for the task. At the stage of development of the design documentation, such virtual testing in economic terms is more favorable than the natural prototype testing.


1994 ◽  
Vol 23 (sup1) ◽  
pp. 34-46
Author(s):  
P. Bourassa ◽  
G. Payre ◽  
B. Marcos ◽  
B. Ezzerrouqi ◽  
S. Reiher

2015 ◽  
Vol 794 ◽  
pp. 419-426
Author(s):  
Philipp Tempel ◽  
Philipp Miermeister ◽  
Armin Lechler ◽  
Andreas Pott

This paper covers the kinematics and dynamics modelling of the mechatronic model for a 6 DOF cable-driven parallel robot and derives a real-time capable simulation model for such robots. The governing equations of motion for the platform are derived using Newton-Euler formalism, furthermore, the pulley kinematics of the winches and a linear spring-damper based cable model is introduced. Once the equations of motion are derived, closed-form force distribution is implemented and simulation results of the real-time capable model for the cable-driven parallel robot IPAnema3 are presented. Given the real-time capability, the presented model can be used for hardware-in-the-loop simulation or controller design, but also for case studies of highly dynamic or large-scale robots.


2013 ◽  
Vol 46 (8) ◽  
pp. 69-73 ◽  
Author(s):  
Xh. Bajrami ◽  
A. Dermaku ◽  
A. Shala ◽  
R. Likaj

Author(s):  
P. Bourassa ◽  
G. Payre ◽  
B. Marcos ◽  
B. Ezzerrouqi ◽  
S. Reiher

2015 ◽  
Vol 1 (1) ◽  
pp. 5-16
Author(s):  
John Ohoiwutun

Utilization of conventional energy sources such as coal, fuel oil, natural gas and others on the one hand has a low operating cost, but on the other side of the barriers is the greater source of diminishing returns and, more importantly, the emergence of environmental pollution problems dangerous to human life. This study aims to formulate the kinematics and dynamics to determine the movement of Solar Power Mower. In this study, using solar power as an energy source to charge the battery which then runs the robot. Design and research was conducted in the Department of Mechanical Workshop Faculty of Engineering, University of Hasanuddin of Gowa. Control system used is a manual system using radio wave transmitter and receiver which in turn drive the robot in the direction intended. Experimental results showed that treatment with three variations of the speed of 6.63 m / s, 8.84 m / s and 15.89 m / sec then obtained the best results occur in grass cutting 15.89 sec and high-speed cutting grass 5 cm. Formulation of kinematics and dynamics for lawn mowers, there are 2 control input variables, x and y ̇ ̇ 3 to control the output variables x, y and θ so that there is one variable redudant. Keywords: mobile robots, lawn mower, solar power


2014 ◽  
Vol 8 (6) ◽  
pp. 1037
Author(s):  
Ratna Chow ◽  
Ahmad Faizal Salleh ◽  
Mohd Shahril Salim ◽  
Wan Mohd Radzi Bin Rusli ◽  
Norazian Abd. Razak ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document