Microstructure and Mechanical Properties of Lu2O3-Doped Porous Silicon Nitride Ceramics Using Phenolic Resin as Pore-Forming Agent

2009 ◽  
Vol 7 (3) ◽  
pp. 391-398 ◽  
Author(s):  
Xiaowei Yin ◽  
Xiangming Li ◽  
Litong Zhang ◽  
Laifei Cheng ◽  
Yongsheng Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silicon Nitride ◽  
Porous Silicon ◽  
Phenolic Resin ◽  
Microstructure And Mechanical Properties ◽  
Nitride Ceramics

Effects of Sintering Additives on the Microstructure and Mechanical Properties of Silicon Nitride Ceramics by GPS

2010 ◽  
Vol 105-106 ◽  
pp. 27-30 ◽  
Author(s):  
Wei Ru Zhang ◽  
Feng Sun ◽  
Ting Yan Tian ◽  
Xiang Hong Teng ◽  
Min Chao Ru ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Transformation ◽  
Silicon Nitride ◽  
Porous Silicon ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Additives ◽  
Microstructure And Mechanical Properties ◽  
Nitride Ceramics

Silicon nitride ceramics were prepared by gas pressure sintering (GPS) with different sintering additives, including La2O3, Sm2O3 and Al2O3. Effect of sintering additives on the phase-transformation, microstructure and mechanical properties of porous silicon nitride ceramics was investigated. The results show that the reaction of sintering additives each other and with SiO2 had key effects on the phase-transformation, grain growing and grain boundaries. With 9MPa N2 atmosphere pressure, holding 1h at 1850°C, adding 10wt% one of the La2O3, Sm2O3, Al2O3, porous silicon nitride was prepared and the relative density was 78%, 72%, 85% respectively. The flexural strength was less than 500MPa, and the fracture toughness was less than 4.8MPam1/2. Dropping compounds sintering additives, such as La2O3+Al2O3, Sm2O3+Al2O3 effectively improves the sintering and mechanical properties. The relative density was 99.2% and 98.7% with 10wt% compounds sintering additives. The grain ratio of length to diameter was up to 1:8. The flexural strength was more than 900MPa, and the fracture toughness was more than 8.9MPam1/2.

Fabrication of High-Porosity Silicon Nitride Ceramics with Excellent Mechanical Properties

2011 ◽  
Vol 284-286 ◽  
pp. 1339-1342
Author(s):  
Shao Yun Shan ◽  
Qing Ming Jia ◽  
Ya Ming Wang ◽  
Jin Hui Peng
Keyword(s):  
Mechanical Properties ◽  
Silicon Nitride ◽  
Porous Silicon ◽  
Aspect Ratio ◽  
High Aspect Ratio ◽  
High Strength ◽  
High Porosity ◽  
Microstructure And Mechanical Properties ◽  
Nitride Ceramics ◽  
Sintering Conditions

High-porosity silicon nitride ceramics with excellent mechanical properties were fabricated by the carbothermal reduction of SiO2. The influences of sintering conditions on microstructure and mechanical properties were studied. The results showed that microstructure and mechanical properties of porous silicon nitride ceramics were dependent mostly on the sintering conditions. The sintered porous silicon nitride ceramics exhibited the formation of fibrous microstructure with submicrometer-sized, high-aspect ratio b-Si3N4 grains, and uniform pore structure. Porous Si3N4 ceramics with a porosity of about 70%, and a flexural strength of about 70 MPa were obtained by sintering at 1750°C, with lower rate of temperature rise and no retaining time. The high strength was attributed to fine, high-aspect ratio b-Si3N4 grains and uniform pores between grains.

scholarly journals Influence of MXene (Ti3C2) Phase Addition on the Microstructure and Mechanical Properties of Silicon Nitride Ceramics

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5221
Author(s):  
Jaroslaw Wozniak ◽  
Mateusz Petrus ◽  
Tomasz Cygan ◽  
Artur Lachowski ◽  
Bogusława Adamczyk-Cieślak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Transformation ◽  
Silicon Nitride ◽  
Powder Processing ◽  
Sintering Process ◽  
Microstructure And Mechanical Properties ◽  
Plasma Sintering ◽  
Nitride Ceramics ◽  
Spark Plasma

This paper discusses the influence of Ti3C2 (MXene) addition on silicon nitride and its impact on the microstructure and mechanical properties of the latter. Composites were prepared through powder processing and sintered using the spark plasma sintering (SPS) technic. Relative density, hardness and fracture toughness, were analyzed. The highest fracture toughness at 5.3 MPa·m1/2 and the highest hardness at HV5 2217 were achieved for 0.7 and 2 wt.% Ti3C2, respectively. Moreover, the formation of the Si2N2O phase was observed as a result of both the MXene addition and the preservation of the α-Si3N4→β-Si3N4 phase transformation during the sintering process.

Sign in / Sign up

Export Citation Format

Share Document