scholarly journals Effect of Side Wind on a Simplified Car Model: Experimental and Numerical Analysis

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Emmanuel Guilmineau ◽  
Francis Chometon
Keyword(s):  
Reynolds Number ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Numerical Data ◽  
Numerical Results ◽  
Separated Flows ◽  
Wind Gust ◽  
Bluff Bodies ◽  
Test Model ◽  
Steady Flows

A prior analysis of the effect of steady cross wind on full size cars or models must be conducted when dealing with transient cross wind gust effects on automobiles. The experimental and numerical tests presented in this paper are performed on the Willy square-back test model. This model is realistic compared with a van-type vehicle; its plane underbody surface is parallel to the ground, and separations are limited to the base for moderated yaw angles. Experiments were carried out in the semi-open test section at the Conservatoire National des Arts et Métiers, and computations were performed at the Ecole Centrale de Nantes (ECN). The ISIS-CFD flow solver, developed by the CFD Department of the Fluid Mechanics Laboratory of ECN, used the incompressible unsteady Reynolds-averaged Navier–Stokes equations. In this paper, the results of experiments obtained at a Reynolds number of 0.9×106 are compared with numerical data at the same Reynolds number for steady flows. In both the experiments and numerical results, the yaw angle varies from 0 deg to 30 deg. The comparison between experimental and numerical results obtained for aerodynamic forces, wall pressures, and total pressure maps shows that the unsteady ISIS-CFD solver correctly reflects the physics of steady three-dimensional separated flows around bluff bodies. This encouraging result allows us to move to a second step dealing with the analysis of unsteady separated flows around the Willy model.

Fluid Flow and Lateral Fluid Dispersion in Bounded Granular Beds

2002 ◽  
Author(s):  
Azita Soleymani ◽  
Eveliina Takasuo ◽  
Piroz Zamankhan ◽  
William Polashenski
Keyword(s):  
Reynolds Number ◽  
Porous Media ◽  
Numerical Solutions ◽  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Numerical Results ◽  
Transition To Turbulence ◽  
Wide Range

Results are presented from a numerical study examining the flow of a viscous, incompressible fluid through random packing of nonoverlapping spheres at moderate Reynolds numbers (based on pore permeability and interstitial fluid velocity), spanning a wide range of flow conditions for porous media. By using a laminar model including inertial terms and assuming rough walls, numerical solutions of the Navier-Stokes equations in three-dimensional porous packed beds resulted in dimensionless pressure drops in excellent agreement with those reported in a previous study (Fand et al., 1987). This observation suggests that no transition to turbulence could occur in the range of Reynolds number studied. For flows in the Forchheimer regime, numerical results are presented of the lateral dispersivity of solute continuously injected into a three-dimensional bounded granular bed at moderate Peclet numbers. Lateral fluid dispersion coefficients are calculated by comparing the concentration profiles obtained from numerical and analytical methods. Comparing the present numerical results with data available in the literature, no evidence has been found to support the speculations by others for a transition from laminar to turbulent regimes in porous media at a critical Reynolds number.

Effects of stator splitter blades on aerodynamic performance of a single-stage transonic axial compressor

2020 ◽  
Vol 14 (4) ◽  
pp. 7369-7378
Author(s):  
Ky-Quang Pham ◽  
Xuan-Truong Le ◽  
Cong-Truong Dinh
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Operating Stability ◽  
Length Coverage

Splitter blades located between stator blades in a single-stage axial compressor were proposed and investigated in this work to find their effects on aerodynamic performance and operating stability. Aerodynamic performance of the compressor was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations using the k-e turbulence model with a scalable wall function. The numerical results for the typical performance parameters without stator splitter blades were validated in comparison with experimental data. The numerical results of a parametric study using four geometric parameters (chord length, coverage angle, height and position) of the stator splitter blades showed that the operational stability of the single-stage axial compressor enhances remarkably using the stator splitter blades. The splitters were effective in suppressing flow separation in the stator domain of the compressor at near-stall condition which affects considerably the aerodynamic performance of the compressor.

Numerical and Experimental Analysis of 3D Micro-Corrugated Wing in Gliding Flight

2021 ◽  
Author(s):  
Nasim Chitsaz ◽  
Kamran Siddiqui ◽  
Romeo Marian ◽  
Javaan S. Chahl
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Three Dimensional Model ◽  
Wing Model ◽  
Computational Fluid Dynamics Analysis ◽  
Gliding Flight ◽  
Flat Profile

Abstract In this study, computational fluid dynamics analysis was performed on a three-dimensional model of a Libellulidae wing to determine aerodynamic performance in gliding flight. The wing is comprised of various corrugated features alongside the spanwise and chordwise directions, as well as twist. The detailed features of real 3D dragonfly wing models, including all the corrugations through both span and chord, have not been considered in the past for a detailed aerodynamic analysis. The simulations were conducted by solving the Navier-Stokes equations to demonstrate gliding performance over a range of angles of attack at low Reynolds numbers. The numerical model was validated against experimental data obtained from a fabricated corrugated wing model using particle image velocimetry. The numerical results demonstrate that bio-inspired wings with corrugations compared to flat profile wings generate more lift with lower drag, trapping the vortices in the valleys of wing corrugation leading to delayed flow separation and delayed stall. The experimental and numerical results demonstrate that the methodology presented in this study can be used to measure bio-inspired 3D wing flow characteristics, including the influence of complex corrugations on aerodynamic performance. These findings contribute to the advancement of knowledge required for designing an optimized bioinspired micro air vehicle.

Numerical simulation of boundary-layer transition and transition control

1989 ◽  
Vol 199 ◽  
pp. 403-440 ◽  
Author(s):  
E. Laurien ◽  
L. Kleiser
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Transition Process ◽  
Numerical Results ◽  
Boundary Layer Transition ◽  
Two Dimensional ◽  
Layer Transition ◽  
Longitudinal Vortices ◽  
Tollmien Schlichting

The laminar-turbulent transition process in a parallel boundary-layer with Blasius profile is simulated by numerical integration of the three-dimensional incompressible Navier-Stokes equations using a spectral method. The model of spatially periodic disturbances developing in time is used. Both the classical Klebanoff-type and the subharmonic type of transition are simulated. Maps of the three-dimensional velocity and vorticity fields and visualizations by integrated fluid markers are obtained. The numerical results are compared with experimental measurements and flow visualizations by other authors. Good qualitative and quantitative agreement is found at corresponding stages of development up to the one-spike stage. After the appearance of two-dimensional Tollmien-Schlichting waves of sufficiently large amplitude an increasing three-dimensionality is observed. In particular, a peak-valley structure of the velocity fluctuations, mean longitudinal vortices and sharp spike-like instantaneous velocity signals are formed. The flow field is dominated by a three-dimensional horseshoe vortex system connected with free high-shear layers. Visualizations by time-lines show the formation of A-structures. Our numerical results connect various observations obtained with different experimental techniques. The initial three-dimensional steps of the transition process are consistent with the linear theory of secondary instability. In the later stages nonlinear interactions of the disturbance modes and the production of higher harmonics are essential.We also study the control of transition by local two-dimensional suction and blowing at the wall. It is shown that transition can be delayed or accelerated by superposing disturbances which are out of phase or in phase with oncoming Tollmien-Schlichting instability waves, respectively. Control is only effective if applied at an early, two-dimensional stage of transition. Mean longitudinal vortices remain even after successful control of the fluctuations.

scholarly journals Nonlinear amplification in hydrodynamic turbulence

2021 ◽  
Vol 930 ◽  
Author(s):  
Kartik P. Iyer ◽  
Katepalli R. Sreenivasan ◽  
P.K. Yeung
Keyword(s):  
Reynolds Number ◽  
Isotropic Turbulence ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Developed Turbulence ◽  
Advection Term ◽  
Nonlinear Amplification

Using direct numerical simulations performed on periodic cubes of various sizes, the largest being $8192^3$ , we examine the nonlinear advection term in the Navier–Stokes equations generating fully developed turbulence. We find significant dissipation even in flow regions where nonlinearity is locally absent. With increasing Reynolds number, the Navier–Stokes dynamics amplifies the nonlinearity in a global sense. This nonlinear amplification with increasing Reynolds number renders the vortex stretching mechanism more intermittent, with the global suppression of nonlinearity, reported previously, restricted to low Reynolds numbers. In regions where vortex stretching is absent, the angle and the ratio between the convective vorticity and solenoidal advection in three-dimensional isotropic turbulence are statistically similar to those in the two-dimensional case, despite the fundamental differences between them.

A Calculation Scheme for Three-Dimensional Viscous Incompressible Flows

1987 ◽  
Vol 109 (4) ◽  
pp. 345-352 ◽  
Author(s):  
M. Reggio ◽  
R. Camarero
Keyword(s):  
Incompressible Flows ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Numerical Data ◽  
Momentum Balance ◽  
Navier Stokes ◽  
Test Cases ◽  
Pressure Gradients ◽  
Navier Stokes Equations

A numerical procedure to solve three-dimensional incompressible flows in arbitrary shapes is presented. The conservative form of the primitive-variable formulation of the time-dependent Navier-Stokes equations written for a general curvilinear coordiante system is adopted. The numerical scheme is based on an overlapping grid combined with opposed differencing for mass and pressure gradients. The pressure and the velocity components are stored at the same location: the center of the computational cell which is used for both mass and the momentum balance. The resulting scheme is stable and no oscillations in the velocity or pressure fields are detected. The method is applied to test cases of ducting and the results are compared with experimental and numerical data.

Numerical Three-Dimensional Pressure Patterns in a Recess of a Turbulent and Compressible Hybrid Journal Bearing

2003 ◽  
Vol 125 (2) ◽  
pp. 301-308 ◽  
Author(s):  
Mathieu Helene ◽  
Mihai Arghir ◽  
Jean Frene
Keyword(s):  
Reynolds Number ◽  
Mach Number ◽  
Journal Bearing ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Wire Mesh ◽  
Primary Concern ◽  
Reference Parameters ◽  
Exit Mach Number

The present work investigates the flow in the feeding recess of a hybrid journal bearing. Numerical integration of the complete Navier-Stokes equations was performed with an appropriate turbulence model. Of primary concern is the pressure field on the rotating journal surface that is commonly known as the recess pressure pattern. The goal of the work is to determine the influences of fluid compressibility, operating conditions and recess geometry. Reference parameters selected for this study comprise feeding Reynolds number Rea of 2.105, sliding Reynolds number Rec of 5.103 and recess depth over film thickness ratio e/H of 2.2. Compressibility was considered first. Three values of the axial exit Mach number were selected for computation, namely 0.2, 0.45, and 0.7. As no significant variation was found, the Mach number was fixed at 0.45 in subsequent studies concerning other parameters:     Feeding Reynolds number, Rea       2.104,2.105,4.105     Recess depth, e/H           0, 2.2, 8     Feedhole axis inclination        90°, 135°, 165°     Feedhole location (Figs. 1(a) and 13)   centered, downstream offset. As each parameter is varied, wire mesh plot of pressure and its sectional profiles are examined and effects of varying various parameters are discussed in reference to flow processes as they may affect the support characteristics of the hybrid journal bearing.

scholarly journals Linear pulse structure and signalling in a film flow on an inclined plane

1999 ◽  
Vol 396 ◽  
pp. 37-71 ◽  
Author(s):  
LEONID BREVDO ◽  
PATRICE LAURE ◽  
FREDERIC DIAS ◽  
THOMAS J. BRIDGES
Keyword(s):  
Free Surface ◽  
Saddle Point ◽  
Convective Instability ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Numerical Results ◽  
Navier Stokes ◽  
Surface Boundary ◽  
Navier Stokes Equations ◽  
Surface Boundary Conditions

The film flow down an inclined plane has several features that make it an interesting prototype for studying transition in a shear flow: the basic parallel state is an exact explicit solution of the Navier–Stokes equations; the experimentally observed transition of this flow shows many properties in common with boundary-layer transition; and it has a free surface, leading to more than one class of modes. In this paper, unstable wavepackets – associated with the full Navier–Stokes equations with viscous free-surface boundary conditions – are analysed by using the formalism of absolute and convective instabilities based on the exact Briggs collision criterion for multiple k-roots of D(k, ω) = 0; where k is a wavenumber, ω is a frequency and D(k, ω) is the dispersion relation function.The main results of this paper are threefold. First, we work with the full Navier–Stokes equations with viscous free-surface boundary conditions, rather than a model partial differential equation, and, guided by experiments, explore a large region of the parameter space to see if absolute instability – as predicted by some model equations – is possible. Secondly, our numerical results find only convective instability, in complete agreement with experiments. Thirdly, we find a curious saddle-point bifurcation which affects dramatically the interpretation of the convective instability. This is the first finding of this type of bifurcation in a fluids problem and it may have implications for the analysis of wavepackets in other flows, in particular for three-dimensional instabilities. The numerical results of the wavepacket analysis compare well with the available experimental data, confirming the importance of convective instability for this problem.The numerical results on the position of a dominant saddle point obtained by using the exact collision criterion are also compared to the results based on a steepest-descent method coupled with a continuation procedure for tracking convective instability that until now was considered as reliable. While for two-dimensional instabilities a numerical implementation of the collision criterion is readily available, the only existing numerical procedure for studying three-dimensional wavepackets is based on the tracking technique. For the present flow, the comparison shows a failure of the tracking treatment to recover a subinterval of the interval of unstable ray velocities V whose length constitutes 29% of the length of the entire unstable interval of V. The failure occurs due to a bifurcation of the saddle point, where V is a bifurcation parameter. We argue that this bifurcation of unstable ray velocities should be observable in experiments because of the abrupt increase by a factor of about 5.3 of the wavelength across the wavepacket associated with the appearance of the bifurcating branch. Further implications for experiments including the effect on spatial amplification rate are also discussed.

Finite-Reynolds-Number Effects in Steady, Three-Dimensional Airway Reopening

2006 ◽  
Vol 128 (4) ◽  
pp. 573-578 ◽  
Author(s):  
Andrew L. Hazel ◽  
Matthias Heil
Keyword(s):  
Reynolds Number ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Elastic Tube ◽  
Navier Stokes ◽  
Fluid Inertia ◽  
Navier Stokes Equations ◽  
Airway Reopening ◽  
Reynolds Number Effects ◽  
Steady Propagation

Motivated by the physiological problem of pulmonary airway reopening, we study the steady propagation of an air finger into a buckled elastic tube, initially filled with viscous fluid. The system is modeled using geometrically non-linear, Kirchhoff-Love shell theory, coupled to the free-surface Navier-Stokes equations. The resulting three-dimensional, fluid-structure-interaction problem is solved numerically by a fully coupled finite element method. Our study focuses on the effects of fluid inertia, which has been neglected in most previous studies. The importance of inertial forces is characterized by the ratio of the Reynolds and capillary numbers, Re∕Ca, a material parameter. Fluid inertia has a significant effect on the system’s behavior, even at relatively small values of Re∕Ca. In particular, compared to the case of zero Reynolds number, fluid inertia causes a significant increase in the pressure required to drive the air finger at a given speed.

Sign in / Sign up

Export Citation Format

Share Document