Investigation of Pre-Stall Behavior in an Axial Compressor Rotor—Part I: Unsteadiness of Tip Clearance Flow

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Yanhui Wu ◽  
Qingpeng Li ◽  
Jiangtao Tian ◽  
Wuli Chu
Keyword(s):  
Unsteady Flow ◽  
Periodic Variation ◽  
Flow Fields ◽  
Low Energy ◽  
Tip Clearance ◽  
Flow Mechanism ◽  
Equilibrium Solutions ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow

To investigate the pre-stall behavior of an axial flow compressor rotor, which was experimentally observed with spike-type stall inception, systematic experimental and whole-passage simulations were laid out to analyze the internal flow fields in the test rotor. In this part, emphases were put on the analyses of experimental results and the predicted results from steady simulations and unsteady simulations, which converged to equilibrium solutions with nearly periodic fluctuations of efficiency. The objective was to uncover the unsteady behavior of tip clearance flow and its associated flow mechanism at near-stall conditions. To validate the steady simulation results, the predicted total characteristics and spanwise distributions of aerodynamic parameters were first compared with the measured steady data, and a good agreement was achieved. Then, the numerically obtained unsteady flow fields during one period of efficiency fluctuations were analyzed in detail. The instantaneous flow structure near casing showed that tip secondary vortex (TSV), which appeared in the previous unsteady single-passage simulations, did exist in tip flow fields of whole-passage simulations. The cyclical motion of this vortex was the main source of the nearly periodic variation of efficiency. The simulated active period of TSV increased when the mass flow rate decreased. The simulated frequency of TSV at flow condition very close to the measured stall point equaled the frequency of the characteristic hump identified from the instantaneous casing pressure measurements. This coincidence implied that the occurrence of this hump was most probably a result of the movement of TSV. Further flow field analyses indicated that the interaction of the low-energy leakage fluid from adjacent passages with the broken-down tip leakage vortex (TLV) was the flow mechanism for the formation of TSV. Once TSV appeared in tip flow fields, its rearward movement would lead to a periodic variation in near-tip blade loading, which in turn altered the strength of TLV and TSV, accordingly, the low-energy regions associated with the breakdown of TLV and the motion of TSV, thus establishing a self-sustained unsteady flow oscillation in tip flow fields.

Characteristics of Tip Clearance Flow Instability in a Transonic Compressor

2010 ◽  
Author(s):  
Chunill Hah ◽  
Melanie Voges ◽  
Martin Mueller ◽  
Heinz-Peter Schiffer
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Flow Instability ◽  
Tip Clearance ◽  
Piv Measurements ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Tip Clearance Vortex

In the present study, unsteady flow phenomena due to tip clearance flow instability in a modern transonic axial compressor rotor are studied in detail. First, unsteady flow characteristics due the oscillating tip clearance vortex measured with the particle image velocimetry (PIV) and casing-mounted unsteady pressure transducers are analyzed and compared to numerical results with a large eddy simulation (LES). Then, measured characteristic frequencies of the unsteady flow near stall operation are investigated. The overall purpose of the study is to advance the current understanding of the unsteady flow field near the blade tip in an axial transonic compressor rotor near the stall operating condition. Flow interaction between the tip leakage vortex and the passage shock is inherently unsteady in a transonic compressor. The currently applied PIV measurements indicate that the flow near the tip region is unsteady even at the design condition. This self-induced unsteadiness increases significantly as the compressor operates toward the stall condition. PIV data show that the tip clearance vortex oscillates substantially near stall. The calculated unsteady characteristics from LES agree well with the PIV measurements. Calculated unsteady flow fields show that the formation of the tip clearance vortex is intermittent and the concept of vortex breakdown from steady flow analysis does not seem to apply in the current flow field. Fluid with low momentum near the pressure side of the blade close to the leading edge periodically spills over into the adjacent blade passage. The spectral analysis of measured end wall and blade surface pressure shows that there are two dominant frequencies near stall. One frequency is about 40–60% of the rotor rotation and the other dominant frequency is about 40–60% of the blade passing frequency (BPF). The first frequency represents the movement of a large blockage over several consecutive blade passages against the rotor rotation. The second frequency represents traditional tip flow instability, which has been widely observed in subsonic compressors. The LES simulations show that the second frequency is due to movement of the instability vortex.

Role of Tip-Leakage Vortices and Passage Shock in Stall Inception in a Swept Transonic Compressor Rotor

2004 ◽  
Author(s):  
Chunill Hah ◽  
Douglas C. Rabe ◽  
Aspi R. Wadia
Keyword(s):  
Boundary Layer ◽  
Flow Fields ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Tip Clearance Vortex

The current paper reports on investigations aimed at advancing the understanding of the flow field near the casing of a forward-swept transonic compressor rotor. The role of tip clearance flow and its interaction with the passage shock on stall inception are analyzed in detail. Steady and unsteady three-dimensional viscous flow calculations are applied to obtain flow fields at various operating conditions. The numerical results are first compared with available measured data. Then, the numerically obtained flow fields are interrogated to identify the roles of flow interactions between the tip clearance flow, the passage shock, and the blade/endwall boundary layers. In addition to the flow field with nominal tip clearance, two more flow fields are analyzed in order to identify the mechanisms of blockage generation: one with zero tip clearance, and one with nominal tip clearance on the forward portion of the blade and zero clearance on the aft portion. The current study shows that the tip clearance vortex does not break down, even when the rotor operates in a stalled condition. Interaction between the shock and the suction surface boundary layer causes the shock, and therefore the tip clearance vortex, to oscillate. However, for the currently investigated transonic compressor rotor, so-called breakdown of the tip clearance vortex does not occur during stall inception. The tip clearance vortex originates near the leading edge tip, but moves downward in the spanwise direction inside the blade passage. A low momentum region develops above the tip clearance vortex from flow originating from the casing boundary layer. The low momentum area builds up immediately downstream of the passage shock and above the core vortex. This area migrates toward the pressure side of the blade passage as the flow rate is decreased. The low momentum area prevents incoming flow from passing through the pressure side of the passage and initiates stall inception. It is well known that inviscid effects dominate tip clearance flow. However, complex viscous flow structures develop inside the casing boundary layer at operating conditions near stall.

Effect of tip clearance size on the performance of a low-reaction transonic axial compressor rotor

2019 ◽  
Vol 234 (2) ◽  
pp. 127-142
Author(s):  
Wei Zhu ◽  
Songtao Wang ◽  
Longxin Zhang ◽  
Jun Ding ◽  
Zhongqi Wang
Keyword(s):  
Numerical Simulations ◽  
Dynamic Balance ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Phenomena

This study aimed to enhance the understanding of flow phenomena in low-reaction aspirated compressors. Three-dimensional, multi-passage steady and unsteady numerical simulations are performed to investigate the performance sensitivity to tip clearance variation on the first-stage rotor of a multistage low-reaction aspirated compressor. Three kinds of tip clearance sizes including 1.0τ, 2.0τ and 3.0τ are modeled, in which 1.0τ corresponds to the designed tip clearance size of 0.2 mm. The steady numerical simulations show that the overall performance of the rotor moves toward lower mass flow rate when the tip clearance size is increased. Moreover, energy losses, efficiency reduction and stall margin decrease are also observed with increasing tip clearance size. This can be mostly attributed to the damaging impact of intense tip clearance flow. For unsteady simulation, the result shows periodical oscillation of the tip leakage vortex and a “two-passage periodic structure” in the tip region at the near-stall point. The occurrence of the periodical oscillation is due to the severe interaction between the tip clearance flow and the shock wave. However, the rotor operating state is still stable at this working point because a dynamic balance is established between the tip clearance flow and incoming flow.

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size on the Tip Clearance Flow Structure at Near Stall Operation

2014 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz
Keyword(s):  
Unsteady Flow ◽  
Flow Structure ◽  
Flow Instability ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Clearance Flow ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

Numerical Investigations of the Coupled Flow Through a Subsonic Compressor Rotor and Axial Skewed Slot

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yangfeng Zhang
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through ◽  
Flow Compressor

In order to advance the understanding of the fundamental mechanisms of axial skewed slot casing treatment and their effects on the subsonic axial-flow compressor flow field, the coupled unsteady flow through a subsonic compressor rotor and the axial skewed slot was simulated with a state-of-the-art multiblock flow solver. The computational results were first compared with available measured data, that showed the numerical procedure calculates the overall effect of the axial skewed slot correctly. Then, the numerically obtained flow fields were interrogated to identify the physical mechanism responsible for improvement in stall margin of a modern subsonic axial-flow compressor rotor due to the discrete skewed slots. It was found that the axial skewed slot casing treatment can increase the stall margin of subsonic compressor by repositioning of the tip clearance flow trajectory further toward the trailing of the blade passage and retarding the movement of the incoming∕tip clearance flow interface toward the rotor leading edge plane.

Investigation of Pre-Stall Behavior in an Axial Compressor Rotor—Part II: Flow Mechanism of Spike Emergence

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Yanhui Wu ◽  
Qingpeng Li ◽  
Jiangtao Tian ◽  
Wuli Chu
Keyword(s):  
Axial Flow ◽  
Internal Flow ◽  
Propagation Speed ◽  
Suction Side ◽  
Flow Fields ◽  
Development Stage ◽  
Tip Clearance ◽  
The Self ◽  
Flow Mechanism ◽  
Compressor Rotor

To investigate the pre-stall behavior of an axial flow compressor rotor, which was experimentally observed with spike-type stall inception, systematic experimental and whole-passage simulations were laid out to analyze the internal flow fields in the test rotor. In this part, emphases were put on the analyses of the flow fields of whole-passage simulation, which finally diverged, and the objective was to uncover the flow mechanism of short length scale disturbance (or spike) emergence. The numerical result demonstrated that the test rotor was of spike-type stall initiation. The numerical probes, arranged ahead of the rotor to monitor the static pressure variation, showed that there first appear two pips on the curves. After one rotor revolution, there was only one pip left, spreading at about 33.3% rotor speed. This propagation speed was almost the same as that of the spike observed in experiments. The further analysis of the flow field revealed a concentrated blockage sector on the flow annuls ahead of rotor developed gradually with the self-adjustment of flow fields. The two pins on monitoring curves corresponded to two local blockage regions in near-tip passages, and were designated as B1 and B2, respectively. The correlation between the tip secondary vortices (TSVs) in the preceding and native passages was the flow mechanism for propagation of B2 and B1, thereby leading to their spread speed approximate to the active period of the TSV in one passage. Furthermore, the self-sustained unsteady cycle of TSVs was the underlying flow mechanism for the occurrence of the so-called “tip clearance spillage flow” and “tip clearance backflow.” Because B2 was the tip-front of the blockage sector, TSVs associated with its propagation became stronger and stronger, so that the “tip clearance backflow” induced by it was capable of spilling into the next passage below the blade tip. This phenomenon was regarded as the threshold event where B2 started to evolve into a spike. The distinctive flow feature during the development stage of the spike was the occurrence of a separation focus on the suction side in the affected passages, which changed the self-sustained unsteady cycle of the TSV substantially. A three-dimensional vortex originating from this focus led to a drastic increase in the strength of the TSV, which, in turn, led to a rapid increase in the “tip clearance backflow” induced by the TSV and the radial extent of spillage flow.

Numerical Investigation of Relation Between Unsteady Behavior of Tip Leakage Vortex and Rotating Disturbance in a Transonic Axial Compressor Rotor

2008 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
H. Sasaki
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Rotating Instability

The purpose of this study is to have a better understanding of the unsteady behavior of tip clearance flow at near-stall condition from a multi-passage simulation and to clarify the relation between such unsteadiness and rotating disturbance. This study is motivated by the following concern. A single passage simulation has revealed the occurrence of the tip leakage vortex breakdown at near-stall condition in a transonic axial compressor rotor, leading to the unsteadiness of the tip clearance flow field in the rotor passage. These unsteady flow phenomena were similar to those in the rotating instability, which is classified in one of the rotating disturbances. In other words it is possible that the tip leakage vortex breakdown produces a rotating disturbance such as the rotating instability. Three-dimensional unsteady RANS calculation was conducted to simulate the rotating disturbance in a transonic axial compressor rotor (NASA Rotor 37). The four-passage simulation was performed so as to capture a short length scale disturbance like the rotating instability and the spike-type stall inception. The simulation demonstrated that the unsteadiness of tip leakage vortex, which was derived from the vortex breakdown at near-stall condition, invoked the rotating disturbance in the rotor, which is similar to the rotating instability.

Investigation of the Tip Clearance Flow Inside and at the Exit of a Compressor Rotor Passage—Part I: Mean Velocity Field

1983 ◽  
Vol 105 (1) ◽  
pp. 1-12 ◽  
Author(s):  
A. Pandya ◽  
B. Lakshminarayana
Keyword(s):  
Boundary Layer ◽  
Tip Clearance ◽  
Mean Flow ◽  
Ensemble Averaging ◽  
Mean Velocity ◽  
Tip Clearance Flow ◽  
Wall Boundary Layer ◽  
Compressor Rotor ◽  
Wall Boundary ◽  
Clearance Flow

This paper reports on an experimental study of the nature of the tip clearance flow in a moderately loaded compressor rotor. The measurements reported were obtained using a stationary two-sensor, hot-wire probe in combination with an ensemble averaging technique. The flow field was surveyed at various radial locations and at ten axial locations, four of which were inside the blade passage in the clearance region and the remaining six outside the passage. Variations of the mean flow properties in the tangential and the radial directions at various axial locations were derived from the data. Variation of leakage velocity at different axial stations and the annulus-wall boundary layer profiles from passage-averaged mean velocities were also estimated. The results indicate that there exists a region of strong interaction of the leakage flow with the annulus-wall boundary layer at half-chord. The profiles are well-behaved beyond this point. The rotor exit flow is found to be uniform beyond 3/4 blade chord downstream of the rotor trailing edge.

Unsteady tip clearance flow pattern in an isolated axial compressor rotor with micro tip injection

2007 ◽  
Vol 16 (4) ◽  
pp. 309-320 ◽  
Author(s):  
Shaojuan Geng ◽  
Hongwu Zhang ◽  
Jingyi Chen ◽  
Weiguang Huang
Keyword(s):  
Flow Pattern ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Tip Injection
Sign in / Sign up

Export Citation Format

Share Document