Influence of Coolant Density on Turbine Blade Platform Film-Cooling

2012 ◽  
Vol 4 (2) ◽  
Author(s):  
Diganta P. Narzary ◽  
Kuo-Chun Liu ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Flow Rate ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Mainstream Flow ◽  
Purge Flow

Detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform of a five-blade linear cascade. The parameters chosen were freestream turbulence intensity, upstream stator-rotor purge flow rate, discrete-hole film-cooling blowing ratio, and coolant-to-mainstream density ratio. The measurement technique adopted was temperature sensitive paint (TSP) technique. Two turbulence intensities of 4.2% and 10.5%; three purge flows between the range of 0.25% and 0.75% of mainstream flow rate; three blowing ratios between 1.0 and 1.8; and three density ratios between 1.1 and 2.2 were investigated. Purge flow was supplied via a typical double-toothed stator-rotor seal, whereas the discrete-hole film-cooling was accomplished via two rows of cylindrical holes arranged along the length of the platform. The inlet and the exit Mach numbers were 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 7.5 * 105 based on the exit velocity and chord length of the blade. Results indicated that platform film-cooling effectiveness decreased with turbulence intensity, increased with purge flow rate and density ratio, and possessed an optimum blowing ratio value.

Influence of Coolant Density on Turbine Blade Platform Film-Cooling

2009 ◽  
Author(s):  
Diganta P. Narzary ◽  
Kuo-Chun Liu ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Flow Rate ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Mainstream Flow ◽  
Purge Flow

Detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform of a five-blade linear cascade. The parameters chosen were — freestream turbulence intensity, upstream stator-rotor purge flow rate, discrete-hole film-cooling blowing ratio, and coolant-to-mainstream density ratio. The measurement technique adopted was temperature sensitive paint (TSP) technique. Two turbulence intensities of 4.2% and 10.5%; three purge flows between the range of 0.25% and 0.75% of mainstream flow rate; three blowing ratios between 1.0 and 2.0; and three density ratios between 1.1 and 2.1 were investigated. Purge flow was supplied via a typical double-toothed stator-rotor seal, whereas the discrete-hole film cooling was accomplished via two rows of cylindrical holes arranged along the length of the platform. The inlet and the exit Mach numbers were 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 7.5*105 based on the exit velocity and chord length of the blade. Results indicated that platform film-cooling effectiveness decreased with turbulence intensity, increased with purge flow rate and density ratio, and possessed an optimum blowing ratio value. The improved effectiveness with density ratio was further validated by the pressure sensitive paint (PSP) technique.

Film Cooling Effectiveness Distributions on a Turbine Blade Cascade Platform With Stator-Rotor Purge and Discrete Film Hole Flows

2006 ◽  
Author(s):  
Lesley M. Wright ◽  
Sarah A. Blake ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Flow Rate ◽  
Film Cooling ◽  
Coolant Flow ◽  
Coolant Flow Rate ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Wide Range ◽  
Mainstream Flow ◽  
Purge Flow

An experimental investigation has been completed to obtain detailed film cooling effectiveness distributions on a cooled turbine blade platform within a linear cascade. The platform has a labyrinth-like seal upstream of the blades to model a realistic stator-rotor seal configuration. Additional coolant is supplied to the downstream half of the platform via discrete film cooling holes. The coolant flow rate through the upstream seal varies from 0.5% to 2.0% of the mainstream flow, while the blowing ratio of the coolant through the discrete holes varies from 0.5 to 2.0 (based on the mainstream velocity at the exit of the cascade). Detailed film cooling effectiveness distributions are obtained using the pressure sensitive paint (PSP) technique under a wide range of coolant flow conditions and various freestream turbulence levels (0.75% or 13.4%). The PSP technique clearly shows how adversely the coolant is affected by the passage induced flow. With only purge flow from the upstream seal, the coolant flow rate must exceed 1.5% of the mainstream flow in order to adequately cover the entire passage. However, if discrete film holes are used on the downstream half of the passage, the platform can be protected while using less coolant (i.e. the seal flow rate can be reduced).

Film Cooling Effectiveness Distributions on a Turbine Blade Cascade Platform With Stator-Rotor Purge and Discrete Film Hole Flows

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Lesley M. Wright ◽  
Sarah A. Blake ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Flow Rate ◽  
Film Cooling ◽  
Coolant Flow ◽  
Coolant Flow Rate ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Wide Range ◽  
Mainstream Flow ◽  
Purge Flow

An experimental investigation to obtain detailed film cooling effectiveness distributions on a cooled turbine blade platform within a linear cascade has been completed. The Reynolds number of the freestream flow is 3.1×105, and the platform has a labyrinthlike seal upstream of the blades to model a realistic stator-rotor seal configuration. An additional coolant is supplied to the downstream half of the platform via discrete film cooling holes. The coolant flow rate through the upstream seal varies from 0.5% to 2.0% of the mainstream flow, while the blowing ratio of the coolant through the discrete holes varies from 0.5 to 2.0 (based on the mainstream velocity at the exit of the cascade). Detailed film cooling effectiveness distributions are obtained using the pressure sensitive paint (PSP) technique under a wide range of coolant flow conditions and various freestream turbulence levels (0.75% or 13.4%). The PSP technique clearly shows how adversely the coolant is affected by the passage induced flow. With only purge flow from the upstream seal, the coolant flow rate must exceed 1.5% of the mainstream flow in order to adequately cover the entire passage. However, if discrete film holes are used on the downstream half of the passage, the platform can be protected while using less coolant (i.e., the seal flow rate can be reduced).

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Enhancement of Film Cooling Performance at the Leading Edge of Turbine Blade

2006 ◽  
Author(s):  
K.-S. Kim ◽  
Youn J. Kim ◽  
S.-M. Kim
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Cylindrical Body ◽  
Spanwise Direction ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

To enhance the film cooling performance in the vicinity of the turbine blade leading edge, the flow characteristics of the film-cooled turbine blade have been investigated using a cylindrical body model. The inclination of the cooling holes is along the radius of the cylindrical wall and 20 deg relative to the spanwise direction. Mainstream Reynolds number based on the cylinder diameter was 1.01×105 and 0.69×105, and the mainstream turbulence intensities were about 0.2% in both Reynolds numbers. CO2 was used as coolant to simulate the effect of density ratio of coolant-to-mainstream. Furthermore, the effect of coolant flow rates was studied for various blowing ratios of 0.4, 0.7, 1.1, and 1.4, respectively. In experiment, spatially-resolved temperature distributions along the cylindrical body surface were visualized using infrared thermography (IRT) in conjunction with thermocouples, digital image processing, and in situ calibration procedures. This comparison shows the results generated to be reasonable and physically meaningful. The film cooling effectiveness of current measurement (0.29 mm × 0.33 min per pixel) presents high spatial and temperature resolutions compared to other studies. Results show that the blowing ratio has a strong effect on film cooling effectiveness and the coolant trajectory is sensitive to the blowing ratio. The local spanwise-averaged effectiveness can be improved by locating the first-row holes near the second-row holes.

Effect of Upstream Wake With Vortex on Turbine Blade Platform Film Cooling With Simulated Stator-Rotor Purge Flow

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Lesley M. Wright ◽  
Sarah A. Blake ◽  
Dong-Ho Rhee ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Labyrinth Seal ◽  
Delta Wings ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Linear Cascade ◽  
Passage Vortex ◽  
Mainstream Flow ◽  
Purge Flow

Detailed film cooling effectiveness distributions were experimentally obtained on a turbine blade platform within a linear cascade. The film cooling effectiveness distributions were obtained on the platform with upstream disturbances used to simulate the passing vanes. Cylindrical rods, placed upstream of the blades, simulated the wake created by the trailing edge of the stator vanes. The rods were placed at four locations to show how the film cooling effectiveness was affected relative to the vane location. In addition, delta wings were placed upstream of the blades to model the effect of the passage vortex (generated in the vane passage) on the platform film cooling effectiveness. The delta wings create a vortex similar to the passage vortex as it exits the upstream vane passage. The film cooling effectiveness was measured with the delta wings placed at four location, to investigate the effect of the passing vanes. Finally, the delta wings were coupled with the cylindrical rods to examine the combined effect of the upstream wake and passage vortex on the platform film cooling effectiveness. The detailed film cooling effectiveness distributions were obtained using pressure sensitive paint in the five blade linear cascade. An advanced labyrinth seal was placed upstream of the blades to simulate purge flow from a stator-rotor seal. The coolant flow rate varied from 0.5% to 2.0% of the mainstream flow, while the Reynolds number of the mainstream flow remained constant at 3.1×105 (based on the inlet velocity and chord length of the blade). The film cooling effectiveness was not significantly affected with the upstream rod. However, the vortex generated by the delta wings had a profound impact on the film cooling effectiveness. The vortex created more turbulent mixing within the blade passage, and the result is reduced film cooling effectiveness through the entire passage. When the vane induced secondary flow is included, the need for additional platform cooling becomes very obvious.

Upstream Vortex Effects on Turbine Blade Platform Film Cooling With Typical Stator-Rotor Purge Flow

2007 ◽  
Author(s):  
Zhihong Gao ◽  
Diganta Narzary ◽  
Shantanu Mhetras ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Delta Wing ◽  
Delta Wings ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Passage Vortex ◽  
Mainstream Flow ◽  
Purge Flow

Detailed film cooling effectiveness distributions were experimentally obtained on a turbine blade platform within a five-blade linear cascade. A typical labyrinth-like seal was placed upstream of the cascade blades to simulate purge flow from a stator-rotor gap. Delta wings were periodically placed upstream of the blades to model the effect of the passage vortex generated in the vane passage on the downstream blade platform film cooling effectiveness. Typical vane passage vortex was simulated by two delta wings with height of 10% and 20% of the blade span, respectively. The strength of vane passage vortex was also modeled by varying the attack angle of mainstream to the delta wing. The film cooling effectiveness was measured with the delta wings placed at four phase locations, to investigate the effect of the passing vanes. The detailed film cooling effectiveness distributions on the platform were obtained using pressure sensitive paint (PSP) technique. The coolant mass flow rate varied from 0.25% to 1.0% of the mainstream flow. The freestream Reynolds number, based on the axial chord length and the exit velocity, was 750,000. The Mach numbers at the inlet and the exit were 0.27 and 0.44, respectively. The vortex generated by the delta wings had a profound impact on the platform film cooling effectiveness. The upstream vortex created more turbulent mixing within the blade passage and resulted in reduced film cooling effectiveness on the blade platform.

Effect of Density Ratio on Flat Plate Film Cooling With Shaped Holes Using PSP

2010 ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Michael D. Clemenson
Keyword(s):  
Flat Plate ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Density Ratio ◽  
Freestream Turbulence ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cylindrical Holes ◽  
Film Cooling Holes

Detailed film cooling effectiveness distributions are obtained on a flat plate using the pressure sensitive paint (PSP) technique. The applicability of the PSP technique is expanded to include a coolant-to-mainstream density ratio of 1.4. The effect of density ratio on the film cooling effectiveness is coupled with varying blowing ratio (M = 0.25–2.0), freestream turbulence intensity (Tu = 1%–12.5%), and film hole geometry. The effectiveness distributions are obtained on three separate flat plates containing either simple angle, cylindrical holes, simple angle, fanshaped holes (α = 10°), or simple angle, laidback, fanshaped holes (α = 10°, γ = 10°). In all three cases, the film cooling holes are angled at θ = 35° from the mainstream flow. Using the PSP technique, the combined effects of blowing ratio, turbulence intensity, and density ratio are captured for each film cooling geometry. The detailed film cooling effectiveness distributions, for cylindrical holes, clearly show the effectiveness at the lowest blowing ratio is enhanced at the lower density ratio (DR = 1). However, as the blowing ratio increases, a transition occurs, leading to increased effectiveness with the elevated density ratio (DR = 1.4). In addition, the PSP technique captures an upstream shift of the coolant jet reattachment point as the density ratio increases or the turbulence intensity increases (at moderate blowing ratios for cylindrical holes). With the decreased momentum of the shaped film cooling holes, the greatest film cooling effectiveness is obtained at the lower density ratio (DR = 1.0) over the entire range of blowing ratios considered. In all cases, as the freestream turbulence intensity increases, the film effectiveness decreases; this effect is reduced as the blowing ratio increases for all three film hole configurations.

Effect of Upstream Wake With Vortex on Turbine Blade Platform Film Cooling With Simulated Stator-Rotor Purge Flow

2007 ◽  
Author(s):  
Lesley M. Wright ◽  
Sarah A. Blake ◽  
Dong-Ho Rhee ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Labyrinth Seal ◽  
Delta Wings ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Linear Cascade ◽  
Passage Vortex ◽  
Mainstream Flow ◽  
Purge Flow

Detailed film cooling effectiveness distributions were experimentally obtained on a turbine blade platform within a linear cascade. The film cooling effectiveness distributions were obtained on the platform with upstream disturbances used to simulate the passing vanes. Cylindrical rods, placed upstream of the blades, simulated the wake created by the trailing edge of the stator vanes. The rods were placed at 4 locations to show how the film cooling effectiveness was affected relative to the vane location. In addition, delta wings were placed upstream of the blades to model the effect of the passage vortex (generated in the vane passage) on the platform film cooling effectiveness. The delta wings create a vortex similar to the passage vortex as it exits the upstream vane passage. The film cooling effectiveness was measured with the delta wings placed at 4 locations, to investigate the effect of the passing vanes. Finally, the delta wings were coupled with the cylindrical rods to examine the combined effect of the upstream wake and passage vortex on the platform film cooling effectiveness. The detailed film cooling effectiveness distributions were obtained using pressure sensitive paint (PSP) in the five blade linear cascade. An advanced labyrinth seal was placed upstream of the blades to simulate purge flow from a statorrotor seal. The coolant flow rate varied from 0.5% to 2.0% of the mainstream flow, while the Reynolds number of the mainstream flow remained constant at 3.1*105 (based on the inlet velocity and chord length of the blade). The film cooling effectiveness was not significantly affected with the upstream rod. However, the vortex generated by the delta wings had a profound impact on the film cooling effectiveness. The vortex created more turbulent mixing within the blade passage, and the result is reduced film cooling effectiveness through the entire passage. When the vane induced secondary flow is included, the need for additional platform cooling becomes very obvious.

Effect of Density Ratio on Flat Plate Film Cooling With Shaped Holes Using PSP

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Michael D. Clemenson
Keyword(s):  
Flat Plate ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Density Ratio ◽  
Freestream Turbulence ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cylindrical Holes ◽  
Film Cooling Holes

Detailed film-cooling effectiveness distributions are obtained on a flat plate using the pressure sensitive paint (PSP) technique. The applicability of the PSP technique is expanded to include a coolant-to-mainstream density ratio of 1.4. The effect of density ratio on the film-cooling effectiveness is coupled with varying blowing ratio (M=0.25–2.0), freestream turbulence intensity (Tu=1–12.5%), and film hole geometry. The effectiveness distributions are obtained on three separate flat plates containing either simple angle, cylindrical holes, simple angle, fanshaped holes (α=10 deg), or simple angle, laidback, fanshaped holes (α=10 deg and γ=10 deg). In all three cases, the film-cooling holes are angled at θ=35 deg from the mainstream flow. Using the PSP technique, the combined effects of blowing ratio, turbulence intensity, and density ratio are captured for each film-cooling geometry. The detailed film-cooling effectiveness distributions, for cylindrical holes, clearly show that the effectiveness at the lowest blowing ratio is enhanced at the lower density ratio (DR=1). However, as the blowing ratio increases, a transition occurs, leading to increased effectiveness with the elevated density ratio (DR=1.4). In addition, the PSP technique captures an upstream shift of the coolant jet reattachment point as the density ratio increases or the turbulence intensity increases (at moderate blowing ratios for cylindrical holes). With the decreased momentum of the shaped film-cooling holes, the greatest film-cooling effectiveness is obtained at the lower density ratio (DR=1.0) over the entire range of blowing ratios considered. In all cases, as the freestream turbulence intensity increases, the film effectiveness decreases; this effect is reduced as the blowing ratio increases for all three film hole configurations.

Sign in / Sign up

Export Citation Format

Share Document