Discussion: “An Experimental Study on Heat Transfer Surface Area of Wavy-Fin Heat Exchangers” [Asadi, M., and Xie, G., 2014, J. Therm. Sci. Eng. Appl., 6(3), 031012]

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
M. M. Awad
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Surface Area ◽  
Heat Exchangers ◽  
Heat Transfer Surface

scholarly journals Enhancement of heat exchangers with metal foams

2019 ◽  
Vol 9 (1) ◽  
pp. 15-28
Author(s):  
Mete Ozturk ◽  
Bahadır Dogan
Keyword(s):  
Heat Transfer ◽  
Surface Area ◽  
Heat Exchangers ◽  
Energy Demand ◽  
Emerging Technologies ◽  
Metal Foams ◽  
Heat Transfer Surface ◽  
Technological Equipment ◽  
Surface Areas

Removal of the heat is becoming a vital issue for safer operations of today’s technological equipment. The necessity of heat exchangers is underlined at this stage for the sake of the emerging technologies, which are producing more heat than before by the increment of the higher energy demand during their operations. Several methods have been suggested to improve the efficiency of the heat exchangers in last decades by the researchers including the extension of the heat transfer surface by the larger surface areas surrounding the channels. In addition to this fundamental approach (extension of the surface area), alternate methods have been released too including the implementation of metal foams to the heat exchangers as for the extension of the surface. Keywords: Heat exchangers, surface extension, metal foams.

Failure Analysis of Heat Exchangers

2021 ◽  
pp. 3-19
Author(s):  
Dusan P. Sekulic
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Failure Analysis ◽  
Thermal Energy ◽  
Solid Surface ◽  
Heat Exchangers ◽  
Heat Transfer Surface ◽  
Tubular Heat Exchanger ◽  
Erosion Corrosion ◽  
Different Temperatures

Abstract Heat exchangers are devices used to transfer thermal energy between two or more fluids, between a solid surface and a fluid, or between a solid particulate and a fluid at different temperatures. This article first addresses the causes of failures in heat exchangers. It then provides a description of heat-transfer surface area, discussing the design of the tubular heat exchanger. Next, the article discusses the processes involved in the examination of failed parts. Finally, it describes the most important types of corrosion, including uniform, galvanic, pitting, stress, and erosion corrosion.

Finned Elliptical Tubes and Their Application in Air-Cooled Heat Exchangers

1966 ◽  
Vol 88 (2) ◽  
pp. 179-186 ◽  
Author(s):  
Franz J. Schulenberg
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Heat Transfer Surface ◽  
Great Success ◽  
Sufficient Criterion ◽  
Tube Heat Exchanger ◽  
Circular Tubes ◽  
Fin Tube

Finned circular tubes have been used exclusively in air-cooled heat exchangers built for the American petroleum and chemical industries. In Europe, however, other tube geometries, in particular, finned elliptical tubes, have been used with great success. In this paper, the theory of the finned elliptical tube and its application in air-cooled heat exchangers are discussed. Finned circular and elliptical tubes are compared; it is shown that the developed heat transfer surface alone is not a sufficient criterion for predicting the performance of an air-cooled fin-tube heat exchanger.

Comparative Experimental Study on Performance of Corrugated Tube and Straight Tube Heat Exchanger

2012 ◽  
Vol 560-561 ◽  
pp. 156-160
Author(s):  
Lin Ping Lu ◽  
Liang Ying
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Straight Tube ◽  
Lower Stress ◽  
Shell Side ◽  
Tube Heat Exchanger ◽  
Corrugated Tube

The experiments on heat transfer coefficient, pressure drop and thermal stress were done to heat exchangers with corrugated tubes and staight tubes. By analyising and comparing the heat transfer coeffient, pressure drop in tube side and shell side and axial force and stress, some conclusions can be conducted that the corrugated tube heat exchanger has better heat transfer coeffient, higher pressure drop and much lower stress caused by temperatur difference, also, it has obvious advantages under the circumstance of low Reynolds number and high temperature difference.

Crystallization Fouling in Plate Heat Exchangers

1993 ◽  
Vol 115 (3) ◽  
pp. 584-591 ◽  
Author(s):  
B. Bansal ◽  
H. Mu¨ller-Steinhagen
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Flow Velocity ◽  
Wall Temperature ◽  
Heat Exchangers ◽  
Calcium Sulfate ◽  
Surface Reaction ◽  
Heat Transfer Surface ◽  
Plate Heat

Crystallization fouling of calcium sulfate was investigated in a plate and frame heat exchanger. The effects of flow velocity, wall temperature, and CaSO4, concentration on the fouling rates have been investigated and the distribution of scale along the heat transfer surface has been observed. The measured fouling curves are compared with predictions from a surface reaction controlled model.

Sign in / Sign up

Export Citation Format

Share Document