Performance Study of Continuous Helical Baffle Shell and Tube Heat Exchanger With Central Low-Pressure Regions

2016 ◽  
Vol 8 (3) ◽  
Author(s):  
Partha Pratim Saikia ◽  
Abhik Majumder
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Low Pressure ◽  
Performance Study ◽  
Contact Heat ◽  
Indirect Contact ◽  
Tube Heat Exchanger ◽  
Helical Baffle ◽  
Shell And Tube

Shell and tube heat exchanger (STHX) is a class of indirect contact heat exchangers which has wide applications in various industries. In this paper, the shell-side performance characteristics of a small STHX with differently notched continuous helical baffle (CHB) geometries are numerically studied and compared with same CHB without notched regions. The indentations are uniquely produced by placing the notch near the core of the heat exchanger, thereby conferring the flow with low-pressure drop regions. Two set of models of inner notched continuous helical baffle (ICHB), i.e., ICHB1 and ICHB2, are studied with notch width of about 5% and 10% of the inner shell diameter of the same heat exchanger. In comparison with the CHBSTHX, it is seen that the STHXs incorporated with ICHBs, the heat transfer rate dropped slightly, but a significant decrease in pressure drop is observed. It is found that the heat transfer coefficient to pressure drop ratio for ICBH1 and ICHB2 shows significant increase in comprehensive performance of about 3.5% and 32.42%, respectively, when compared with same CHB without notched regions.

Improving shell and tube heat exchanger thermohydraulic performance using combined baffle

2019 ◽  
Vol 30 (8) ◽  
pp. 4119-4140 ◽  
Author(s):  
Ali Akbar Abbasian Arani ◽  
Hamed Uosofvand
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Fluid Dynamic ◽  
Flow Simulation ◽  
Content Type ◽  
Tube Heat Exchanger ◽  
Flow And Heat Transfer ◽  
Helical Baffle ◽  
Shell And Tube

Purpose This paper aims to investigate the fluid flow and heat transfer of a laboratory shell and tube heat exchanger that are analyzed using computational fluid dynamic approach by SOLIDWORKS flow simulation (ver. 2015) software. Design/methodology/approach In this study, several types of baffle including segmental baffle, butterfly baffle, helical baffle, combined helical-segmental baffle, combined helical-disk baffle and combined helical-butterfly baffle are examined. Two important parameters as the heat transfer and pressure drop are evaluated and analyzed. Based on obtained results, segmental baffle has the highest amount of heat transfer and pressure drop. To assess the integrative performance, performance coefficient defines as “Q/Δp” is used. Findings This investigation showed that among the presented baffle types, the heat exchangers equipped with disk baffle has the highest heat transfer. In addition, in the same mass flow rate, the performance coefficient of the shell and tube heat exchanger equipped with helical-butterfly baffle is the highest among the proposed models. Originality/value After combined helical-butterfly baffle the butterfly baffle, disk baffle, helical-segmental baffle and helical-disk baffle show their superiority of 35.12, 25, 22 and 12 per cent rather than the common segmental baffle, respectively. Furthermore, except for the combined helical-disk baffle, the other type of combined baffle have better performance compare to the basic configuration (butterfly and segmental baffle).

Numerical simulation of the effect of baffle cut and baffle spacing on shell side heat exchanger performance using CFD

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Swanand Gaikwad ◽  
Ashish Parmar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Numerical Results ◽  
Shell Side ◽  
Tube Heat Exchanger ◽  
Shell And Tube ◽  
Two Parameters

AbstractHeat exchangers possess a significant role in energy transmission and energy generation in most industries. In this work, a three-dimensional simulation has been carried out of a shell and tube heat exchanger (STHX) consisting of segmental baffles. The investigation involves using the commercial code of ANSYS CFX, which incorporates the modeling, meshing, and usage of the Finite Element Method to yield numerical results. Much work is available in the literature regarding the effect of baffle cut and baffle spacing as two different entities, but some uncertainty pertains when we discuss the combination of these two parameters. This study aims to find an appropriate mix of baffle cut and baffle spacing for the efficient functioning of a shell and tube heat exchanger. Two parameters are tested: the baffle cuts at 30, 35, 40% of the shell-inside diameter, and the baffle spacing’s to fit 6,8,10 baffles within the heat exchanger. The numerical results showed the role of the studied parameters on the shell side heat transfer coefficient and the pressure drop in the shell and tube heat exchanger. The investigation shows an increase in the shell side heat transfer coefficient of 13.13% when going from 6 to 8 baffle configuration and a 23.10% acclivity for the change of six baffles to 10, for a specific baffle cut. Evidence also shows a rise in the pressure drop with an increase in the baffle spacing from the ranges of 44–46.79%, which can be controlled by managing the baffle cut provided.

Experimental Investigation of Heat Transfer Enhancement of Shell and Tube Heat Exchanger Using SnO2-Water and Ag-Water Nanofluids

2019 ◽  
Vol 12 (4) ◽  
Author(s):  
S. V. Sridhar ◽  
R. Karuppasamy ◽  
G. D. Sivakumar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer Coefficient ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Abstract In this investigation, the performance of the shell and tube heat exchanger operated with tin nanoparticles-water (SnO2-W) and silver nanoparticles-water (Ag-W) nanofluids was experimentally analyzed. SnO2-W and Ag-W nanofluids were prepared without any surface medication of nanoparticles. The effects of volume concentrations of nanoparticles on thermal conductivity, viscosity, heat transfer coefficient, fiction factor, Nusselt number, and pressure drop were analyzed. The results showed that thermal conductivity of nanofluids increased by 29% and 39% while adding 0.1 wt% of SnO2 and Ag nanoparticles, respectively, due to the unique intrinsic property of the nanoparticles. Further, the convective heat transfer coefficient was enhanced because of improvement of thermal conductivity of the two phase mixture and friction factor increased due to the increases of viscosity and density of nanofluids. Moreover, Ag nanofluid showed superior pressure drop compared to SnO2 nanofluid owing to the improvement of thermophysical properties of nanofluid.

3-D Numerical Study on Shell-Side Comprehensive Performance of Shell-and-Tube Heat Exchanger With Combined Helical Baffles

2010 ◽  
Author(s):  
Guidong Chen ◽  
Jing Xu ◽  
Ming Zen ◽  
Qiuwang Wang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Shell Side ◽  
Tube Heat Exchanger ◽  
Comprehensive Performance ◽  
Shell And Tube ◽  
The Heat Transfer Coefficient

In order to improve heat transfer performance of conventional segmental baffled shell-and-tube heat exchangers (STHXs), the shell-and-tube heat exchanger with combined helical baffles (CMH-STHX) were invented. In the present study, the CMH-STHX is compared with three other STHXs which were set up with continuous helical baffles (CH-STHX), discontinuous helical baffles (DCH-STHX) and segmental baffles (SG-STHX), by Computational Fluid Dynamics method. The numerical results show that, for the same mass flow rate at the shell side, the overall pressure drop of the CMH-STHX is about 50% and 40% lower than that of SG-STHX and CH-STHX. The heat transfer coefficient of the CMH-STHX is between those of CH-STHX and DCH-STHX and it is 6.3% lower than that of SG-STHX. The heat transfer coefficient under unit pressure drop h/Δp is introduced to evaluate the comprehensive performance of STHXs. The h/Δp of the CMH-STHX is 7.5%, 6.5% and 87.4% higher on average than those of the CH-SHTX, DCH-STHX and SG-STHX. Furthermore, the total heat transfer rate of CMH-STHX is about 25% higher than that of SG-STHX for the same total pressure drop of shell side. Supported by these results, the new heat exchanger (CMH-STHX) may be used to replace the conventional shell-and-tube heat exchanger in industrial applications.

Design optimization of a shell and tube heat exchanger with staggered baffles using neural network and genetic algorithm

2021 ◽  
pp. 095440622110057
Author(s):  
Kizhakke Kodakkattu Saijal ◽  
Thondiyil Danish
Keyword(s):  
Heat Transfer ◽  
Genetic Algorithm ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Orientation Angle ◽  
Design Parameters ◽  
Outer Diameter ◽  
Maximum Heat ◽  
Tube Heat Exchanger ◽  
Shell And Tube

A shell and tube heat exchanger with staggered baffles (STHX-ST) is designed by integrating the features of both segmental and helical baffles, which produces a helical flow in the shell side. This work studies the effect of different parameters on the performance of the STHX-ST through numerical analysis. Shell inner diameter, tube outer diameter, baffle cut, baffle spacing, and baffle orientation angle are the design parameters. Multi-objective optimization using genetic algorithm (GA) is carried out to maximize the heat transfer rate while minimizing the pressure drop. The objective functions for optimization are approximated using artificial neural networks (ANNs). The training data for ANNs are simulated from CFD analysis as per the Taguchi orthogonal test table. The optimal solution obtained from the Pareto front has a maximum heat transfer of 154555 W for a minimum pressure drop of 88083.86 Pa.

scholarly journals Design and Analysis of double- stacked Heat Exchanger for Brewery Application

2020 ◽  
Vol 9 (1) ◽  
pp. 1793-1798
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Flow Rate ◽  
Transfer Rate ◽  
Working Fluid ◽  
Support Weight ◽  
Tube Heat Exchanger ◽  
Shell And Tube

A heat exchanger is a device intensively used for enhancing the transfer of heat energy between two or more working fluids at different temperature, which are in thermal contact. The optimal design and efficient operation of heat exchanger and heat transfer network are of a great significance in any of the process industry. The heat transfer efficiency depends on both design of heat exchanger and property of working fluid. From various types of heat exchanger, the double stacked shell and tube heat exchanger with straight tube and single pass is to be under study. Here the redesign of heat exchanger takes place with the key objectives of optimizing the pressure drop, optimizing the heat transfer rate and reducing the saddle support weight used for cooling purpose in brewery application. The design calculations are carried out using the Kerns and Bell Delwar method and other important parameters dealing with material selection and geometries are also taken into consideration. FEA analysis for optimizing the saddle support weight is carried out using Dassault systeme’s Solidworks while the CFD analysis for optimizing pressure drop and heat transfer rate is carried out using Dassault systeme’s Solidworks analysis software and the design and working of Shell and tube heat exchanger is determined in terms of variables such as pressure ,temperature ,mass flow rate ,flow rate ,energy input output that are of particular interest in Shell and tube heat exchanger analysis.

Sign in / Sign up

Export Citation Format

Share Document