Prediction of Ultra-Lean Spark Ignition Engine Performances by Quasi-Dimensional Combustion Model With a Refined Laminar Flame Speed Correlation

2020 ◽  
Vol 143 (3) ◽  
Author(s):  
Ratnak Sok ◽  
Kyohei Yamaguchi ◽  
Jin Kusaka
Keyword(s):  
Gasoline Engine ◽  
Laminar Flame ◽  
Flame Speed ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Laminar Flame Speed ◽  
Gasoline Engines ◽  
Indicated Mean Effective Pressure ◽  
Constant Volume Chamber ◽  
Good Agreement

Abstract The turbulent combustion in gasoline engines is highly dependent on laminar flame speed SL. A major issue of the quasi-dimensional (QD) combustion model is an accurate prediction of the SL, which is unstable under low engine speeds and ultra-lean mixture. This work investigates the applicability of the combustion model with a refined SL correlation for evaluating the combustion characteristics of a high-tumble port gasoline engine operated under ultra-lean mixtures. The SL correlation is modified and validated for a five-component gasoline surrogate. Predicted SL values from the conventional and refined functions are compared with measurements taken from a constant-volume chamber under micro-gravity conditions. The SL data are measured at reference and elevated conditions. The results show that the conventional SL overpredicts the flame speeds under all conditions. Moreover, the conventional model predicts negative SL at equivalence ratio ϕ ≤ 0.3 and ϕ ≥ 1.9, while the revised SL is well validated against the measurements. The improved SL correlation is incorporated into the QD combustion model by a user-defined function. The engine data are measured at 1000–2000 rpm under engine load net indicated mean effective pressure (IMEPn) = 0.4–0.8 MPa and ϕ = 0.5. The predicted engine performances and combustions are well validated with the measured data, and the model sensitivity analysis also shows a good agreement with the engine experiments under cycle-by-cycle variations.

scholarly journals Impact of the laminar flame speed correlation on the results of a quasi-dimensional combustion model for Spark-Ignition engine

2018 ◽  
Vol 148 ◽  
pp. 631-638 ◽  
Author(s):  
L. Teodosio ◽  
F. Bozza ◽  
D. Tufano ◽  
P. Giannattasio ◽  
E. Distaso ◽  
...  
Keyword(s):  
Laminar Flame ◽  
Spark Ignition ◽  
Flame Speed ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Laminar Flame Speed

Laminar flame speed correlations for methane, ethane, propane and their mixtures, and natural gas and gasoline for spark-ignition engine simulations

2017 ◽  
Vol 18 (9) ◽  
pp. 951-970 ◽  
Author(s):  
Riccardo Amirante ◽  
Elia Distaso ◽  
Paolo Tamburrano ◽  
Rolf D Reitz
Keyword(s):  
Natural Gas ◽  
Laminar Flame ◽  
Spark Ignition ◽  
Flame Speed ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Computational Time ◽  
Laminar Flame Speed ◽  
Spark Ignition Engines ◽  
Empirical Correlations

The laminar flame speed plays an important role in spark-ignition engines, as well as in many other combustion applications, such as in designing burners and predicting explosions. For this reason, it has been object of extensive research. Analytical correlations that allow it to be calculated have been developed and are used in engine simulations. They are usually preferred to detailed chemical kinetic models for saving computational time. Therefore, an accurate as possible formulation for such expressions is needed for successful simulations. However, many previous empirical correlations have been based on a limited set of experimental measurements, which have been often carried out over a limited range of operating conditions. Thus, it can result in low accuracy and usability. In this study, measurements of laminar flame speeds obtained by several workers are collected, compared and critically analyzed with the aim to develop more accurate empirical correlations for laminar flame speeds as a function of equivalence ratio and unburned mixture temperature and pressure over a wide range of operating conditions, namely [Formula: see text], [Formula: see text] and [Formula: see text]. The purpose is to provide simple and workable expressions for modeling the laminar flame speed of practical fuels used in spark-ignition engines. Pure compounds, such as methane and propane and binary mixtures of methane/ethane and methane/propane, as well as more complex fuels including natural gas and gasoline, are considered. A comparison with available empirical correlations in the literature is also provided.

A Laminar Burning Velocity Correlation for Hydrogen/Air Mixtures Valid at Spark-Ignition Engine Conditions

2003 ◽  
Author(s):  
Sebastian Verhelst ◽  
Roger Sierens
Keyword(s):  
Chemical Kinetics ◽  
Laminar Flame ◽  
Burning Velocity ◽  
Spark Ignition ◽  
Flame Speed ◽  
Spark Ignition Engine ◽  
Laminar Flame Speed ◽  
Spark Ignition Engines ◽  
Laminar Burning Velocity ◽  
Velocity Correlation

During the development of a quasi-dimensional simulation programme for the combustion of hydrogen in spark-ignition engines, the lack of a suitable laminar flame speed formula for hydrogen/air mixtures became apparent. A literature survey shows that none of the existing correlations covers the entire temperature, pressure and mixture composition range as encountered in spark-ignition engines. Moreover, there is ambiguity concerning the pressure dependence of the laminar burning velocity of hydrogen/air mixtures. Finally, no data exists on the influence of residual gases. This paper looks at several reaction mechanisms found in the literature for the kinetics of hydrogen/oxygen mixtures, after which one is selected that corresponds best with available experimental data. An extensive set of simulations with a one-dimensional chemical kinetics code is performed to calculate the laminar flame speed of hydrogen/air mixtures, in a wide range of mixture compositions and initial pressures and temperatures. The use of a chemical kinetics code permits the calculation of any desired set of conditions and enables the estimation of interactions, e.g. between pressure and temperature effects. Finally, a laminar burning velocity correlation is presented, valid for air-to-fuel equivalence ratios λ between 1 and 3 (fuel-to-air equivalence ratio 0.33 < φ < 1), initial pressures between 1 bar and 16 bar, initial temperatures between 300 K and 800 K and residual gas fractions up to 30 vol%. These conditions are sufficient to cover the entire operating range of hydrogen fuelled spark-ignition engines.

An Experimental and Modeling Study of Laminar Flame Speeds of Alternative Aviation Fuels

2011 ◽  
Author(s):  
Thomas Kick ◽  
Trupti Kathrotia ◽  
Marina Braun-Unkhoff ◽  
Uwe Riedel
Keyword(s):  
Laminar Flame ◽  
Cone Angle ◽  
Reaction Model ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Alternative Aviation Fuels ◽  
Predicted Values ◽  
Angle Method ◽  
Eu Project ◽  
Good Agreement

The present work reports on measurements of burning velocities of synthetic fuel air mixtures exploiting the cone-angle method, as part of the EU project ALFA-BIRD. The GtL (Gas-to-Liquid)-air mixtures — (i) 100% GtL and (ii) GtL+20% hexanol, respectively — were studied at atmospheric pressure, with values of the equivalence ratio φ ranging between φ ∼ 1.0 and φ ∼ 1.3, at preheat temperatures To = 423 K (GtL+20% hexanol) as well as To = 473 K (for 100% GtL and GtL+20% hexanol). A comparison between experimentally obtained burning velocities and predicted values of laminar flame speed is presented, too. In general, good agreement was found between predicted and measured data for the range of conditions considered in the present study. The predictive capability of the detailed reaction model consisting of 3479 reactions involving 490 species will be discussed focusing on the laminar flame speed and the combustion of the components (n-decane, iso-octane, and 1-hexanol) of the surrogate used.

scholarly journals A quasi-dimensional model for hydrogen-enriched gasoline engines with a new laminar flame speed expression

2014 ◽  
Vol 61 ◽  
pp. 327-330 ◽  
Author(s):  
Xiaolong Liu ◽  
Changwei Ji ◽  
Binbin Gao ◽  
Shuofeng Wang ◽  
Jinxin Yang
Keyword(s):  
Laminar Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Dimensional Model ◽  
Gasoline Engines

Three-dimensional computational fluid dynamics simulation of hydrogen engines using a turbulent flame speed closure combustion model

2012 ◽  
Vol 13 (5) ◽  
pp. 464-481 ◽  
Author(s):  
Udo Gerke ◽  
Konstantinos Boulouchos
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Three Dimensional ◽  
Flame Speed ◽  
Combustion Model ◽  
Laminar Flame Speed ◽  
Release Rates ◽  
Turbulent Flame Speed

The mixture formation and combustion process of a hydrogen direct-injection internal combustion engine is computed using a modified version of a commercial three-dimensional computational fluid dynamics code. The aim of the work is the evaluation of hydrogen laminar flame speed correlations and turbulent flame speed closures with respect to combustion of premixed and stratified mixtures at various levels of air-to-fuel equivalence ratio. Heat-release rates derived from in-cylinder pressure traces are used for the validation of the combustion simulations. A turbulent combustion model with closures for a turbulent flame speed is investigated. The value of the computed heat-release rates mainly depends on the quality of laminar burning velocities and standard of turbulence quantities provided to the combustion model. Combustion simulations performed with experimentally derived laminar flame speed data give better results than those using laminar flame speeds obtained from a kinetic scheme. However, experimental data of hydrogen laminar flame speeds found in the literature are limited regarding the range of pressures, temperatures and air-to-fuel equivalence ratios, and do not comply with the demand of high-pressure engine-relevant conditions.

Prediction of Ultra-Lean SI Engine Performance by QD-Combustion Model With an Improved Laminar Flame Speed

2020 ◽  
Author(s):  
Ratnak Sok ◽  
Jin Kusaka ◽  
Kyohei Yamaguchi
Keyword(s):  
Gasoline Engine ◽  
Laminar Flame ◽  
Burning Velocity ◽  
Turbulent Flame ◽  
Combustion Process ◽  
Combustion Characteristics ◽  
Flame Speed ◽  
Combustion Model ◽  
Lean Mixture ◽  
Turbulent Flame Speed

Abstract A quasi-dimensional (QD) simulation model is a preferred method to predict combustion in the gasoline engines with reliable results and shorter calculation time compared with multi-dimensional simulation. The combustion phenomena in spark ignition (SI) engines are highly turbulent, and at initial stage of the combustion process, turbulent flame speed highly depends on laminar burning velocity SL. A major parameter of the QD combustion model is an accurate prediction of the SL, which is unstable under low engine speed and ultra-lean mixture. This work investigates the applicability of the combustion model for evaluating the combustion characteristics of a high-tumble port gasoline engine operated under ultra-lean mixture (equivalence ratio up to ϕ = 0.5) which is out of the range of currently available SL functions initially developed for a single component fuel. In this study, the SL correlation is improved for a gasoline surrogate fuel (5 components). Predicted SL data from the conventional and improved functions are compared with experimental SL data taken from a constant-volume chamber under micro-gravity condition. The SL measurements are done at reference conditions at temperature of 300K, pressure of 0.1MPaa, and at elevated conditions whose temperature = 360K, pressure = 0.1, 0.3, and 0.5 MPaa. Results show that the conventional SL model over-predicts flame speeds under all conditions. Moreover, the model predicts negative SL at very lean (ϕ ≤ 0.3) and rich (ϕ ≥ 1.9) mixture while the revised SL is well validated with the measured data. The improved SL formula is then incorporated into the QD combustion model by a user-defined function in GT-Power simulation. The engine experimental data are taken at 1000 RPM and 2000 RPM under engine load IMEPn = 0.4–0.8 MPa (with 0.1 increment) and ϕ ranges are up to 0.5. The results shows that the simulated engine performances and combustion characteristics are well validated with the experiments within 6% accuracy by using the QD combustion model coupled with the improved SL. A sensitivity analysis of the model is also in good agreement with the experiments under cyclic variation (averaged cycle, high IMEP or stable cycle, and low IMEP or unstable cycle).

Sign in / Sign up

Export Citation Format

Share Document