Energy, Exergy, Environmental (3E) and Parametric Assessment of a Triple-Pressure Reheat Combined-Cycle Power Plant

2021 ◽  
Vol 143 (11) ◽  
Author(s):  
Mohammadreza Babaei Jamnani ◽  
David S-K Ting ◽  
Rupp Carriveau ◽  
Amin Kardgar
Keyword(s):  
Power Plant ◽  
Heat Recovery ◽  
Flame Temperature ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Combined Cycle Power Plant ◽  
Environmental Objectives ◽  
Mass Flowrate ◽  
Mass Flow Rates ◽  
Reheating Process

Abstract In this study, energy, exergy, and environmental (3E) assessments have been conducted on a proposed combined-cycle power plant (CCPP) with three pressure levels of the HRSG and reheating process. 3E design approaches cross-link mechano-electric and environmental objectives. Herewith, the suggested combined-cycle is formed by a gas unit, condenser, steam turbines, triple-pressure heat recovery steam generator (HRSG) and also utilizes reheat facilities and auxiliary components. It is observed that more than 56% of total exergy destruction occurs in the combustor, followed by HRSG (15.29%), steam turbines (roughly 15.02%), gas turbine (8.93%), air compressor (1.79%), and condenser (0.66%). A parametric study is also presented that examines the sensitivity of performance indicators to various environmental states, steam pressures, pinch points, and steam mass flow rates. Moreover, it is presented that the implementation of Siemens SGT-100-1S over other GT configurations can considerably reduce deficiency of the overall cycle. The effects of each contaminant mass flowrate (NOx, CO, UHC, and CO2) and adiabatic flame temperature (AFT) are also studied when the gas unit operates under partial power and incomplete combustion conditions. In conclusion, a number of potential causes of irreversibilities and corrective optimization guidance are offered for each main equipment of the CCPP.

Simulation and Optimization of Combined Cycle Power Cycles Through HRSG’s Heat Exchangers Arrangement and Parameters for Exergy and Cost

2012 ◽  
Author(s):  
Ravin G. Naik ◽  
Chirayu M. Shah ◽  
Arvind S. Mohite
Keyword(s):  
Power Plant ◽  
Steam Generator ◽  
Heat Exchangers ◽  
Heat Recovery ◽  
Second Law Of Thermodynamics ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Exergetic Efficiency ◽  
Power Cycles ◽  
Combined Cycle Power Plant

To produce the power with higher overall efficiency and reasonable cost is ultimate aim for the power industries in the power deficient scenario. Though combined cycle power plant is most efficient way to produce the power in today’s world, rapidly increasing fuel prices motivates to define a strategy for cost-effective optimization of this system. The heat recovery steam generator is one of the equipment which is custom made for combined cycle power plant. So, here the particular interest is to optimize the combined power cycle performance through optimum design of heat recovery steam generator. The case of combined cycle power plant re-powered from the existing Rankine cycle based power plant is considered to be simulated and optimized. Various possible configuration and arrangements for heat recovery steam generator has been examined to produce the steam for steam turbine. Arrangement of heat exchangers of heat recovery steam generator is optimized for bottoming cycle’s power through what-if analysis. Steady state model has been developed using heat and mass balance equations for various subsystems to simulate the performance of combined power cycles. To evaluate the performance of combined power cycles and its subsystems in the view of second law of thermodynamics, exergy analysis has been performed and exergetic efficiency has been determined. Exergy concepts provide the deep insight into the losses through subsystems and actual performance. If the sole objective of optimization of heat recovery steam generator is to increase the exergetic efficiency or minimizing the exergy losses then it leads to the very high cost of power which is not acceptable. The exergo-economic analysis has been carried to find the cost flow from each subsystem involved to the combined power cycles. Thus the second law of thermodynamics combined with economics represents a very powerful tool for the systematic study and optimization of combined power cycles. Optimization studies have been carried out to evaluate the values of decision parameters of heat recovery steam generator for optimum exergetic efficiency and product cost. Genetic algorithm has been utilized for multi-objective optimization of this complex and nonlinear system. Pareto fronts generated by this study represent the set of best solutions and thus providing a support to the decision-making.

HRSG Duct Firing Revisited

2018 ◽  
Author(s):  
S. Can Gülen
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Fossil Fuel ◽  
Heat Rate ◽  
Combined Cycle ◽  
Efficiency Improvement ◽  
Combined Cycle Power Plant

Duct firing in the heat recovery steam generator (HRSG) of a gas turbine combined cycle power plant is a commonly used method to increase output on hot summer days when gas turbine airflow and power output lapse significantly. The aim is to generate maximum possible power output when it is most needed (and, thus, more profitable) at the expense of power plant heat rate. In this paper, using fundamental thermodynamic arguments and detailed heat and mass balance simulations, it will be shown that, under certain boundary conditions, duct firing in the HRSG can be a facilitator of efficiency improvement as well. When combined with highly-efficient aeroderivative gas turbines with high cycle pressure ratios and concomitantly low exhaust temperatures, duct firing can be utilized for small but efficient combined cycle power plant designs as well as more efficient hot-day power augmentation. This opens the door to efficient and agile fossil fuel-fired power generation opportunities to support variable renewable generation.

Optimization of Waste Heat Recovery Boiler of a Combined Cycle Power Plant

1996 ◽  
Vol 118 (3) ◽  
pp. 561-564 ◽  
Author(s):  
B. Seyedan ◽  
P. L. Dhar ◽  
R. R. Gaur ◽  
G. S. Bindra
Keyword(s):  
Power Plant ◽  
Optimum Design ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Combined Cycle ◽  
Heat Recovery Boiler ◽  
Combined Cycle Power Plant ◽  
Recovery Boiler

In the present work a procedure for optimum design of waste heat recovery boiler of a combined cycle power plant has been developed. This method enables the optimization of waste heat recovery boiler independent of the rest of the system and the design thus obtained can directly be employed in an existing plant.

Exergoeconomic Analysis of a Combined Cycle of Three Levels of Pressure

2016 ◽  
Author(s):  
Edgar Vicente Torres González ◽  
Raúl Lugo-Leyte ◽  
Martín Salazar-Pereyra ◽  
Miguel Toledo Velázquez ◽  
Helen Denise Lugo-Méndez ◽  
...  
Keyword(s):  
Power Plant ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Systematic Approach ◽  
Combined Cycle ◽  
Exergetic Efficiency ◽  
Steam Generators ◽  
Combined Cycle Power Plant ◽  
Exergoeconomic Analysis ◽  
The Cost

This paper presents an exergoeconomic analysis of the combined cycle power plant Tuxpan II located in Mexico. The plant is composed of two identical modules conformed by two gas turbines generating the required work and releasing the hot exhaust gases in two heat recovery steam generators. These components generate steam at three different pressure levels, used to produce additional work in one steam turbine. The productive structure of the considered system is used to visualize the cost formation process as well as the productive interaction between their components. The exergoeconomic analysis is pursued by 1) carrying out a systematic approach, based on the Fuel-Product methodology, in each component of the system; and 2) generating a set of equations, which allows compute the exergetic and exergoeconomic costs of each flow. The thermal and exergetic efficiency of the two gas turbines delivering 278.4 MW are 35.16% and 41.90% respectively. The computed thermal efficiency of the steam cycle providing 80.96 MW is 43.79%. The combined cycle power plant generates 359.36 MW with a thermal and exergetic efficiency of 47.27% and 54.10% respectively.

scholarly journals Thermodynamic analysis of heat recovery steam generator in combined cycle power plant

2007 ◽  
Vol 11 (4) ◽  
pp. 143-156 ◽  
Author(s):  
Kumar Ravi ◽  
Krishna Rama ◽  
Rama Sita
Keyword(s):  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Generator ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Combined Cycle Power Plant ◽  
Pressure Steam ◽  
Turbine Output

Combined cycle power plants play an important role in the present energy sector. The main challenge in designing a combined cycle power plant is proper utilization of gas turbine exhaust heat in the steam cycle in order to achieve optimum steam turbine output. Most of the combined cycle developers focused on the gas turbine output and neglected the role of the heat recovery steam generator which strongly affects the overall performance of the combined cycle power plant. The present paper is aimed at optimal utilization of the flue gas recovery heat with different heat recovery steam generator configurations of single pressure and dual pressure. The combined cycle efficiency with different heat recovery steam generator configurations have been analyzed parametrically by using first law and second law of thermodynamics. It is observed that in the dual cycle high pressure steam turbine pressure must be high and low pressure steam turbine pressure must be low for better heat recovery from heat recovery steam generator.

scholarly journals Combined Cycle Power Plant Start-Up Effects and Constraints of the HRSG

1992 ◽  
Author(s):  
Akber Pasha
Keyword(s):  
Power Plant ◽  
Conceptual Design ◽  
Steam Generator ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Combined Cycle Power Plant ◽  
System A ◽  
Start Up ◽  
Total Plant

The heat recovery steam generator (HRSG) is an integral part of the combined cycle power plant which includes combustion turbine and steam turbine in addition to heat recovery steam generator. The start-up of the heat recovery steam generator, therefore, has an influence on the start-up of the total plant. The paper discusses various constraints, both external and internal, which affect the Steam Generator start-up and in turn influence the start-up of the total plant. Considerations in the design of the steam generator to accommodate the plant start-up requirements, along with the effect of the cyclic or base loaded operation are also discussed. The paper also presents a procedure which may be adopted in the conceptual design of the plant for an optimized system, a system which can accommodate the total plant start-up requirements without undue constraints on the availability of the full plant output.

Sign in / Sign up

Export Citation Format

Share Document