Finite Element Analysis and Design of a Trochoidal-Type Machine Without Apex Seals

1995 ◽  
Author(s):  
Kannan Venkatesh ◽  
John B. Shung
Keyword(s):  
Finite Element ◽  
Iterative Procedure ◽  
Element Model ◽  
Design Parameters ◽  
Dimensional Model ◽  
Element Analysis ◽  
Analysis And Design ◽  
Type Machine ◽  
Free Body ◽  
The Finite Element Model

Abstract A two-dimensional model for a trochoidal-type machine without apex seals using finite element method has been developed with the help of Cosmos/M V1.65, and is evaluated by using a classical free-body technique. The minimum running clearance required to avoid contact between rotor and chamber is determined by an iterative procedure using the finite element model. The variation in the minimum required running clearance with the variation in the design parameters is studied. Guidelines for using the results of this study for an optimal design of a trochoidal-type machine without apex seals are presented.

Finite Element Analysis and Design of a Trochoidal-Type Machine Without Apex Seals

1998 ◽  
Vol 120 (1) ◽  
pp. 67-72 ◽  
Author(s):  
V. Kannan ◽  
J. B. Shung
Keyword(s):  
Finite Element ◽  
Iterative Procedure ◽  
Element Model ◽  
Design Parameters ◽  
Dimensional Model ◽  
Element Analysis ◽  
Analysis And Design ◽  
Type Machine ◽  
Free Body ◽  
The Finite Element Model

A two-dimensional model for a trochoidal-type machine without apex seals using finite element method has been developed with the help of Cosmos/M V1.65, and is evaluated by using a classical free-body technique. The minimum running clearance required to avoid contact between rotor and chamber is determined by an iterative procedure using the finite element model. The variation in the minimum required running clearance with the variation in the design parameters is studied. Guidelines for using the results of this study for an optimal design of a trochoidal-type machine without apex seals are presented.

scholarly journals Finite Element Analysis of Thermoelastic Instability With Intermittent Contact

1999 ◽  
Vol 122 (1) ◽  
pp. 42-46 ◽  
Author(s):  
Hubert J. M. Geijselaers ◽  
Annette J. E. Koning
Keyword(s):  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Dimensional Model ◽  
Governing Equations ◽  
Amplitude Function ◽  
Element Analysis ◽  
Thermoelastic Instability ◽  
Intermittent Contact ◽  
The Finite Element Model

The equations that describe the development of corrugations on block braked wheel treads caused by thermoelastic instability are discretized using the finite element method. The perturbations of temperatures and distortions are described by an amplitude function, which is spatially fixed multiplied by a sinusoidal running wave term of fixed wavelength. The governing equations are such that the wave term cancels out. Only the amplitude functions are discretized in the finite element model. The intermittent nature of the contact is directly specified through the boundary conditions. Results are obtained for a simplified two-dimensional model of a train wheel. These results agree with analytical results. [S0742-4787(00)00701-3]

A frequency response function-based updating technique for the finite element model of automotive structures

2008 ◽  
Vol 222 (10) ◽  
pp. 1781-1791 ◽  
Author(s):  
D-C Lee ◽  
C-S Han
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Design Parameters ◽  
External Loading ◽  
Element Analysis ◽  
Automotive Structures ◽  
Different Types ◽  
External Loads ◽  
The Finite Element Model ◽  
Huge Variety

Today's automotive industry uses finite element analysis (FEA) in a huge variety of applications in order to optimize structures and processes before hardware is produced. Efficiencies can be enhanced and margins are reduced because the external loads and structural properties are identified with higher confidence. The accuracy of FEA predictions has become increasingly important and directly influences the competitiveness of a product on the market. Because automotive structures are under dynamic environments, the correlation on the basis of static deformations independent of the mass and damping parameters do not provide a valuable reference from the view of the dynamic characteristics. In this paper, by systematically comparing the results from analytical and experimental analysis techniques, finite element (FE) models can be validated by the deterministic and robust design on the basis of each tolerance of design parameters, and improved so that they can be used with more confidence in further analysis. Making use of different types of test datum, a recommended procedure is to use a sequence of analysis in which mass, stiffness, damping, and external loading are validated and, if necessary, updated.

Redrawing Operation a Star Shape from Cylindrical Shape Using Experimental and FE Analysis

2020 ◽  
Vol 38 (1A) ◽  
pp. 25-32
Author(s):  
Waleed Kh. Jawad ◽  
Ali T. Ikal
Keyword(s):  
Finite Element ◽  
Effective Strain ◽  
Element Model ◽  
Cylindrical Shape ◽  
Element Analysis ◽  
Punch Force ◽  
Maximum Value ◽  
Element Simulation ◽  
Blank Sheet ◽  
The Finite Element Model

The aim of this paper is to design and fabricate a star die and a cylindrical die to produce a star shape by redrawing the cylindrical shape and comparing it to the conventional method of producing a star cup drawn from the circular blank sheet using experimental (EXP) and finite element simulation (FES). The redrawing and drawing process was done to produce a star cup with the dimension of (41.5 × 34.69mm), and (30 mm). The finite element model is performed via mechanical APDL ANSYS18.0 to modulate the redrawing and drawing operation. The results of finite element analysis were compared with the experimental results and it is found that the maximum punch force (39.12KN) recorded with the production of a star shape drawn from the circular blank sheet when comparing the punch force (32.33 KN) recorded when redrawing the cylindrical shape into a star shape. This is due to the exposure of the cup produced drawn from the blank to the highest tensile stress. The highest value of the effective stress (709MPa) and effective strain (0.751) recorded with the star shape drawn from a circular blank sheet. The maximum value of lamination (8.707%) is recorded at the cup curling (the concave area) with the first method compared to the maximum value of lamination (5.822%) recorded at the cup curling (the concave area) with the second method because of this exposure to the highest concentration of stresses. The best distribution of thickness, strains, and stresses when producing a star shape by

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

scholarly journals COMPARISON OF SAW BLADE NATURAL FREQUENCIES AND CRITICAL SPEEDS USING CSAW AND FINITE ELEMENT ANALYSIS

2011 ◽  
Author(s):  
J. Poirier ◽  
P. Radziszewski
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Natural Frequencies ◽  
Element Model ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Saw Blade ◽  
Circular Saws ◽  
The Finite Element Model ◽  
Element Method

The natural frequencies of circular saws limit the operating speeds of the saws. Current industry methods of increasing natural frequency include pretensioning, where plastic deformation is induced into the saw. To better model the saw, the finite element model is compared to current software for steel saws; C-SAW, a software program that calculates frequencies for stiffened circular saws. Using C-SAW and the finite element method the results are compared and the finite element method is validated for steel saws.

scholarly journals Finite element analysis of soft foundation treatment by thermal drainage consolidation of group well

2020 ◽  
Vol 198 ◽  
pp. 03025
Author(s):  
Kang Le ◽  
Zhang tingjun ◽  
Tong Junhui ◽  
Chen Di ◽  
Qian Baoyuan
Keyword(s):  
Finite Element ◽  
Model Test ◽  
New Technology ◽  
Element Model ◽  
Element Analysis ◽  
Mechanical Field ◽  
Foundation Treatment ◽  
Soft Foundation ◽  
Consolidation Effect ◽  
The Finite Element Model

Thermal drainage consolidation method is a new technology of soft foundation treatment, which involves the coupling of thermo-hydro-mechanical field, and the action mechanism is complex. In this paper, taking the model test of thermal drainage consolidation as the prototype, the finite element model of thermal drainage consolidation is established by using Abaqus software, then, the numerical results are obtained and are compared with the results of model test, and the reliability of the numerical model is verified. The results show that when the applied load is constant, the higher the temperature is, the faster the consolidation speed of soil is, but with the increase of temperature, the consolidation effect of the same temperature difference will gradually weaken. In addition, the thermal drainage consolidation method can achieve the best treatment effect when the temperature of the soil reaches 60 ℃.

Finite Element Analysis for the Crankshaft of the Piston Compressor

2010 ◽  
Vol 102-104 ◽  
pp. 17-21
Author(s):  
Bin Zhao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Piston Compressor ◽  
Element Model ◽  
Ansys Software ◽  
Element Analysis ◽  
Rotating Speed ◽  
Dynamical Characteristics ◽  
The Finite Element Model

In order to study the static and dynamical characteristics of the crankshaft, ANSYS software was used to carry out the corresponding calculations. The entity model of the crankshaft was established by UG software firstly, and then was imported into ANSYS software for meshing, and then the finite element model of the crankshaft was constructed. The crankshaft satisfied the requirement of stiffness and strength through static analysis. The top six natural frequencies and corresponding shapes were acquired through modal analysis, and the every order critical rotating speed of the crankshaft was calculated. The fatigue life of the crank was calculated by fatigue module of ANSYS software finally. These results offered the theoretical guidance for designing, manufacturing and repairing the crankshaft.

A Finite Element Analysis Study of Non-Linear Behavior in a Bolted Connection

1999 ◽  
Author(s):  
Richard B. Englund ◽  
David H. Johnson ◽  
Shannon K. Sweeney
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Sliding Friction ◽  
Element Model ◽  
Element Analysis ◽  
Bolted Connection ◽  
Fea Model ◽  
Linear Behavior ◽  
Radial Loading ◽  
The Finite Element Model

Abstract A finite element analysis (FEA) model of the interaction of a nut and bolt was used to investigate the effects of sliding, friction, and yielding in a bolted connection. The finite element model was developed as a two-dimensional, axisymmetric system, which allowed the study of axial and radial loading and displacements. This model did not permit evaluation of hoop or torsional effects such as tightening or the helical thread form. Results presented in this paper include the distribution of load between consecutive threads, the relative sliding along thread faces, and the stress distribution and regions of yielding in the model. Finally, a comparison to previous, linear analysis work and to published experimental data is made to conclude the paper.

Finite Element Analysis of Structural Strength of Concrete Mixing Truck’s Frame

2014 ◽  
Vol 945-949 ◽  
pp. 1143-1149
Author(s):  
Hai Xia Sun ◽  
Hua Kai Wei ◽  
Xiao Fang Zhao ◽  
Jia Rui Qi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Structural Strength ◽  
Element Model ◽  
Basic Element ◽  
Operating Conditions ◽  
Frame Structure ◽  
Element Analysis ◽  
The Finite Element Model

The finite element model of the concrete mixing truck’s frame is builded by using shell as basic element, and the process of building the finite element model of the balance suspension is introduced in detail. Based on this, frame’s stress on five types of typical operating conditions are calculated by using the finite element analysis software, NASTRAN, and results can show the dangerous position and the maximum stress position on the frame. The analysis result on structural strength can provide the basis for further improving the frame structure.

Sign in / Sign up

Export Citation Format

Share Document