Geometric Design of a Bio-Inspired Flapping Wing Mechanism Based on Bennett-Derived 6R Deployable Mechanisms

2014 ◽  
Author(s):  
Huang Hailin ◽  
Li Bing
Keyword(s):  
Flapping Wing ◽  
Geometric Design ◽  
Geometric Parameters ◽  
Degree Of Freedom ◽  
Single Degree Of Freedom ◽  
Flapping Motion ◽  
Single Degree ◽  
Revolute Joints ◽  
Air Vehicle ◽  
Deployable Mechanism

In this paper, we present the concept of designing flapping wing air vehicle by using the deployable mechanisms. A novel deployable 6R mechanism, with the deploying/folding motion of which similar to the flapping motion of the vehicle, is first designed by adding two revolute joints in the adjacent two links of the deployable Bennett linkage. The mobility of this mechanism is analyzed based on a coplanar 2-twist screw system. An intuitive projective approach for the geometric design of the 6R deployable mechanism is proposed by projecting the joint axes on the deployed plane. Then the geometric parameters of the deployable mechanism can be determined. By using another 4R deployable Bennett connector, the two 6R deployable wing mechanisms can be connected together such that the whole flapping wing mechanism has a single degree of freedom (DOF).

A New Family of Bricard-Derived Deployable Mechanisms

2016 ◽  
Vol 8 (3) ◽  
Author(s):  
Hailin Huang ◽  
Bing Li ◽  
Jianyang Zhu ◽  
Xiaozhi Qi
Keyword(s):  
Large Volume ◽  
Computer Aided Design ◽  
Degree Of Freedom ◽  
Single Degree Of Freedom ◽  
Single Degree ◽  
New Family ◽  
Revolute Joints ◽  
Computer Aided ◽  
Cad Models ◽  
Aided Design

This paper proposes a new family of single degree of freedom (DOF) deployable mechanisms derived from the threefold-symmetric deployable Bricard mechanism. The mobility and geometry of original threefold-symmetric deployable Bricard mechanism is first described, from the mobility characterstic of this mechanism, we show that three alternate revolute joints can be replaced by a class of single DOF deployable mechanisms without changing the single mobility characteristic of the resultant mechanisms, therefore leading to a new family of Bricard-derived deployable mechanisms. The computer-aided design (CAD) models are used to demonstrate these derived novel mechanisms. All these mechanisms can be used as the basic modules for constructing large volume deployable mechanisms.

Single-Degree-of-Freedom Rigidly Foldable Origami Flashers

2015 ◽  
Author(s):  
Robert J. Lang ◽  
Spencer Magleby ◽  
Larry Howell
Keyword(s):  
Degree Of Freedom ◽  
Deployable Structures ◽  
Single Degree Of Freedom ◽  
Single Degree ◽  
Revolute Joints

We present the design for a family of deployable structures based on the origami flasher that are rigidly foldable, i.e., foldable with revolute joints at the hinges and planar rigid faces, and that exhibit a single degree of freedom in their motion. These structures may be used to realize highly compact deployable mechanisms.

Graphical Methods to Locate the Secondary Instant Centers of Single-Degree-of-Freedom Indeterminate Linkages

2005 ◽  
Vol 127 (2) ◽  
pp. 249-256 ◽  
Author(s):  
David E. Foster ◽  
Gordon R. Pennock
Keyword(s):  
Degree Of Freedom ◽  
Graphical Methods ◽  
Single Degree Of Freedom ◽  
Revolute Joint ◽  
Single Degree ◽  
Revolute Joints ◽  
Straight Line ◽  
Single Link ◽  
Prismatic Joints ◽  
Two Degree Of Freedom

This paper presents graphical techniques to locate the unknown instantaneous centers of zero velocity of planar, single-degree-of-freedom, linkages with kinematic indeterminacy. The approach is to convert a single-degree-of-freedom indeterminate linkage into a two-degree-of-freedom linkage. Two methods are presented to perform this conversion. The first method is to remove a binary link and the second method is to replace a single link with a pair of links connected by a revolute joint. First, the paper shows that a secondary instant center of a two-degree-of-freedom linkage must lie on a unique straight line. Then this property is used to locate a secondary instant center of the single-degree-of-freedom indeterminate linkage at the intersection of two lines. The two lines are obtained from a purely graphical procedure. The graphical techniques presented in this paper are illustrated by three examples of single-degree-of-freedom linkages with kinematic indeterminacy. The examples are a ten-bar linkage with only revolute joints, the single flier eight-bar linkage, and a ten-bar linkage with revolute and prismatic joints.

Design of Cylindrical and Axisymmetric Origami Structures Based on Generalized Miura-Ori Cell

2019 ◽  
Vol 11 (5) ◽  
Author(s):  
Yucai Hu ◽  
Haiyi Liang ◽  
Huiling Duan
Keyword(s):  
Three Dimensional ◽  
Design Methods ◽  
Geometric Design ◽  
Degree Of Freedom ◽  
Single Degree Of Freedom ◽  
Single Degree ◽  
Flat Sheet ◽  
Folded Structure

Origami has shown its potential in designing a three-dimensional folded structure from a flat sheet of material. In this paper, we present geometric design methods to construct cylindrical and axisymmetric origami structures that can fit between two given surfaces. Due to the symmetry of the structures, a strip of folds based on the generalized Miura-ori cells is first constructed and then replicated longitudinally/circumferentially to form the cylindrical/axisymmetric origami structures. In both designs, algorithms are presented to ensure that all vertexes are either on or strictly within the region between the target surfaces. The conditions of flat-foldability and developability are fulfilled at the inner vertexes and the designs are rigid-foldable with a single degree-of-freedom. The methods for cylindrical and axisymmetric designs are similar in implementation and of potential in designing origami structures for engineering purposes, such as foldcores, foldable shelters, and metamaterials.

scholarly journals Design and analysis of single-degree-of-freedom flapping wing mechanism based on UG

2020 ◽  
Vol 1629 ◽  
pp. 012060
Author(s):  
Yafeng Zhang ◽  
Xiaobo Wang ◽  
Guoqiang Zhang ◽  
Jinhua Yang
Keyword(s):  
Flapping Wing ◽  
Degree Of Freedom ◽  
Single Degree Of Freedom ◽  
Single Degree

Single Degree-of-Freedom Rigidly Foldable Cut Origami Flashers

2016 ◽  
Vol 8 (3) ◽  
Author(s):  
Robert J. Lang ◽  
Spencer Magleby ◽  
Larry Howell
Keyword(s):  
Degree Of Freedom ◽  
Deployable Structures ◽  
Single Degree Of Freedom ◽  
Single Degree ◽  
Revolute Joints

We present the design for a family of deployable structures based on the origami flasher, which are rigidly foldable, i.e., foldable with revolute joints at the creases and planar rigid faces. By appropriate choice of sector angles and introduction of a cut, a single degree-of-freedom (DOF) mechanism is obtained. These structures may be used to realize highly compact deployable mechanisms.

Graphical Methods to Locate the Secondary Instant Centers of Single-Degree-of-Freedom Indeterminate Linkages

2004 ◽  
Author(s):  
David E. Foster ◽  
Gordon R. Pennock
Keyword(s):  
Degree Of Freedom ◽  
Graphical Methods ◽  
Single Degree Of Freedom ◽  
Single Degree ◽  
Revolute Joints ◽  
Straight Line ◽  
Single Link ◽  
Prismatic Joints ◽  
Instantaneous Center ◽  
Two Degree Of Freedom

This paper presents graphical techniques to locate the unknown instantaneous centers of zero velocity of planar, single-degree-of-freedom, linkages with kinematic indeterminacy. The approach is to convert a single-degree-of-freedom indeterminate linkage into a two-degree-of-freedom linkage. Two methods are presented to perform this conversion. The first method is to remove a binary link and the second method is to replace a single link with a pair of links connected by a revolute joint. First, the paper shows that a secondary instantaneous center of a two-degree-of-freedom linkage must lie on a unique straight line. Then this property is used to locate a secondary instant center of the single-degree-of-freedom linkage at the intersection of two lines. The two lines are obtained from a purely graphical procedure. The graphical techniques presented in this paper are illustrated by three examples of single-degree-of-freedom linkages with kinematic indeterminacy. The examples are a ten-bar linkage with only revolute joints, the single flier eight-bar linkage, and a ten-bar linkage with revolute and prismatic joints.

Motion Generation Using Combinations of Peaucellier Straight-Line Mechanisms

2012 ◽  
Author(s):  
Carl A. Nelson ◽  
Christian A. Padilla
Keyword(s):  
Rotation Angle ◽  
Geometric Parameters ◽  
Degree Of Freedom ◽  
Motion Generation ◽  
Single Degree Of Freedom ◽  
Complex Curve ◽  
Single Degree ◽  
Straight Line ◽  
Final Data ◽  
Trace Curves

The Peaucellier linkage is one of only a handful of known, single-degree-of-freedom mechanisms that trace an exact straight line. Although the traced output is straight, the relation between input rotation angle and output position along the traced line is nonlinear. The purpose of this study is to investigate the composite motion of stacked Peaucellier straight-line mechanisms. After stacking, the original straight-line output transforms into a complex curve whose shape is dependent on the motion of all of the component mechanisms, their geometric parameters, and how the component Peaucellier cells are interconnected. MATLAB software was used to generate output curves considering different stacking configurations and mechanism sizes. MATLAB was also used to analyze the final data and identify correlations between the mechanism link sizes, stacking configurations, and relative output curves. Based on a polynomial fitting technique, resultant output of the stacked mechanisms was generally found to be of 6th order except when purposefully constrained. This is a first attempt to characterize kinematic trace curves for this type of stacked straight-line linkage system.

Singularity Traces of Single Degree-of-Freedom Planar Linkages That Include Prismatic and Revolute Joints

2016 ◽  
Vol 8 (5) ◽  
Author(s):  
Saleh M. Almestiri ◽  
Andrew P. Murray ◽  
David H. Myszka ◽  
Charles W. Wampler
Keyword(s):  
Design Parameter ◽  
Closed Loop ◽  
Degree Of Freedom ◽  
Single Degree Of Freedom ◽  
Single Degree ◽  
Revolute Joints ◽  
Prismatic Joints ◽  
Motion Characteristics ◽  
Planar Linkages ◽  
General Method

This paper extends the general method to construct a singularity trace for single degree-of-freedom (DOF), closed-loop linkages to include prismatic along with revolute joints. The singularity trace has been introduced in the literature as a plot that reveals the gross motion characteristics of a linkage relative to a designated input joint and a design parameter. The motion characteristics identified on the plot include a number of possible geometric inversions (GIs), circuits, and singularities at any given value for the input link and the design parameter. An inverted slider–crank and an Assur IV/3 linkage are utilized to illustrate the adaptation of the general method to include prismatic joints.

Sign in / Sign up

Export Citation Format

Share Document