Effects of a Vane-Recessed Tubular-Passage Passive Stall Control Technique on a Multistage, Axial-Flow Compressor: Results of Tests on the First Stage With the Rear Stages Removed

2003 ◽  
Author(s):  
M. Akhlaghi ◽  
R. L. Elder ◽  
K. W. Ramsden
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Control Technique ◽  
Maximum Efficiency ◽  
Stall Margin ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Stall Margin Improvement ◽  
Blade Tip ◽  
Flow Compressor

The objective of the current study was to investigate the effect of casing treatment on a multistage axial flow compressor. The main purpose of the investigation was to extend the range and operability of multistage axial compressors. The study seeks to establish whether a vane-recessed tubular-passage casing-treatment could provide beneficial stall margin improvement, without sacrificing the efficiencies of the compressor with the restricted space available for the treatment. A casing treatment that consisted of three parts: an outer casing ring, with a tubular shaped passage on the inside, a set of 120 evenly spaced curved vanes, and then a shroud or inner ring was developed from two initial designs. The casing treatment, manufactured from high quality acrylic, was positioned upstream and partly covering the tip of the first stage rotor blades. The casing treatment was tested on the first stage of a three-stage low-speed compressor with inlet guide vanes with the rear two stages removed. The rotor blade tip axial chord exposure had a significant impact on the effectiveness of the casing treatment. Seven compressor configuration incorporating casing treatments of 23.2%, 33.3%, 43.4%, 53.5%, 63.6%, 73.7% and 83.8% rotor exposure were tested. The results showed significant improvements in stall margin in all exposures and insignificant efficiency sacrifices in some exposures. Nearly 29% of stall margin improvement in terms of the corrected mass flow rate was achieved with 33.3% rotor blade tip axial chord exposure. The compressor build with 53.5% rotor exposure was the best configuration in terms of maximum efficiency gain. In terms of peak pressure rise coefficients the compressor configuration with a casing treatment of 63.6% exposure was the best design. The results also suggest that the vane-recessed tubular-passage casing treatment designed as part of this research, in most instances enabled the stall conditions in the compressor to become progressive rather than abrupt.

Experimental and numerical investigation of a subsonic compressor with bend-skewed slot-casing treatment

2006 ◽  
Vol 220 (12) ◽  
pp. 1785-1796 ◽  
Author(s):  
X Lu ◽  
W Chu ◽  
Y Zhang ◽  
J Zhu
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Efficiency Gain ◽  
Stall Margin ◽  
Blade Passage ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor ◽  
Isentropic Efficiency

On the basis of the test results of discrete axial and blade angle slot casing treatment, a new type of casing treatment was designed for a subsonic axial flow compressor rotor by optimizing various geometry parameters. To obtain a wide operating range and to minimize penalties in terms of isentropic efficiency, seven compressor configurations incorporating casing treatments of 0, 16.6, 33.3, 50, 66.6, 83.3, and 100 per cent rotor exposures were experimentally investigated. The results showed that significant improvements in stall margin are possible in all exposures and insignificant isentropic efficiency sacrifices are recorded in some exposures. Nearly 21.43 per cent stall margin improvement in terms of the corrected mass flow-rate was achieved with 33.3 per cent rotor blade tip axial chord exposure. The compressor built with 16.6 per cent rotor exposure was the best configuration in terms of maximum isentropic efficiency gain. The second issue of the paper was to offer a contribution to the understanding of the physical mechanism by which bend-skewed slot-casing treatment improves stall margin under subsonic conditions. By applying a concept similar to ‘Domain scaling’ approach (as often used in multistage turbomachinery flow-fields) to the interface between the rotor blade passage and end-wall treatments, a time-dependent three-dimensional numerical simulation was performed for the subsonic axial-flow compressor rotor with bend-skewed slot-casing treatment. The numerical results agreed well with the available experimental results. Detailed analyses of the coupled flow through bend-skewed slot-casing treatment and rotor blade passage under subsonic conditions led to some preliminary conclusions as to the flow physics involved in the stall margin improvements afforded by the use of bend-skewed slot-casing treatment.

Experimental and Numerical Investigation of a Subsonic Compressor With Bend Skewed Slot Casing Treatment

2006 ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yanhui Wu
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Efficiency Gain ◽  
Stall Margin ◽  
Blade Passage ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor ◽  
Isentropic Efficiency

Based on the test results of discrete axial and blade angle slot casing treatment, a new type of casing treatment was designed for a subsonic axial flow compressor rotor by optimising various geometry parameters. To obtain a wide operating range and to minimize penalties in terms of isentropic efficiency, seven compressor configurations incorporating casing treatments of 0%, 16.6%, 33.3%, 50%, 66.6%, 83.3% and 100% rotor exposure were experimentally investigated. The results showed that significant improvements in stall margin are possible in all exposures and insignificant isentropic efficiency sacrifices are recorded in some exposures. Nearly 21.43% stall margin improvement in terms of the corrected mass flow rate was achieved with 33.3% rotor blade tip axial chord exposure. The compressor build with 16.6% rotor exposure was the best configuration in terms of maximum isentropic efficiency gain. The second issue of the paper was to offer a contribution to the understanding of the physical mechanism by which bend skewed slot casing treatment improve stall margin under subsonic conditions. By applying a concept similar to “Domain Scaling” approach (as often used in multistage turbomachinery Flow-fields) to the interface between the rotor blade passage and end-wall treatments, a time-dependent 3-dimentional numerical simulation was performed for the subsonic axial-flow compressor rotor with bend skewed slot casing treatment. The numerical results agreed well with experimental results. Detailed analyses of the coupled flow through bend skewed slot casing treatment and rotor blade passage under subsonic conditions led to some preliminary conclusions as to the flow physics involved in the stall margin improvements afforded by the use of bend skewed slot casing treatment.

scholarly journals Flow mechanism of affecting an axial flow compressor performance and stability with cross-blade slot casing treatments

2018 ◽  
Vol 233 (1) ◽  
pp. 17-36 ◽  
Author(s):  
HaoGuang Zhang ◽  
XuDong Zhang ◽  
YanHui Wu ◽  
WuLi Chu ◽  
HaiYang Kuang
Keyword(s):  
Axial Flow ◽  
Low Energy ◽  
Peak Efficiency ◽  
Stall Margin ◽  
Casing Treatment ◽  
Flow Loss ◽  
Stall Margin Improvement ◽  
And Performance ◽  
Flow Compressor ◽  
Casing Treatments

The objective of this study is to evaluate the effect of cross-blade slot casing treatment on the stability and performance of an axial flow compressor rotor. The experimental and unsteady calculated results both show that cross-blade slot casing treatment can generate about 22% stall margin improvement, and the compressor peak efficiency is reduced by about 13%. The detailed flow-field analyses indicate that the sucked and injected flow caused by the slots of cross-blade slot casing treatment can restrain the rotor tip passage blockage, which is made by the low energy tip clearance leakage vortex. When cross-blade slot casing treatment is applied, not only the rotor wheel flange work becomes lower in most of the rotor blade span, but also the flow loss in the blade tip passage becomes fairly large due to the strong interaction between the mainstream and the injected flows made by the slots. As a result, the compressor total pressure ratio and efficiency for cross-blade slot casing treatment are reduced obviously. Three kinds of new cross-blade slot casing treatment were designed according to the previous successful experience and investigated in this paper. The numerical results show that the new three cross-blade slot casing treatments both generate about 54% stall margin improvement at the cost of minor peak efficiency. For one new cross-blade slot casing treatment (CSCT2), the compressor peak efficiency is reduced by about 0.3%. The low energy TLV, which is present for cross-blade slot casing treatment, is removed by the strong sucked flow made by CSCT2. Moreover, the interaction between the mainstream and the injected flows caused by CSCT2 becomes weak obviously, and the corresponding flow loss is reduced greatly. Hence, the compressor stability and performance with CSCT2 are higher than those with cross-blade slot casing treatment.

Influence of Rain Ingestion on the Endwall Treatment in an Axial Flow Compressor

2018 ◽  
Vol 140 (8) ◽  
Author(s):  
Jichao Li ◽  
Juan Du ◽  
Mingzhen Li ◽  
Feng Lin ◽  
Hongwu Zhang ◽  
...  
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Pressure Rise ◽  
Water Film ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Water Ingestion ◽  
Blade Row ◽  
Flow Compressor ◽  
The Stability

The effects of water ingestion on the performance of an axial flow compressor are experimentally studied with and without endwall treatment. The background to the work is derived from the assessment of airworthiness for an aero-engine. The stability-enhancing effects with endwall treatments under rain ingestion are not previously known. Moreover, all the endwall treatments are designed under dry air conditions in the compressor. Water ingestion at 3% and 5% relative to the design mass flow proposed in the airworthiness standard are applied to initially investigate the effects on the performance under smooth casing (SC). Results show that the water ingestions are mainly located near the casing wall after they move through the rotor blade row. The pressure rise coefficient increases, efficiency declines, and torque increases under the proposed water ingestion. The increase of the inlet water increases the thickness of the water film downstream the rotor blade row and aggravates the adverse effects on the performances. Subsequently, three endwall treatments, namely circumferential grooves, axial slots, and hybrid slots–grooves, are tested with and without water ingestion. Compared with no water ingestion, the circumferential grooves basically have no resistance to the water ingestion. The axial slots best prevent the drop of the pressure rise coefficient induced by water ingestion, and hybrid slots–grooves are the second-best place owing to the contribution of the front axial slots. Therefore, the hybrid slots–grooves can not only extend the stall margin with less efficiency penalty compared with axial slots, but also prevent rain ingestion from worsening the compressor performance.

Flow Studies on a Single Stage Transonic Axial Flow Compressor Retrofitted With Circumferential Grooves and Varied Rotor-Stator Axial Gap

2017 ◽  
Author(s):  
Anand P. Darji ◽  
Dilipkumar Bhanudasji Alone ◽  
Chetan S. Mistry
Keyword(s):  
Numerical Study ◽  
Computational Study ◽  
Axial Flow ◽  
Single Stage ◽  
Experimental Results ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Stall Margin Improvement ◽  
Flow Compressor

A transonic axial flow compressor undergoes severe vibrations due to instabilities like stall and surge when it operates at lower mass flow rate in the absence of any control devices. In present study, the attempt was made to understand the combine impact of circumferential casing grooves (CCG) of constant aspect ratio and different axial spacing between rotor and stator on the operating stability of single stage transonic axial compressor and that of rotor alone using numerical simulation. The optimum rotor-stator gap in the presence of grooved casing treatment was identified. The steady state numerical analysis was performed by using three-dimensional Reynolds Average Navier-Stokes equation adapting shear stress transport (SST) k-ω turbulence model. The study is reported in two sections. First section includes the detailed numerical study on baseline case having smooth casing wall (SCW). The computational results were validated with the experimental results available at Propulsion Division of CSIR-NAL, Bangalore. The computational study shows good agreement with experimental results. The second section comprises the effects of optimum designs of CCG and various axial spacing on the stall margin improvement of transonic compressor. Current computational study shows that the axial spacing between rotor and stator is an important parameter for improvement in stall margin not only for SCW but also for CCG. Therefore, the highest stall margin improvement of 9% has achieved for 75% axial spacing.

Numerical Investigations of the Coupled Flow Through a Subsonic Compressor Rotor and Axial Skewed Slot

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yangfeng Zhang
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through ◽  
Flow Compressor

In order to advance the understanding of the fundamental mechanisms of axial skewed slot casing treatment and their effects on the subsonic axial-flow compressor flow field, the coupled unsteady flow through a subsonic compressor rotor and the axial skewed slot was simulated with a state-of-the-art multiblock flow solver. The computational results were first compared with available measured data, that showed the numerical procedure calculates the overall effect of the axial skewed slot correctly. Then, the numerically obtained flow fields were interrogated to identify the physical mechanism responsible for improvement in stall margin of a modern subsonic axial-flow compressor rotor due to the discrete skewed slots. It was found that the axial skewed slot casing treatment can increase the stall margin of subsonic compressor by repositioning of the tip clearance flow trajectory further toward the trailing of the blade passage and retarding the movement of the incoming∕tip clearance flow interface toward the rotor leading edge plane.

scholarly journals Recessed Casing Treatment Effects on Fan Performance and Flow Field

1995 ◽  
Author(s):  
C. S. Kang ◽  
A. B. McKenzie ◽  
R. L. Elder
Keyword(s):  
Flow Field ◽  
Axial Flow ◽  
Pressure Rise ◽  
Operating Efficiency ◽  
Flow Measurements ◽  
Blade Loading ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stall Margin Improvement ◽  
Blade Tip

An experimental investigation to examine the influence of the vaned recess casing treatment on stall margin, operating efficiency and the flow field of a low speed axial flow fan with aerospace type blade loading is presented. Different geometrical designs of the vaned passages were examined. The best configuration resulted in a stall margin improvement of 67%, a significantly higher pressure rise in the stall region and insignificant change in peak efficiency. Detailed 3-D flow measurements in the endwall region and in the casing recess were carried out with a slanted hot-wire, providing some insight to the operation of the device. The results revealed that the stall margin improvement was largely due to the removal of flow from the blade tip to the recess, and the elimination of the growth of the stall region at the tip, which occurs at stall in the solid casing build.

Mechanism investigation of enhancing the stability of an axial flow rotor by blade angle slots

2019 ◽  
Vol 233 (13) ◽  
pp. 4750-4764 ◽  
Author(s):  
Haoguang Zhang ◽  
Wenhao Liu ◽  
Enhao Wang ◽  
Yanhui Wu ◽  
Weidong Yao
Keyword(s):  
Axial Flow ◽  
Maximum Efficiency ◽  
Smooth Wall ◽  
Blade Angle ◽  
Stall Margin ◽  
Casing Treatment ◽  
Flow Losses ◽  
Stable Operating ◽  
Stall Margin Improvement ◽  
The Stability

This paper seeks to reveal the mechanisms of enhancing the stability of a subsonic axial flow rotor by applying blade angle slots casing treatment (BSCT). When blade angle slots are applied, there is about 9% stall margin improvement for the experiment and about 8% stall margin improvement for the calculation, but the decrease in the rotor maximum efficiency is about 11% for the experiment and the calculation. The compared results between smooth wall and blade angle slots indicate that the backflow in the rotor top passage is weakened by the injected and sucked flows formed inside the slots of BSCT. Moreover, the injected flows inside the slots interfere with the flows in the rotor passage upstream, and this interference leads to large flow losses. Therefore, the rotor efficiency for blade angle slots is much lower than that for smooth wall. To confirm that the structural optimization of blade angle slots can effectively improve the compressor stability with small efficiency losses, optimized blade angle slots casing treatment (BSCT1) was designed according to the past experience of slot casing treatment. The calculated result shows that the optimized blade angle slots generate about 59% stall margin improvement, and the compressor maximum efficiency with the optimized blade angle slots is about 0.05% more than that for smooth wall. The flow field analyses show that the strong sucked flows formed inside the slots for BSCT1 can prevent the backflow, which exists in the rotor top passage for BSCT, from appearing. In addition, the level of interference of the flows in the rotor passage upstream for BSCT1 is much lower than that for BSCT, and the corresponding losses with BSCT1 become lower. Therefore, the rotor with BSCT1 has a larger stable operating range and better efficiencies than that with BSCT.

Experimental study of self-recirculating casing treatment in a subsonic axial flow compressor

2016 ◽  
Vol 230 (8) ◽  
pp. 805-818 ◽  
Author(s):  
Wei Wang ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Yanhui Wu
Keyword(s):  
Axial Flow ◽  
Operating Conditions ◽  
Geometrical Parameters ◽  
Flow Angle ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Blade Tip ◽  
Overall Performance ◽  
Flow Compressor ◽  
Casing Treatments

Parametric studies of recirculating casing treatment were experimentally performed in a subsonic axial flow compressor. The recirculating casing treatment was parameterized with injector throat height, injection position, and circumferential coverage percentage. Eighteen recirculating casing treatments were tested to study the effects on compressor stability and on the compressor overall performance at three blade speeds. The profiles of recirculating casing treatment were optimized to minimize the losses generated by air recirculation. In the experiment, the stalling mass flow rate, total pressure ratio, and adiabatic efficiency of the compressor were measured to study the steady-state effects on the compressor performance of recirculating casing treatments, and static pressure disturbances on the casing wall were monitored to study the influence on stall dynamics. Results indicate that both the compressor stability and overall performance can be improved through recirculating casing treatment with appropriate geometrical parameters for all the test speeds. The influence on stall margin of one geometric parameter often depends on the choice of others, i.e. the interaction effects exist. In general, the recirculating casing treatment with a moderate injector throat and a large circumferential coverage is the optimal choice to enhance compressor stability. The injector of recirculating casing treatment should be placed upstream of the blade tip leading edge and the injector throat height should be lower than four times the rotor tip gap for the benefits of compressor efficiency. At 71% speed, the blade tip loading is decreased through recirculating casing treatment at the operating condition of near peak efficiency and increased near stall. Moreover, the outlet absolute flow angle is reduced in the tip region and enhanced at lower blade spans for both operating conditions. The stall inceptions are not changed with the implementation of recirculating casing treatment for all the test speeds, but the stall patterns are altered at 33% and 53% speeds, i.e. the stall with two cells is detected in the recirculating casing treatment compared with the solid casing with only one stall cell.

Numerically Understand the Combined Effect of Tip Clearance and Circumferential Grooves Casing Treatment on the Performance of Single Stage Transonic Axial Flow Compressor

2015 ◽  
Author(s):  
Mitesh Goswami ◽  
Dilipkumar Bhanudasji Alone ◽  
Harish S. Choksi
Keyword(s):  
Axial Flow ◽  
Single Stage ◽  
Tip Clearance ◽  
Combined Effect ◽  
Stall Margin ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Circumferential Groove ◽  
Flow Compressor ◽  
Stage Efficiency

This paper deals with the numerical studies on the combined effect of tip clearance and axisymmetric circumferential grooves casing treatment (CGCT) on the overall performance and stall margin of a single stage transonic axial flow compressor. Steady state numerical analysis was carried out by solving three dimensional Reynolds-averaged-Navier-Stokes (RANS) Equations using the Shear Stress Transport (SST) k-ω Turbulence Model. The numerical stall inception point was identified from the last converged point by the convergence criteria, and the stall margin was numerically predicted. Additionally, the stall margin and the isentropic peak stage efficiencies of the circumferential casing grooves with various tip clearances were compared and evaluated in order to explore the influence of the tip clearance. Results obtained were compared with those obtained on the baseline compressor with the smooth casing (SC). Further computational studies were conducted to study the role of the tip leakage flow in axial compressor in triggering the stall. The relationship between the tip clearance flow, flow field and surge margin extension from circumferential groove casing treatment with various rotor tip clearances were studied numerically. The application of the circumferential groove casing treatment with varying clearance leads to significant improvement in the operating stability of compressor with slight reduction in the isentropic peak stage efficiency for small tip clearances, whereas there was slight increment in the isentropic peak stage efficiency at higher tip clearance of 2.5 mm.

Sign in / Sign up

Export Citation Format

Share Document