Effect of Unsteady Wake on Film-Cooling Effectiveness Distribution on a Gas Turbine Blade With Compound Shaped Holes

2007 ◽  
Author(s):  
Diganta P. Narzary ◽  
Zhihong Gao ◽  
Shantanu Mhetras ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Suction Side ◽  
Intensity Level ◽  
Pressure Side ◽  
Wake Effect ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes

The effect of fan-shaped, laid-back compound angled cooling holes placed along the span of a fully-cooled high pressure turbine blade in a 5-blade linear cascade on film cooling effectiveness is studied using the Pressure Sensitive Paint (PSP) technique. Four rows of shaped film cooling holes are provided on the pressure side while two such rows are provided on the suction side of the blade. Three rows of cylindrical holes are drilled at 30° to the surface on the leading edge to capture the effect of showerhead film coolant injection. The coolant is injected at four different average blowing ratios of 0.3, 0.6, 0.9 and 1.2. Presence of wake due to upstream vanes is studied by placing a periodic set of rods upstream of the test blade. The wake is generated using 4.8mm diameter rods. The wake rods can be clocked by changing their stationary positions in front of the test blade to simulate a progressing wake. Effect of wake is recorded at four phase locations with equal intervals. The free stream Reynolds number, based on the axial chord length and the exit velocity, is 750,000 and the inlet and the exit Mach numbers are 0.27 and 0.44, respectively resulting in a blade pressure ratio of 1.14. Turbulence intensity level at the cascade inlet is 6% with an integral length scale of around 5cm. Results show that the fan-shaped, laid-back compound angled holes produce uniform and wide coolant coverage on the suction side except for those regions affected by the passage and tip leakage vortices. The advantage of compound shaped hole design is seen from the higher effectiveness values on the suction side compared to that of the compound cylindrical holes. The presence of a stationary upstream wake can result in lower film cooling effectiveness on the blade surface. Variation of blowing ratio from 0.3 to 1.2 show more or less uniform increment in effectiveness increase on the pressure side, whereas on the suction side, the increment shows signs of saturation beyond M = 0.6.

Film-Cooling on a Gas Turbine Blade Pressure Side or Suction Side With Compound Angle Shaped Holes

2007 ◽  
Author(s):  
Zhihong Gao ◽  
Diganta P. Narzary ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Suction Side ◽  
Steady Increase ◽  
Pressure Side ◽  
Wake Effect ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Compound Angle

The film cooling effectiveness on the surface of a high pressure turbine blade is measured using the Pressure Sensitive Paint (PSP). Four rows of fan-shaped, laid-back compound angled cooling holes are distributed on the pressure side while two such rows are provided on the suction side of the blade. The coolant is only injected to either the pressure side or suction side of the blade at five average blowing ratios from 0.4 to 1.5. Presence of wake due to upstream vanes is simulated by placing a periodic set of rods upstream of the test blade. The wake rods can be clocked by changing their stationary positions to simulate a progressing wake. Effect of wake is recorded at four phase locations with equal intervals along the pitch-wise direction. The free stream Reynolds number, based on the axial chord length and the exit velocity, is 750,000 and the inlet and the exit Mach numbers are 0.27 and 0.44, respectively, resulting in a blade pressure ratio of 1.14. Results reveal that the tip leakage vortices and endwall vortices sweep the coolant film on the suction side to the midspan region. The fan-shaped, laid-back compound angled holes produce good coolant film coverage on the suction side except for those regions affected by the secondary vortices. Due to the concave surface, the coolant trace is short and effectiveness level is low on the pressure surface. However, the pressure side acquires relatively uniform film coverage with the design of multiple rows of cooling holes. The presence of stationary upstream wake results in lower film cooling effectiveness on the blade surface. Variation of blowing ratio from 0.4 to 1.5 shows steady increase in effectiveness on the pressure side or the suction side for a given wake rod phases locations. The compound angle shaped holes outperform the compound angle cylindrical holes by the elevated film cooling effectiveness particularly at higher blowing ratios.

Film-Cooling on a Gas Turbine Blade Pressure Side or Suction Side With Compound Angle Shaped Holes

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Zhihong Gao ◽  
Diganta P. Narzary ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Suction Side ◽  
Pressure Side ◽  
Blade Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Compound Angle

The film-cooling effectiveness on the surface of a high pressure turbine blade is measured using the pressure sensitive paint technique. Compound angle laidback fan-shaped holes are used to cool the blade surface with four rows on the pressure side and two rows on the suction side. The coolant injects to one side of the blade, either pressure side or suction side. The presence of wake due to the upstream vanes is simulated by placing a periodic set of rods upstream of the test blade. The wake rods can be clocked by changing their stationary positions to simulate progressing wakes. The effect of wakes is recorded at four phase locations along the pitchwise direction. The freestream Reynolds number, based on the axial chord length and the exit velocity, is 750,000. The inlet and exit Mach numbers are 0.27 and 0.44, respectively, resulting in a pressure ratio of 1.14. Five average blowing ratios ranging from 0.4 to 1.5 are tested. Results reveal that the tip-leakage vortices and endwall vortices sweep the coolant on the suction side to the midspan region. The compound angle laidback fan-shaped holes produce a good film coverage on the suction side except for the regions affected by the secondary vortices. Due to the concave surface, the coolant trace is short and the effectiveness level is low on the pressure surface. However, the pressure side acquires a relatively uniform film coverage with the multiple rows of cooling holes. The film-cooling effectiveness increases with the increasing average blowing ratio for either side of coolant ejection. The presence of stationary upstream wake results in lower film-cooling effectiveness on the blade surface. The compound angle shaped holes outperform the compound angle cylindrical holes by the elevated film-cooling effectiveness, particularly at higher blowing ratios.

Effect of Superposition on Spanwise Film-Cooling Effectiveness Distribution on a Gas Turbine Blade

2006 ◽  
Author(s):  
Shantanu Mhetras ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Suction Side ◽  
Axial Direction ◽  
Intensity Level ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Full Coverage ◽  
Film Cooling Holes

The effect of film cooling holes placed along the span of high pressure turbine blade in a 5 bladed linear cascade on film cooling effectiveness is studied using the Pressure Sensitive Paint (PSP) technique. Four rows of film cooling holes are provided on the pressure side while two such rows are provided on the suction side of the blade. Around 22 cylindrical holes with a diameter of 0.65mm are drilled in each row at a compound angle of 45° to the blade span in the radial direction and at 45° in the axial direction. Film cooling effectiveness over the entire blade region is determined from full coverage film cooling with coolant blowing from all rows and from each individual row. The effect of superposition of film cooling effectiveness from each individual row is then compared with full coverage film cooling. The coolant is injected at four different average blowing ratios of 0.6, 0.9, 1.2 and 1.5. The free stream Reynolds number, based on the axial chord length and the exit velocity, is 750,000 and the inlet and the exit Mach numbers are 0.27 and 0.44, respectively resulting in a blade pressure ratio of 1.14. Turbulence intensity level at the cascade inlet is 6% with an integral length scale of around 5cm. Results show that the effectiveness magnitudes from superposition of effectiveness data from individual rows are comparable with that from full coverage film cooling. Varying blowing ratios can have a significant impact on film-cooling effectiveness distribution with a blowing ratio of 0.6 showing highest effectiveness immediately downstream of the holes.

The Experimental and Numerical Research for Linear Cascade Film Cooling With Different Hole Shapes

2010 ◽  
Author(s):  
Yi Lu ◽  
Yinyi Hong ◽  
Zhirong Lin ◽  
Xin Yuan
Keyword(s):  
Film Cooling ◽  
Large Scale ◽  
Leading Edge ◽  
Suction Side ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Linear Cascade ◽  
Blowing Ratio ◽  
Cylindrical Holes

Detailed film cooling effectiveness distributions were experimentally obtained on a turbine vane platform within a linear cascade. Testing was done in a large scale five-vane cascade with low freestream Renolds number condition 634,000 based on the axial chord length and the exit velocity. The detailed film-cooling effectiveness distributions on the platform were obtained using pressure sensitive paint technique. Two film-cooling hole configurations, cylindrical and fan-shaped, were used to cool the vane surface with two rows on pressure side, two rows on suction side and three rows on leading edge. For cylindrical holes, the blowing ratio of the coolant through the discrete cooling holes on pressure side and suction side ranged from 0.3 to 1.5 (based on the inlet mainstream velocity) while the blowing ratio ranging from 0.15 to 1.5 on leading edge; for fan-shaped holes, the four blowing ratios were 0.5, 1.0, 1.5 and 2.0. Results showed that average film-cooling effectiveness decreased with increasing blowing rate for the cylindrical holes, while the fan-shaped passage showed increased film-cooling effectiveness with increasing blowing ratio, indicating the fan-shaped cooling holes helped to improve film-cooling effectiveness by reducing overall jet liftoff. Fan-shaped holes improved average film-cooling effectiveness by 93.2%, 287.6% and 489.6% on pressure side, −4.1%, 27.9% and 78.2% on suction side over cylindrical holes at the blowing ratio of 0.5, 1.0 and 1.5 respectively. Numerical results were used to analyze the details of the flow and heat transfer on the cooling area with two turbulence models. Results demonstrated that tendency of the film cooling effectiveness distribution of numerical calculation and experimental measurement was generally consistent at different blowing ratio.

Influence of Coolant Density on Turbine Blade Film-Cooling Using Pressure Sensitive Paint Technique

2011 ◽  
Vol 134 (3) ◽  
Author(s):  
Diganta P. Narzary ◽  
Kuo-Chun Liu ◽  
Akhilesh P. Rallabandi ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Suction Side ◽  
Pressure Side ◽  
Pressure Sensitive Paint ◽  
Freestream Turbulence ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive

Adiabatic film-cooling effectiveness is examined on a high-pressure turbine blade by varying three critical engine parameters, viz., coolant blowing ratio, coolant-to-mainstream density ratio, and freestream turbulence intensity. Three average coolant blowing ratios (BR=1.2, 1.7, and 2.2 on the pressure side and BR=1.1, 1.4, and 1.8 on the suction side), three average coolant density ratios (DR=1.0, 1.5, and 2.5), and two average freestream turbulence intensities (Tu=4.2% and 10.5%) are considered. Conduction-free pressure sensitive paint (PSP) technique is adopted to measure film-cooling effectiveness. Three foreign gases—N2 for low density, CO2 for medium density, and a mixture of SF6 and argon for high density are selected to study the effect of coolant density. The test blade features two rows of cylindrical film-cooling holes on the suction side (45 deg compound), 4 rows on the pressure side (45 deg compound) and 3 around the leading edge (30 deg radial). The inlet and the exit Mach numbers are 0.24 and 0.44, respectively. The Reynolds number of the mainstream flow is 7.5×105 based on the exit velocity and blade chord length. Results suggest that the PSP is a powerful technique capable of producing clear and detailed film-effectiveness contours with diverse foreign gases. Large improvement on the pressure side and moderate improvement on the suction side effectiveness is witnessed when blowing ratio is raised from 1.2 to 1.7 and 1.1 to 1.4, respectively. No major improvement is seen thereafter with the downstream half of the suction side showing drop in effectiveness. The effect of increasing coolant density is to increase effectiveness everywhere on the pressure surface and suction surface except for the small region on the suction side, xss/Cx<0.2. Higher freestream turbulence causes effectiveness to drop everywhere except in the region downstream of the suction side where significant improvement in effectiveness is seen.

Effect of Flow Parameter Variations on Full Coverage Film-Cooling Effectiveness for a Gas Turbine Blade

2007 ◽  
Author(s):  
Shantanu Mhetras ◽  
Je-Chin Han ◽  
Ron Rudolph
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
Leading Edge ◽  
Suction Side ◽  
Intensity Level ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mach Numbers ◽  
Film Cooling Holes

The effect of film cooling holes placed along the span of a fully-cooled high pressure turbine blade in a stationary, linear cascade on film cooling effectiveness is studied using the Pressure Sensitive Paint (PSP) technique. Effect of showerhead injection at the leading edge and the presence of compound angled, diffusing holes on the pressure and suction side are also examined. Six rows of compound angled shaped film cooling holes are provided on the pressure side while four such rows are provided on the suction side of the blade. The holes have a laidback and fan-shaped diffusing cross-section. Another three rows of cylindrical holes are drilled at a typical angle on the leading edge to capture the effect of showerhead film coolant injection. The film cooling hole arrangement simulates a typical film cooled blade design used in stage 1 rotor blades for gas turbines used for power generation. A typical blowing ratio is defined for each film hole row and tests are performed for 100%, 150% and 200% of this typical value. Tests are performed for inlet Mach numbers of 0.36 and 0.45 with corresponding exit Mach numbers of 0.51 and 0.68 respectively. The flow remains subsonic in the throat region for both Mach numbers. The corresponding free stream Reynolds number, based on the axial chord length and the exit velocity, are 1.3 million and 1.74 million respectively. Freestream turbulence intensity level at the cascade inlet is 6%. Results show that varying blowing ratios can have a significant impact on film-cooling effectiveness distribution. Large spanwise variations in effectiveness distributions are also observed. Similar distributions were observed for both Mach numbers.

Numerical Predictions of Flow Structures and Film Cooling Effectiveness Values of a Turbine Vane: Effects of Secondary Holes

2019 ◽  
Author(s):  
Rui Zhu ◽  
Terrence W. Simon ◽  
Gongnan Xie
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Suction Side ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Cylindrical Holes ◽  
Better Than

Abstract In modern gas turbines, film cooling is the most common and efficient way to provide thermal protection for hot components. Secondary holes to a primary film cooling hole are used to improve film cooling performance by creating anti-kidney vortices, a technique that has been well documented using flat plate models. This study aims to evaluate the effects of secondary holes on film cooling effectiveness over an airfoil. The film cooling performance and flow fields of a row of primary holes with secondary holes on the pressure side and suction side of a C3X vane are numerically investigated and compared with the results of a single row of cylindrical holes and two rows of staggered cylindrical holes. Cases with different blowing ratios are analyzed. It is shown from the simulation that film cooling effectiveness of primary holes with secondary holes is much better than with a single row of cylindrical holes, and slightly better than with two rows of staggered holes on both pressure side and suction side, with the same amount of coolant usage and blowing ratio. The enhancement is higher on the pressure side than on the suction side. The results show that adding secondary holes can enhance film cooling effectiveness by creating anti-kidney vortices, which will weaken jet lift-off from the primary holes caused by the kidney vortex pair, especially at higher blowing ratios. In addition, film coverage of primary holes with secondary holes is wider and persists further downstream than for a single row of cylindrical holes.

Influence of Coolant Density on Turbine Blade Film-Cooling Using Pressure Sensitive Paint Technique

2010 ◽  
Author(s):  
Diganta P. Narzary ◽  
Kuo-Chun Liu ◽  
Akhilesh P. Rallabandi ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Suction Side ◽  
Pressure Side ◽  
Pressure Sensitive Paint ◽  
Freestream Turbulence ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive

Adiabatic film-cooling effectiveness is examined on a high pressure turbine blade by varying three critical engine parameters, viz., coolant blowing ratio, coolant-to-mainstream density ratio and freestream turbulence intensity. Three average coolant blowing ratios (BR = 1.2, 1.7, and 2.2 on the pressure side and BR = 1.1, 1.4, and 1.8 on the suction side), three average coolant density ratios (DR = 1.0, 1.5, and 2.5), and two average freestream turbulence intensities (Tu = 4.2% and 10.5%) are considered. Conduction-free Pressure Sensitive Paint (PSP) technique is adopted to measure film-cooling effectiveness. Three foreign gases— N2 for low density, CO2 for medium density, and a mixture of SF6 and Argon for high density are selected to study the effect of coolant density. The test blade features 2 rows of cylindrical film-cooling holes on the suction side (45° compound), 4 rows on the pressure side (45° compound) and 3 around the leading edge (30° radial). The inlet and the exit Mach numbers are 0.24 and 0.44, respectively. Reynolds number of the mainstream flow is 7.5E105 based on the exit velocity and blade chord length. Results suggest that the PSP is a powerful technique capable of producing clear and detailed film effectiveness contours with diverse foreign gases. Large improvement on the pressure side and moderate improvement on the suction side effectiveness is witnessed when blowing ratio is raised from 1.2 to 1.7 and 1.1 to 1.4, respectively. No major improvement is seen thereafter with the downstream half of the suction side showing drop in effectiveness. The effect of increasing coolant density is to increase effectiveness everywhere on the pressure surface and suction surface except for the small region on the suction side, xss/Cx&lt;0.2. Higher freestream turbulence causes effectiveness to drop everywhere except in the region downstream of the suction side where significant improvement in effectiveness is seen.

3D Flow Prediction and Improvement of Holes Arrangement of a Film-Cooled Turbine Blade Using a Feature-Based Jet Model

2006 ◽  
Author(s):  
Andre´ Burdet ◽  
Reza S. Abhari
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Good Prediction ◽  
Pressure Side ◽  
3D Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Numerical Predictions ◽  
Flow Prediction ◽  
Feature Based

A feature-based jet model has been proposed for use in 3D CFD prediction of turbine blade film cooling. The goal of the model is to be able to perform computationally efficient flow prediction and optimization of film-cooled turbine blades. The model reproduces in the near hole region the macro flow features of a coolant jet within a Reynolds-Averaged Navier Stokes (RANS) framework. Numerical predictions of the 3D flow through a linear transonic film-cooled turbine cascade are carried out with the model, with a low computational overhead. Different cooling holes arrangement are computed and the prediction accuracy is evaluated versus experimental data. It shown that the present model provides a reasonably good prediction of the adiabatic film-cooling effectiveness and Nusselt number around the blade. A numerical analysis of the interaction of coolant jets issuing from different rows of holes on the blade pressure side is carried out. It is shown that the upward radial migration of the flow due to the passage secondary flow structure has an impact on the spreading of the coolant and the film cooling effectiveness on the blade surface. Based on this result, a new arrangement of the cooling holes for the present case is proposed that leads to a better spanwise covering of the coolant on the blade pressure side surface.

Turbine Blade Platform Film Cooling With Simulated Swirl Purge Flow and Slashface Leakage Conditions

2016 ◽  
Author(s):  
Andrew F. Chen ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Leading Edge ◽  
Suction Side ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Purge Flow ◽  
Endwall Film Cooling ◽  
Film Cooling Holes

The combined effects of inlet purge flow and the slashface leakage flow on the film cooling effectiveness of a turbine blade platform were studied using the pressure sensitive paint (PSP) technique. Detailed film cooling effectiveness distributions on the endwall were obtained and analyzed. The inlet purge flow was generated by a row of equally-spaced cylindrical injection holes inside a single-tooth generic stator-rotor seal. In addition to the traditional 90 degree (radial outward) injection for the inlet purge flow, injection at a 45 degree angle was adopted to create a circumferential/azimuthal velocity component toward the suction side of the blades, which created a swirl ratio (SR) of 0.6. Discrete cylindrical film cooling holes were arranged to achieve an improved coverage on the endwall. Backward injection was attempted by placing backward injection holes near the pressure side leading edge portion. Slashface leakage flow was simulated by equally-spaced cylindrical injection holes inside a slot. Experiments were done in a five-blade linear cascade with an average turbulence intensity of 10.5%. The inlet and exit Mach numbers were 0.26 and 0.43, respectively. The inlet and exit mainstream Reynolds numbers based on the axial chord length of the blade were 475,000 and 720,000, respectively. The coolant-to-mainstream mass flow ratios (MFR) were varied from 0.5%, 0.75%, to 1% for the inlet purge flow. For the endwall film cooling holes and slashface leakage flow, blowing ratios (M) of 0.5, 1.0, and 1.5 were examined. Coolant-to-mainstream density ratios (DR) that range from 1.0 (close to low temperature experiments) to 1.5 (intermediate DR) and 2.0 (close to engine conditions) were also examined. The results provide the gas turbine engine designers a better insight into improved film cooling hole configurations as well as various parametric effects on endwall film cooling when the inlet (swirl) purge flow and slashface leakage flow were incorporated.

Sign in / Sign up

Export Citation Format

Share Document