Study of Unforced and Modulated Inclined Film-Cooling Jets Using Proper Orthogonal Decomposition: Part II—Forced Jets

2011 ◽  
Author(s):  
Guillaume Bidan ◽  
Clementine Vezier ◽  
Dimitris E. Nikitopoulos
Keyword(s):  
Flow Rate ◽  
Film Cooling ◽  
Cross Flow ◽  
Orthogonal Decomposition ◽  
Large Eddy Simulations ◽  
Time Resolved ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Large Eddy ◽  
Proper Orthogonal

The effects of jet flow-rate modulation were investigated in the case of a 35° inclined jet in cross-flow over a flat plate using Mie scattering visualizations, time-resolved flow rate records and large eddy simulations (LES). In forced experiments, average blowing ratios of 0.3 and 0.4 were investigated with a duty cycle of 50% and pulsing frequencies of St = 0.016 and 0.159. Time-resolved flow rate measurements during the experiments provided precise knowledge of the instantaneous jet blowing ratio and adequate inlet boundary conditions for large eddy simulations. The dynamics of the vortical structures generated during the transient parts of the forcing cycle as well as their impact on film cooling performance were investigated with respect of the forcing parameters. At the considered blowing ratios, a starting ring vortex was consistently generated at the transition from low to high blowing ratio. Ingestion of cross-flow fluid at the transition from high to low blowing ratio was also observed and had a negative impact on film cooling performance. All studied cases exhibited an overall decrease in coverage regardless of pulsing parameters over their corresponding steady jet cases at fixed mass flow rate. Comparisons between pulsed and steady jets at constant pressure supply (same high blowing ratio) did exhibit some film-cooling improvement with pulsing. 3D Proper orthogonal decomposition was performed on LES results at distinct forcing frequencies to provide an analysis of dominant modes in the velocity and temperature fields. Significantly different results were obtained depending on the forcing frequency.

Study of Unforced and Modulated Film-Cooling Jets Using Proper Orthogonal Decomposition—Part II: Forced Jets

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Guillaume Bidan ◽  
Clementine Vézier ◽  
Dimitris E. Nikitopoulos
Keyword(s):  
Flow Rate ◽  
Film Cooling ◽  
Cross Flow ◽  
Orthogonal Decomposition ◽  
Large Eddy Simulations ◽  
Time Resolved ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Large Eddy ◽  
Proper Orthogonal

The effects of jet flow-rate modulation were investigated in the case of a 35 deg inclined jet in cross-flow over a flat plate using Mie scattering visualizations, time-resolved flow rate records, and large eddy simulations (LES). In forced experiments, average blowing ratios of 0.3 and 0.4 were investigated with a duty cycle of 50% and pulsing frequencies of St = 0.016 and 0.159. Time-resolved flow rate measurements during the experiments provided precise knowledge of the instantaneous jet blowing ratio and adequate inlet boundary conditions for large eddy simulations. The dynamics of the vortical structures generated during the transient parts of the forcing cycle as well as their impact on film cooling performance were investigated with respect of the forcing parameters. At the considered blowing ratios, a starting ring vortex was consistently generated at the transition from low to high blowing ratio. Ingestion of cross-flow fluid at the transition from high to low blowing ratio was also observed and had a negative impact on film cooling performance. All studied cases exhibited an overall decrease in coverage regardless of pulsing parameters over their corresponding steady jet cases at fixed mass flow rate. Comparisons between pulsed and steady jets at constant pressure supply (same high blowing ratio) did exhibit some film-cooling improvement with pulsing. 3D Proper orthogonal decomposition was performed on LES results at distinct forcing frequencies to provide an analysis of dominant modes in the velocity and temperature fields. Significantly different results were obtained depending on the forcing frequency.

Study of Unforced and Modulated Film-Cooling Jets Using Proper Orthogonal Decomposition—Part I: Unforced Jets

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Guillaume Bidan ◽  
Clementine Vézier ◽  
Dimitris E. Nikitopoulos
Keyword(s):  
Proper Orthogonal Decomposition ◽  
Flow Rate ◽  
Film Cooling ◽  
Cross Flow ◽  
Mie Scattering ◽  
Orthogonal Decomposition ◽  
Temperature Fields ◽  
Cooling Performance ◽  
Wide Range ◽  
Proper Orthogonal

The effects of jet flow-rate modulation were investigated in the case of a 35 deg inclined jet in cross-flow over a flat plate using Mie scattering visualizations, time-resolved flow rate records, and large eddy simulations (LES). An unforced jet study was conducted over a wide range of blowing ratios to provide a baseline for comparison to the pulsed results. The two distinct and well known steady jet regimes (attached jet with high film cooling performance for BR < 0.4 and detached jet with poor film cooling performance for BR > 1.0) were related to the dynamics of characteristic vortical structures, significant in the transition from one regime to the other. Similarity of the inclined jet results with a past vertical jet study are also put in perspective when comparing wall adiabatic effectiveness results. 3D proper orthogonal decomposition (3D-POD) was performed on LES results of an unforced case at BR = 0.15 to provide an analysis of dominant modes in the velocity and temperature fields. Error calculations on the reconstructed fields provided an estimation of the number of modes necessary to obtain satisfactory reconstruction while revealing some of the shortcomings associated with POD.

Study of Unforced and Modulated Inclined Film-Cooling Jets Using Proper Orthogonal Decomposition: Part I—Unforced Jets

2011 ◽  
Author(s):  
Guillaume Bidan ◽  
Clementine Vezier ◽  
Dimitris E. Nikitopoulos
Keyword(s):  
Proper Orthogonal Decomposition ◽  
Flow Rate ◽  
Film Cooling ◽  
Cross Flow ◽  
Mie Scattering ◽  
Orthogonal Decomposition ◽  
Temperature Fields ◽  
Cooling Performance ◽  
Wide Range ◽  
Proper Orthogonal

The effects of jet flow-rate modulation were investigated in the case of a 35° inclined jet in cross-flow over a flat plate using Mie scattering visualizations, time-resolved flow rate records and large eddy simulations (LES). An unforced jet study was conducted over a wide range of blowing ratios to provide a baseline for comparison to the pulsed results. The two distinct and well known steady jet regimes (attached jet with high film cooling performance for BR<0.4 and detached jet with poor film cooling performance for BR>1.0) were related to the dynamics of characteristic vortical structures, significant in the transition from one regime to the other. Similarity of the inclined jet results with a past vertical jet study are also put in perspective when comparing wall adiabatic effectiveness results. 3D Proper Orthogonal Decomposition (3D-POD) was performed on LES results of an unforced case at BR = 0.15 to provide an analysis of dominant modes in the velocity and temperature fields. Error calculations on the reconstructed fields provided an estimation of the number of modes necessary to obtain satisfactory reconstruction while revealing some of the shortcomings associated with POD.

Large Eddy Simulations of Film-Cooling Flows With a Micro-Ramp Vortex Generator

2011 ◽  
Author(s):  
Aaron F. Shinn ◽  
S. Pratap Vanka
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Vortex Generator ◽  
Vortex Pair ◽  
Large Eddy Simulations ◽  
Wind Tunnel Experiments ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flows ◽  
Large Eddy

Large Eddy Simulations were performed to study the effect of a micro-ramp on an inclined turbulent jet interacting with a cross-flow in a film-cooling configuration. The micro-ramp vortex generator is placed downstream of the film-cooling jet. Changes in vortex structure and film-cooling effectiveness are evaluated and the genesis of the counter-rotating vortex pair in the jet is discussed. Results are reported with the jet modeled using a plenum/pipe configuration. This configuration was designed based on previous wind tunnel experiments at NASA Glenn Research Center, and the present results are meant to supplement those experiments. It is found that the micro-ramp improves film-cooling effectiveness by generating near-wall counter-rotating vortices which help entrain coolant from the jet and transport it to the surface. The pair of vortices generated by the micro-ramp are of opposite sense to the vortex pair embedded in the jet.

Computational analysis of span-wise hole locations on fluid flow and film cooling of internal channels with crescent ribs

2019 ◽  
Vol 29 (8) ◽  
pp. 2728-2753
Author(s):  
Guohua Zhang ◽  
Xueting Liu ◽  
Bengt Ake Sundén ◽  
Gongnan Xie
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Side Wall ◽  
Target Surface ◽  
Internal Cooling ◽  
Cooling Performance ◽  
Content Type ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cooling Air

Purpose This study aims to clarify the mechanism of film hole location at the span-wise direction of an internal cooling channel with crescent ribs on the adiabatic film cooling performance, three configurations are designed to observe the effects of the distance between the center of the ellipse and the side wall(Case 1, l = w/2, Case 2, l = w/3 and for Case 3, l = w/4). Design/methodology/approach Numerical simulations are conducted under two blowing ratios (i.e. 0.5 and 1) and a fixed cross-flow Reynolds number (Rec = 100,000) with a verified turbulence model. Findings It is shown that at low blowing ratio, reducing the distance increases the film cooling effectiveness but keeps the trend of the effectiveness unchanged, while at high blowing ratio, the characteristic is a little bit different in the range of 0 = x/D = 10. Research limitations/implications These features could be explained by the fact that shrinking the distance between the hole and side wall induces a much smaller reserved region and vortex downstream the ribs and a lower resistance for cooling air entering the film hole. Furthermore, the spiral flow inside the hole is impaired. Originality/value As a result, the kidney-shaped vortices originating from the jet flow are weakened, and the target surface can be well covered, resulting in an enhancement of the adiabatic film cooling performance.

Effect of Blowing Ratio in the Near-Stagnation Region of a Three-Row Leading Edge Film Cooling Geometry Using Large Eddy Simulations

2009 ◽  
Author(s):  
Sai Shrinivas Sreedharan ◽  
Danesh K. Tafti
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Large Eddy Simulations ◽  
Stagnation Region ◽  
Stagnation Line ◽  
Blowing Ratio ◽  
Large Eddy ◽  
Adiabatic Effectiveness ◽  
Compound Angle

Computational studies are carried out using Large Eddy Simulations (LES) to investigate the effect of coolant to mainstream blowing ratio in a leading edge region of a film cooled vane. The three row leading edge vane geometry is modeled as a symmetric semi-cylinder with a flat afterbody. One row of coolant holes is located along the stagnation line and the other two rows of coolant holes are located at ±21.3° from the stagnation line. The coolant is injected at 45° to the vane surface with 90° compound angle injection. The coolant to mainstream density ratio is set to unity and the freestream Reynolds number based on leading edge diameter is 32000. Blowing ratios (B.R.) of 0.5, 1.0, 1.5, and 2.0 are investigated. It is found that the stagnation cooling jets penetrate much further into the mainstream, both in the normal and lateral directions, than the off-stagnation jets for all blowing ratios. Jet dilution is characterized by turbulent diffusion and entrainment. The strength of both mechanisms increases with blowing ratio. The adiabatic effectiveness in the stagnation region initially increases with blowing ratio but then generally decreases as the blowing ratio increases further. Immediately downstream of off-stagnation injection, the adiabatic effectiveness is highest at B.R. = 0.5. However, further downstream the larger mass of coolant injected at higher blowing ratios, in spite of the larger jet penetration and dilution, increases the effectiveness with blowing ratio.

Experimental Investigation of Film Cooling Performance on Blade Endwall with Diffusion Slot Holes and Stator-Rotor Purge Flow

2021 ◽  
pp. 1-28
Author(s):  
Zhi-Qiang Yu ◽  
Jianjun Liu ◽  
Chen Li ◽  
Baitao An ◽  
Guang-Yao Xu
Keyword(s):  
Film Cooling ◽  
Flow Direction ◽  
Cross Flow ◽  
Orientation Angle ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Blowing Ratio ◽  
Shaped Hole

Abstract This paper focuses on the influences of the discrete hole shape and layout on the blade endwall film cooling effectiveness. The diffusion slot hole was first applied to the blade endwall and compared with the fan-shaped hole. The effect of upstream purge slot injection on the film cooling performance of the discrete hole was also investigated. Experiments were performed in a linear cascade with a exit Reynolds number of 2.64×105. The film cooling effectiveness on the blade endwall were measured by the pressure sensitive paint technique. Results indicate that the diffusion slot hole significantly increases the film cooling effectiveness on the blade endwall compared to the fan-shaped hole, especially at high blowing ratio. The maximum relative increment of the cooling effectiveness is over 40%. The layout with the discrete holes arranged lining up with the tangent direction of the blade profile offset curves exhibits a comparable film cooling effectiveness with the layout with the discrete holes arranged according to the cross-flow direction. The film cooling effectiveness on the pressure surface corner is remarkably enhanced by deflecting the hole orientation angle towards the pressure surface. The combination of purge slot and diffusion slot holes supplies a full coverage film cooling for the entire blade endwall at coolant mass flow ratio of the purge slot of 1.5% and blowing ratio of 2.5. In addition, the slot injection leads to a non-negligible influence on the cooling performance of the discrete holes near the separation line.

Flow Dynamics and Heat Transfer of a Stranded Overhead Conductor Cable

2020 ◽  
Author(s):  
Mohamed Abdelhady ◽  
David H. Wood
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Circular Cylinder ◽  
Coherent Structures ◽  
Carrying Capacity ◽  
Orthogonal Decomposition ◽  
Flow Dynamics ◽  
Large Eddy Simulations ◽  
Large Eddy ◽  
Proper Orthogonal

Abstract Stranded overhead conductor cables are used to transfer electric power, often over large distances. Conductor geometry, as well as environmental conditions, affect the power carrying capacity. This paper studies the flow dynamics and heat transfer for one stranded conductor geometry in air at Reynolds number of 1,000, determined using dynamic Smagorinsky Large Eddy Simulations. Proper Orthogonal Decomposition was used to identify coherent structures. In comparison to a smooth circular cylinder, the conductor strands noticeably affect the flow dynamics and heat transfer, locally and globally.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Cylindrical Holes

2017 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo ◽  
Ying-ni Zhai
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Cross Flow ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Flow Channels ◽  
Cylindrical Holes

This paper presents an experimental and numerical investigation on the film cooling with different coolant feeding channel structures. Two ribbed cross-flow channels with rib-orientation of 135° and 45° respectively and the plenum coolant channel have been studied and compared to find out the effect of rib orientation on the film cooling performances of cylindrical holes. The film cooling effectiveness and heat transfer coefficient were measured by the transient heat transfer measurement technique with narrow-band thermochromic liquid crystal. Numerical simulations with realizable k-ε turbulence model were also performed to analyze the flow mechanism. The results show that the coolant channel structure has a notable effect on the flow structure of film jet which is the most significant mechanism affecting the film cooling performance. Generally, film cooling cases fed with ribbed cross-flow channels have asymmetric counter-rotating vortex structures and related asymmetric temperature distributions, which make the film cooling effectiveness and the heat transfer coefficient distributions asymmetric to the hole centerline. The discharge coefficient of the 45° rib case is the lowest among the three cases under all the blowing ratios. And the plenum case has higher discharge coefficient than the 135° rib case under low blowing ratio. With the increase of blowing ratio, the discharge coefficient of the 135° rib case gets larger than the plenum case gradually, because the vortex in the upper half region of the coolant channel rotates in the same direction with the film hole inclination direction and makes the jet easy to flow into the film hole in the 135° rib case.

Sign in / Sign up

Export Citation Format

Share Document