CFD Simulations of Unsteady Wakes on a Highly Loaded Low Pressure Turbine Airfoil (L1A)

2012 ◽  
Author(s):  
Mounir B. Ibrahim ◽  
Samuel Vinci ◽  
Olga Kartuzova ◽  
Ralph J. Volino
Keyword(s):  
Computational Study ◽  
Separation Bubble ◽  
Low Pressure ◽  
Flow Coefficient ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
Cfd Simulations ◽  
Ansys Fluent ◽  
Low Pressure Turbine ◽  
Wake Passing

A study of a very high lift, low-pressure turbine airfoil in the presence of unsteady wakes was performed computationally and compared against experimental results. The experiments were conducted in a low speed wind tunnel under high (4.9%) and then low (0.6%) freestream turbulence intensity conditions with a flow coefficient (ζ) of 0.7. The experiments were done on a linear cascade with wakes that were produced from moving rods upstream of the cascade with the rod to blade spacing varied from 1 to 1.6 to 2. In the present study two different Reynolds numbers (25,000 and 50,000, based on the suction surface length and the nominal exit velocity from the cascade) were considered. The experimental and computational data have shown that in cases without wakes, the boundary layer separated and did not reattach. The CFD was performed with Large Eddy Simulation (LES) and Unsteady Reynolds-Averaged Navier-Stokes (URANS), Transition-SST, utilizing the finite-volume code ANSYS FLUENT under the same freestream turbulence and Reynolds number conditions as the experiment but only at a rod to blade spacing of 1. With wakes, separation was largely suppressed, particularly if the wake passing frequency was sufficiently high. Similar effect was predicted by 3D CFD simulations. Computational results for the pressure coefficients and velocity profiles were in a reasonable agreement with experimental ones for all cases examined. The 2D CFD efforts failed to capture the three dimensionality effects of the wake and thus were less consistent with the experimental data. As a further computational study, cases were run to simulate higher wake passing frequencies which were not run experimentally. The results of these computational cases showed that an initial 25% increase from the experimental dimensionless wake passing frequency of F = 0.45 greatly reduced the size of the separation bubble, nearly completely suppressing it, however an additional 33% increase on top of this did not prove to have much of an effect.

Synchronizing Separation Flow Control With Unsteady Wakes in a Low-Pressure Turbine Cascade

2007 ◽  
Author(s):  
M. Bloxham ◽  
D. Reimann ◽  
K. Crapo ◽  
J. Pluim ◽  
J. P. Bons
Keyword(s):  
Separation Zone ◽  
Separation Bubble ◽  
Vortex Generator ◽  
Low Pressure ◽  
Flow Coefficient ◽  
Separation Flow ◽  
Suction Surface ◽  
Piv Measurements ◽  
Low Pressure Turbine ◽  
Wake Passing

Particle image velocimetry (PIV) measurements were made on a highly loaded low-pressure turbine blade in a linear cascade. The Pack B blade has a design Zweifel coefficient of 1.15 and a peak Cp at 63% axial chord on the suction surface. Data were taken at Rec = 20K with 3% inlet freestream turbulence and a wake passing flow coefficient of 0.8. Without unsteady wakes, a non-reattaching separation bubble exists on the suction surface of the blade beginning at 68% axial chord. The time averaged separation zone is reduced in size by approximately 35% in the presence of unsteady wakes. Phase-locked hot-wire and PIV measurements were used to document the dynamics of this separation zone when subjected to synchronized, unsteady forcing from a spanwise row of vortex generator jets (VGJs) in addition to the unsteady wakes. The phase difference between VGJ actuation and the wake passing was optimized. Both steady state Cp and phase-locked velocity measurements confirm that the optimal combination of wakes and jets yields the smallest separation.

Synchronizing Separation Flow Control With Unsteady Wakes in a Low-Pressure Turbine Cascade

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
M. Bloxham ◽  
D. Reimann ◽  
K. Crapo ◽  
J. Pluim ◽  
J. P. Bons
Keyword(s):  
Separation Zone ◽  
Separation Bubble ◽  
Vortex Generator ◽  
Low Pressure ◽  
Flow Coefficient ◽  
Separation Flow ◽  
Suction Surface ◽  
Piv Measurements ◽  
Low Pressure Turbine ◽  
Wake Passing

Particle image velocimetry (PIV) measurements were made on a highly loaded low-pressure turbine blade in a linear cascade. The Pack B blade has a design Zweifel coefficient of 1.15 and a peak Cp at 63% axial chord on the suction surface. Data were taken at Rec=20K with 3% inlet freestream turbulence and a wake-passing flow coefficient of 0.8. Without unsteady wakes, a nonreattaching separation bubble exists on the suction surface of the blade beginning at 68% axial chord. The time-averaged separation zone is reduced in size by approximately 35% in the presence of unsteady wakes. Phase-locked hot-wire and PIV measurements were used to document the dynamics of this separation zone when subjected to synchronized, unsteady forcing from a spanwise row of vortex generator jets (VGJs) in addition to the unsteady wakes. The phase difference between VGJ actuation and the wake passing was optimized. Both steady state Cp and phase-locked velocity measurements confirm that the optimal combination of wakes and jets yields the smallest separation.

Effect of Unsteady Wakes on Boundary Layer Separation on a Very High Lift Low Pressure Turbine Airfoil

2010 ◽  
Author(s):  
Ralph J. Volino
Keyword(s):  
Boundary Layer ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
High Lift ◽  
Layer Separation ◽  
Low Pressure Turbine ◽  
Wake Passing ◽  
Very High

Boundary layer separation has been studied on a very high lift, low-pressure turbine airfoil in the presence of unsteady wakes. Experiments were done under low (0.6%) and high (4%) freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Wakes were produced from moving rods upstream of the cascade. Flow coefficients were varied from 0.35 to 1.4 and wake spacing was varied from 1 to 2 blade spacings, resulting in dimensionless wake passing frequencies F = fLj-te/Uave (f is the frequency, Lj-te is the length of the adverse pressure gradient region on the suction surface of the airfoils, and Uave is the average freestream velocity) ranging from 0.14 to 0.56. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Instantaneous velocity profile measurements were acquired in the suction surface boundary layer and downstream of the cascade. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) of 25,000 and 50,000. In cases without wakes, the boundary layer separated and did not reattach. With wakes, separation was largely suppressed, particularly if the wake passing frequency was sufficiently high. At lower frequencies the boundary layer separated between wakes. Background freestream turbulence had some effect on separation, but its role was secondary to the wake effect.

Effect of Unsteady Wakes on Boundary Layer Separation on a Very High Lift Low Pressure Turbine Airfoil

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
Ralph J. Volino
Keyword(s):  
Boundary Layer ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
High Lift ◽  
Layer Separation ◽  
Low Pressure Turbine ◽  
Wake Passing ◽  
Very High

Boundary layer separation has been studied on a very high lift, low pressure turbine airfoil in the presence of unsteady wakes. Experiments were done under low (0.6%) and high (4%) freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Wakes were produced from moving rods upstream of the cascade. Flow coefficients were varied from 0.35 to 1.4 and wake spacing was varied from one to two blade spacings, resulting in dimensionless wake passing frequencies F=fLj-te/Uave (f is the frequency, Lj-te is the length of the adverse pressure gradient region on the suction surface of the airfoils, and Uave is the average freestream velocity) ranging from 0.14 to 0.56. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Instantaneous velocity profile measurements were acquired in the suction surface boundary layer and downstream of the cascade. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) of 25,000 and 50,000. In cases without wakes, the boundary layer separated and did not reattach. With wakes, separation was largely suppressed, particularly if the wake passing frequency was sufficiently high. At lower frequencies the boundary layer separated between wakes. Background freestream turbulence had some effect on separation, but its role was secondary to the wake effect.

scholarly journals Detailed Studies on Separated Boundary Layers Over Low-Pressure Turbine Airfoils Under Several High Lift Conditions: Effect of Freesteam Turbulence

2009 ◽  
Author(s):  
Ken-ichi Funazaki ◽  
Kazutoyo Yamada ◽  
Nozomi Tanaka ◽  
Yasuhiro Chiba
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Separation Bubble ◽  
Low Pressure ◽  
Scale Model ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Turbine Airfoils

This paper deals with experimental investigation on the interaction between inlet freestream turbulence and boundary layers with separation bubble on a low-pressure turbine airfoil under several High Lift conditions. Solidity of the cascade can be reduced by increasing the airfoil pitch by 25%, while maintaining the throat in the blade-to-blade passage. Reynolds number examined is 57000, based on chord length and averaged exit velocity. Freestream turbulence intensity at the inlet is varied from 0.80% (no grid condition) to 2.1% by use of turbulence grid. Hot-wire probe measurements of the boundary layer on the suction surface for Low Pressure (LP) turbines rotor are carried out to obtain time-averaged and time-resolved characteristics of the boundary layers under the influence of the freestream turbulence. Frequency analysis extracts some important features of the unsteady behaviors of the boundary layer, including vortex formation and shedding. Numerical analysis based on high resolution Large Eddy Simulation is also executed to enhance the understanding on the flow field around the highly loaded turbine airfoils. Standard Smagorinsky model is employed as subgrid scale model. Emphasis of the simulation is placed on the relationship of inherent instability of the shear layer of the separation bubble and the freestream turbulence.

An Experimental Investigation of the Effect of Freestream Turbulence on the Wake of a Separated Low-Pressure Turbine Blade at Low Reynolds Numbers

1999 ◽  
Vol 122 (2) ◽  
pp. 431-433 ◽  
Author(s):  
C. G. Murawski ◽  
K. Vafai
Keyword(s):  
Reynolds Number ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Low Pressure Turbine ◽  
Flow Reynolds Number

An experimental study was conducted in a two-dimensional linear cascade, focusing on the suction surface of a low pressure turbine blade. Flow Reynolds numbers, based on exit velocity and suction length, have been varied from 50,000 to 300,000. The freestream turbulence intensity was varied from 1.1 to 8.1 percent. Separation was observed at all test Reynolds numbers. Increasing the flow Reynolds number, without changing freestream turbulence, resulted in a rearward movement of the onset of separation and shrinkage of the separation zone. Increasing the freestream turbulence intensity, without changing Reynolds number, resulted in shrinkage of the separation region on the suction surface. The influences on the blade’s wake from altering freestream turbulence and Reynolds number are also documented. It is shown that width of the wake and velocity defect rise with a decrease in either turbulence level or chord Reynolds number. [S0098-2202(00)00202-9]

The Effect of Wake Passing on a Flow Separation in a Low-Pressure Turbine Cascade

2004 ◽  
Vol 126 (2) ◽  
pp. 250-256 ◽  
Author(s):  
Michael J. Brear ◽  
Howard P. Hodson
Keyword(s):  
Separation Bubble ◽  
Phase Locking ◽  
Experimental Studies ◽  
Leading Edge ◽  
Low Pressure ◽  
Pressure Surface ◽  
Low Pressure Turbine ◽  
Numerical Predictions ◽  
Unsteady Interaction ◽  
Wake Passing

This paper describes an investigation into the effect that passing wakes have on a separation bubble that exists on the pressure surface and near the leading edge of a low-pressure turbine blade. Previous experimental studies have shown that the behavior of this separation is strongly incidence dependent and that it responds to its disturbance environment. The results presented in this paper examine the effect of wake passing in greater detail. Two-dimensional, Reynolds averaged, numerical predictions are first used to examine qualitatively the unsteady interaction between the wakes and the separation bubble. The separation is predicted to consist of spanwise vortices whose development is in phase with the wake passing. However, comparison with experiments shows that the numerical predictions exaggerate the coherence of these vortices and also overpredict the time-averaged length of the separation. Nonetheless, experiments strongly suggest that the predicted phase locking of the vortices in the separation onto the wake passing is physical.

Separated Flow Measurements on a Highly Loaded Low-Pressure Turbine Airfoil

2008 ◽  
Author(s):  
Ralph J. Volino
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Separation Bubble ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Transition To Turbulence ◽  
Suction Surface ◽  
Airfoil Surface ◽  
Flow Measurements ◽  
Low Pressure Turbine

Boundary layer separation, transition and reattachment have been studied on a new, very high lift, low-pressure turbine airfoil. Experiments were done under low freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Velocity profiles were acquired in the suction side boundary layer at several streamwise locations using hot-wire anemometry. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) ranging from 25,000 to 330,000. In all cases the boundary layer separated, but at high Reynolds number the separation bubble remained very thin and quickly reattached after transition to turbulence. In the low Reynolds number cases, the boundary layer separated and did not reattach, even when transition occurred. This behavior contrasts with previous research on other airfoils, in which transition, if it occurred, always induced reattachment, regardless of Reynolds number.

The Effect of Wake Passing on a Flow Separation in a Low Pressure Turbine Cascade

2003 ◽  
Author(s):  
Michael J. Brear ◽  
Howard P. Hodson
Keyword(s):  
Separation Bubble ◽  
Phase Locking ◽  
Experimental Studies ◽  
Leading Edge ◽  
Low Pressure ◽  
Pressure Surface ◽  
Low Pressure Turbine ◽  
Numerical Predictions ◽  
Unsteady Interaction ◽  
Wake Passing

This paper describes an investigation into the effect that passing wakes have on a separation bubble that exists on the pressure surface and near the leading edge of a low pressure turbine blade. Previous experimental studies have shown that the behaviour of this separation is strongly incidence dependent and that it responds to its disturbance environment. The results presented in this paper examine the effect of wake passing in greater detail. Two dimensional, Reynolds averaged, numerical predictions are first used to examine qualitatively the unsteady interaction between the wakes and the separation bubble. The separation is predicted to consist of spanwise vortices whose development is in phase with the wake passing. However, comparison with experiments shows that the numerical predictions exaggerate the coherence of these vortices and also overpredict the time-averaged length of the separation. Nonetheless, experiments strongly suggest that the predicted phase locking of the vortices in the separation onto the wake passing is physical.

Generation and Development of Klebanoff Streaks in Low-Pressure Turbine Cascade Under Upstream Wakes

2020 ◽  
Author(s):  
Shuang Sun ◽  
Xingshuang Wu ◽  
Tianrong Tan ◽  
Canlin Zuo ◽  
Sirui Pan ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Wall Shear Stress ◽  
Separation Bubble ◽  
Transition Process ◽  
Low Pressure ◽  
Suction Surface ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Wall Shear

Abstract At low Reynolds numbers operating condition, the boundary layer of the high-lift low-pressure turbine (LPT) of aero-engines is prone to separate on the suction surface of the airfoil. The profile losses of the airfoil are largely governed by the size of the separation bubble and the transition process in the boundary layer. However, the wake-induced transition, the natural transition and the instability induced by the Klebanoff streaks complicate the transition process. The boundary layer on the suction surface of a high-lift LPT was investigated at Re = 50,000 with upstream wakes. The numerical simulation was performed with the CFX software using large eddy simulations (LES), and the experiment was performed on a linear cascade. In this study, the wake is divided into the wake center and the wake tail, the unsteady formation process of the streaks and the wall shear stress caused by the wake are analyzed. A new mechanism of generation and development of Klebanoff Streaks was presented to better understand the effect of the wake on the boundary layer. Moreover, it was found that after entering the blade passage, the wake center does not contact the blade but causes the wall shear stress of the front part on the suction surface to increase. However, it is not possible to form strong Klebanoff streaks at the leading edge of the blade by shear sheltering effect. Only the wake tail can form Klebanoff streaks when it contacts the blade.

Sign in / Sign up

Export Citation Format

Share Document