Laminar Entropy Generation Over a Flat Plate With Isothermal and Constant Heat Flux Boundary Conditions Using the Von Ka´rma´n Integral Method

Volume 1 ◽  
2004 ◽  
Author(s):  
Eric B. Ratts ◽  
J. Steven Brown
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boundary Conditions ◽  
Flat Plate ◽  
Entropy Generation ◽  
Single Phase ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Fundamental Study ◽  
Flux Boundary Conditions

This paper is a fundamental study on the irreversibility of single-phase laminar convective heat transfer over a flat plate with isothermal and constant heat flux boundary conditions. It quantifies the losses due to viscous momentum transfer losses and heat transfer losses and presents the irreversibility of the convective flow based on the entropy generation (EG) method. This paper determines the entropy generation for incompressible, single phase, laminar flow for large and small Prandtl numbers over a flat plate with isothermal and constant heat flux boundary conditions using von Ka´rma´n’s integral theory.

On Effects of Temperature Boundary Conditions on Heat Transfer in Turbulent Low-Prandtl-Number Flows

2020 ◽  
Author(s):  
Ivan Otic
Keyword(s):  
Heat Transfer ◽  
Boundary Condition ◽  
Heat Flux ◽  
Boundary Conditions ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Flux Boundary Condition ◽  
Large Eddy ◽  
Heat Flux Boundary Condition ◽  
Effects Of Temperature

Abstract One important issue in understanding and modeling of turbulent heat transfer is the behavior of fluctuating temperature close to the wall. Common engineering computational approach assumes constant heat flux boundary condition on heated walls. In the present paper constant heat flux boundary condition was assumed and effects of temperature fluctuations are investigated using large eddy simulations (LES) approach. A series of large eddy simulations for two geometries is performed: First, forced convection in channels and second, forced convection over a backward facing step. LES simulation data is statistically analyzed and compared with results of direct numerical simulations (DNS) from the literature which apply three cases of heat flux boundary conditions: 1. ideal heat flux boundary condition, 2. non-ideal heat flux boundary condition, 3. conjugate heat transfer boundary condition. For low Prandtl number flows LES results show that, despite very good agreement for velocities and mean temperature, predictions of temperature fluctuations may have strong deficiencies if simplified boundary conditions are applied.

Entropy Generation Minimization of Fully Developed Internal Convective Flows With Constant Heat Flux

2003 ◽  
Author(s):  
Eric B. Ratts ◽  
Atul G. Raut
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Laminar Flow ◽  
Turbulent Flow ◽  
Entropy Generation ◽  
Cross Sections ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Entropy Generation Minimization

This paper addresses the thermodynamic optimum of single-phase convective heat transfer in fully developed flow for uniform and constant heat flux. The optimal Reynolds number is obtained using the entropy generation minimization (EGM) method. Entropy generation due to viscous dissipation and heat transfer dissipation in the flow passage are summed, and then minimized with respect to Reynolds number based on hydraulic diameter. For fixed mass flow rate and fixed total heat transfer rate, and the assumption of uniform heat flux, an optimal Reynolds number for laminar as well as turbulent flow is obtained. In addition, the method quantifies the flow irreversibilities. It was shown that the ratio of heat transfer dissipation to viscous dissipation at minimum entropy generation was 5:1 for laminar flow and 29:9 for turbulent flow. For laminar flow, the study compared non-circular cross-sections to the circular cross-section. The optimal Reynolds number was determined for the following cross-sections: square, equilateral triangle, and rectangle with aspect ratios of two and eight. It was shown that the rectangle with the higher aspect ratio had the smallest optimal Reynolds number, the smallest entropy generation number, and the smallest flow length.

Effects of Nanoparticle Migration on Water/Alumina Nanofluid Flow Inside a Horizontal Annulus with a Moving Core

2014 ◽  
Vol 31 (3) ◽  
pp. 291-305 ◽  
Author(s):  
A. Malvandi ◽  
D. D. Ganji
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boundary Conditions ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Outer Wall ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Thermal Boundary Conditions ◽  
Alumina Nanofluid

AbstractThe present study is a theoretical investigation of the laminar flow and convective heat transfer of water/alumina nanofluid inside a horizontal annulus with a streamwise moving inner cylinder. A modified, two-component, four-equation, nonhomogeneous equilibrium model is employed for the alumina/water nanofluid, which fully accounts for the effect of the nanoparticle volume fraction distribution. To determine the effects of thermal boundary conditions on the migration of the nanoparticles, two cases are considered: constant heat flux at the outer wall with an adiabatic inner wall (Case A) and constant heat flux at the inner wall with an adiabatic outer wall (Case B). The numerical results indicate that the thermal boundary conditions at the pipe walls significantly affect the nanoparticle distribution, particularly in cases where the ratio of Brownian motion to thermophoretic diffusivities is small. Moreover, increasing the velocity of the moving inner cylinder reduces the heat transfer rate for Case A. Conversely, in Case B, the movement of the inner cylinder enhances the heat transfer rate, and anomalous heat transfer enhancement occurs when the thermophoretic force is dominant (in larger nanoparticles).

Sign in / Sign up

Export Citation Format

Share Document