Combustion Noise Investigation With Multi-Cylinder RCCI

2013 ◽  
Author(s):  
Scott J. Curran ◽  
James P. Szybist ◽  
Robert M. Wagner
Keyword(s):  
Pressure Rise ◽  
Combustion Noise ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Engine Operation ◽  
Reactivity Controlled Compression Ignition ◽  
Pressure Rise Rate ◽  
Advanced Combustion ◽  
Rise Rate ◽  
Noise Metrics

Advanced combustion techniques have shown promise for achieving high thermal efficiency with simultaneous reductions in oxides of nitrogen (NOx) and particulate matter (PM) emissions. Many advanced combustion studies have used some form of noise-related metric to constrain engine operation, whether it be cylinder pressure rise rate, combustion noise, or ringing intensity. As the development of advanced combustion techniques progresses towards production-viable concepts, combustion noise is anticipated to be of the upmost concern for consumer acceptability. This study compares the noise metrics of cylinder pressure rise rate with combustion noise as measured by an AVL combustion noise meter over a wide range of engine operation conditions with reactivity controlled compression ignition on a light-duty multi-cylinder diesel engine modified to allow for direct injection of diesel fuel and port fuel injection of gasoline. Key parameters affecting noise metrics are engine load, speed, and the amount of boost. The trade-offs between high efficiency, low NOX emissions, and combustion noise were also explored. Additionally, the combustion noise algorithm integrated into the Drivven combustion analysis toolkit is compared to cylinder pressure rise rate and combustion noise as measured with a combustion noise meter. It is shown that the combustion noise of the multi-cylinder reactivity controlled compression ignition map can approach 100 dB while keeping the maximum pressure rise under 100 kPa/CAD.

Drive Cycle Efficiency and Emissions Estimates for Reactivity Controlled Compression Ignition in a Multi-Cylinder Light-Duty Diesel Engine

2011 ◽  
Author(s):  
Scott J. Curran ◽  
Kukwon Cho ◽  
Thomas E. Briggs ◽  
Robert M. Wagner
Keyword(s):  
Diesel Engine ◽  
Pressure Rise ◽  
Injection System ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Drive Cycle ◽  
Reactivity Controlled Compression Ignition ◽  
Pressure Rise Rate ◽  
Light Duty ◽  
Rise Rate

In-cylinder blending of gasoline and diesel to achieve Reactivity Controlled Compression Ignition (RCCI) has been shown to reduce NOx and PM emissions while maintaining or improving brake thermal efficiency (BTE) as compared to conventional diesel combustion (CDC). The RCCI concept has an advantage over many advanced combustion strategies in that by varying both the percent of premixed gasoline and EGR rate, stable combustion can be extended over more of the light-duty drive cycle load range. Changing the percent of premixed gasoline changes the fuel reactivity stratification in the cylinder providing further control of combustion phasing and cylinder pressure rise rate than the use of EGR alone. This paper examines the combustion and emissions performance of light-duty diesel engine using direct injected diesel fuel and port injected gasoline to enable RCCI for steady-state engine conditions which are consistent with a light-duty drive cycle. A GM 1.9L four-cylinder engine with the stock compression ratio of 17.5:1, common rail diesel injection system, high-pressure EGR system and variable geometry turbocharger was modified to allow for port fuel injection with gasoline. Engine-out emissions, engine performance and combustion behavior for RCCI operation is compared against both CDC and a premixed charge compression ignition (PCCI) strategy which relies on high levels of EGR dilution. The effect of percent of premixed gasoline, EGR rate, boost level, intake mixture temperature, combustion phasing, and cylinder pressure rise rate is investigated for RCCI combustion for the light-duty modal points. Engine-out emissions of NOx and PM were found to be considerably lower for RCCI operation as compared to CDC and PCCI, while HC and CO emissions were higher. BTE was similar or higher for many of the modal conditions for RCCI operation. The emissions results are used to estimate hot-start FTP-75 emissions levels with RCCI and are compared against CDC and PCCI modes.

Post Injection Strategy for the Reduction of the Peak Pressure Rise Rate of Neat N-Butanol Combustion

2015 ◽  
Author(s):  
Marko Jeftić ◽  
Ming Zheng
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
Injection Timing ◽  
Post Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Injection Duration ◽  
Rise Rate

Enhanced premixed combustion of neat butanol in a compression ignition engine can have challenges with regards to the peak pressure rise rate and the peak in-cylinder pressure. It was proposed to utilize a butanol post injection to reduce the peak pressure rise rate and the peak in-cylinder pressure while maintaining a constant engine load. Post injection timing and duration sweeps were carried out with neat n-butanol in a compression ignition engine. The post injection timing sweep results indicated that the use of an early butanol post injection reduced the peak pressure rise rate and the peak in-cylinder pressure and it was observed that there was an optimal post injection timing range for the maximum reduction of these parameters. The results also showed that an early post injection of butanol increased the nitrogen oxide emissions and an FTIR analysis revealed that late post injections increased the emissions of unburned butanol. The post injection duration sweep indicated that the peak pressure rise rate was significantly reduced by increasing the post injection duration at constant load conditions. There was also a reduction in the peak in-cylinder pressure. Measurements with a hydrogen mass spectrometer showed that there was an increased presence of hydrogen in the exhaust gas when the post injection duration was increased but the total yield of hydrogen was relatively low. It was observed that the coefficient of variation for the indicated mean effective pressure was significantly increased and that the indicated thermal efficiency was reduced when the post injection duration was increased. The results also showed that there were increased nitrogen oxide, carbon monoxide, and total hydrocarbon emissions for larger post injections. Although the use of a post injection resulted in emission and thermal efficiency penalties at medium load conditions, the results demonstrated that the post injection strategy successfully reduced the peak pressure rise rate and this characteristic can be potentially useful for higher load applications where the peak pressure rise rate is of greater concern.

Safe operation of dual-fuel engines using constrained stochastic control

2021 ◽  
pp. 146808742098510
Author(s):  
Carlos Guardiola ◽  
Benjamín Pla ◽  
Pau Bares ◽  
Alvin Barbier
Keyword(s):  
Pressure Rise ◽  
Maximum Amplitude ◽  
Dual Fuel ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Safe Operation ◽  
Pressure Oscillations ◽  
Engine Operation ◽  
Pressure Rise Rate ◽  
Rise Rate

Premixed combustion strategies have the potential to achieve high thermal efficiency and to lower the engine-out emissions such as NOx. However, the combustion is initiated at several kernels which create high pressure gradients inside the cylinder. Similarly to knock in spark ignition engines, these gradients might be responsible of important pressure oscillations with a harmful potential for the engine. This work aims to analyze the in-cylinder pressure oscillations in a dual-fuel combustion engine and to determine the feedback variables, control actuators, and control approach for a safe engine operation. Three combustion modes were examined: fully, highly, and partially premixed, and three indexes were analyzed to characterize the safe operation of the engine: the maximum pressure rise rate, the ringing intensity, and the maximum amplitude of pressure oscillations (MAPO). Results show that operation constraints exclusively based on indicators such as the pressure rise rate are not sufficient for a proper limitation of the in-cylinder pressure oscillations. This paper explores the use of a knock-like controller for maintaining the resonance index magnitude under a predefined limit where the gasoline fraction and the main injection timing were selected as control variables. The proposed strategy shows the ability to maintain the percentage of cycles exceeding the specified limit at a desired threshold at each combustion mode in all the cylinders.

Postinjection Strategy for the Reduction of the Peak Pressure Rise Rate of Neat n-Butanol Combustion

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Marko Jeftić ◽  
Ming Zheng
Keyword(s):  
Nitrogen Oxide ◽  
Thermal Efficiency ◽  
Peak Pressure ◽  
Pressure Rise ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Load Conditions

Enhanced premixed combustion of neat butanol in a compression ignition engine can have challenges with regards to the peak pressure rise rate (PRR) and the peak in-cylinder pressure. It was proposed to utilize a butanol postinjection to reduce the peak PRR and the peak in-cylinder pressure while maintaining a constant engine load. Postinjection timing and duration sweeps were carried out with neat n-butanol in a compression ignition engine. The postinjection timing sweep results indicated that the use of an early butanol postinjection reduced the peak PRR and the peak in-cylinder pressure and it was observed that there was an optimal postinjection timing range for the maximum reduction of these parameters. The results also showed that an early postinjection of butanol increased the nitrogen oxide emissions, and a Fourier transform infrared spectroscopy (FTIR) analysis revealed that late postinjections increased the emissions of unburned butanol. The postinjection duration sweep indicated that the peak PRR was significantly reduced by increasing the postinjection duration at constant load conditions. There was also a reduction in the peak in-cylinder pressure. Measurements with a hydrogen mass spectrometer showed that there was an increased presence of hydrogen in the exhaust gas when the postinjection duration was increased but the total yield of hydrogen was relatively low. It was observed that the coefficient of variation for the indicated mean effective pressure was significantly increased and that the indicated thermal efficiency was reduced when the postinjection duration was increased. The results also showed that there were increased nitrogen oxide, carbon monoxide, and total hydrocarbon (THC) emissions for larger postinjections. Although the use of a postinjection resulted in emission and thermal efficiency penalties at medium load conditions, the results demonstrated that the postinjection strategy successfully reduced the peak PRR, and this characteristic can be potentially useful for higher load applications where the peak PRR is of greater concern.

Performance of Dual Fuel Engine Running on Jojoba Oil as Pilot Fuel and CNG or LPG

2007 ◽  
Author(s):  
Mohamed Y. E. Selim ◽  
M. S. Radwan ◽  
H. E. Saleh
Keyword(s):  
Methyl Ester ◽  
Natural Gas ◽  
Pressure Rise ◽  
Combustion Noise ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Injection Timing ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Pilot Fuel

The use of Jojoba Methyl Ester as a pilot fuel was investigated for almost the first time as a way to improve the performance of dual fuel engine running on natural gas or LPG at part load. The dual fuel engine used was Ricardo E6 variable compression diesel engine and it used either compressed natural gas (CNG) or liquefied petroleum gas (LPG) as the main fuel and Jojoba Methyl Ester as a pilot fuel. Diesel fuel was used as a reference fuel for the dual fuel engine results. During the experimental tests, the following have been measured: engine efficiency in terms of specific fuel consumption, brake power output, combustion noise in terms of maximum pressure rise rate and maximum pressure, exhaust emissions in terms of carbon monoxide and hydrocarbons, knocking limits in terms of maximum torque at onset of knocking, and cyclic data of 100 engine cycle in terms of maximum pressure and its pressure rise rate. The tests examined the following engine parameters: gaseous fuel type, engine speed and load, pilot fuel injection timing, pilot fuel mass and compression ratio. Results showed that using the Jojoba fuel with its improved properties has improved the dual fuel engine performance, reduced the combustion noise, extended knocking limits and reduced the cyclic variability of the combustion.

Combustion parameter evaluation of diesel engine via vibration acceleration signal

2021 ◽  
pp. 146808742110308
Author(s):  
Pan Zhang ◽  
Wenzhi Gao ◽  
Yong Li ◽  
Zhaoyi Wei
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
Peak Position ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Combustion Control ◽  
Pressure Rise Rate ◽  
Acceleration Signal ◽  
Rise Rate ◽  
Start Of Combustion

Efficient combustion control has increasingly become a quality requirement for automobile manufacturers because of its impact on pollutant and greenhouse gas emissions. In view of this, the management system development of modern internal combustion engines is mainly aimed at combustion control. The real-time detection of in-cylinder pressure characteristic parameters has a considerable significance on the closed-loop combustion control of the internal combustion engine. This paper presents a detection method in which the start of combustion, peak pressure, maximum pressure rise rate, and phase of maximum pressure rise rate are identified through vibration acceleration signal. In order to analyze the relationship between vibration and in-cylinder pressure signal, experimental data are acquired in a diesel engine by implementing various injection strategies and engine operating conditions (speed and load). The results show that the start of combustion can be detected by analyzing its relationship with the peak position of the filtered vibration signal, and the phase of the maximum pressure rise rate can be identified by examining its relationship with the zero-cross position that is adjacent to the right of the peak position. Moreover, the filtered vibration signals are also truncated in the same length and utilized as inputs for algorithms to detect the peak pressure and the maximum pressure rise rate. The algorithms are mainly performed on data compression (or feature extraction) and target regression. Major algorithms, such as one-dimensional convolutional neural network, compression sensing, wavelet decomposition, multilayer perceptron, and support vector machine, are tested. Various experimental results verify that for the test engine the phase detection accuracy of the start of combustion and maximum pressure rise rate is less than 1.7°CA for a 95% prediction interval width. For the detection of the peak pressure and maximum pressure rise rate, the normalized error threshold is set as 0.05, then the accuracies can be not less than 95%.

scholarly journals Control-oriented premixed charge compression ignition CA50 model for a diesel engine utilizing variable valve actuation

2016 ◽  
Vol 18 (8) ◽  
pp. 847-857 ◽  
Author(s):  
Mayura H Halbe ◽  
David J Fain ◽  
Gregory M Shaver ◽  
Lyle Kocher ◽  
David Koeberlein
Keyword(s):  
Heat Release ◽  
Pressure Rise ◽  
Combustion Noise ◽  
Maximum Pressure ◽  
Compression Ignition ◽  
Estimation Strategy ◽  
Variable Valve Actuation ◽  
Rise Rate ◽  
Wide Range ◽  
Temperature Heat

Premixed charge compression ignition (PCCI) is a promising combustion strategy for reducing in-cylinder NOx and particulate matter formation in diesel engines without incurring fuel penalty. However, one of the challenges in PCCI implementation is that the process does not allow direct control of the combustion timing. The crank angle of 50% heat release, known as the CA50, is generally a reasonable proxy for the quality of combustion in terms of maximum pressure rise rate, combustion noise, and fuel conversion efficiency. This paper outlines the development, and validation, of a real-time capable estimation strategy for diesel-fueled PCCI CA50 using production-viable measurements that do not include in-cylinder pressure. The CA50 estimation strategy considers both stages of diesel-fueled PCCI combustion—low-temperature heat release and high-temperature heat release, which contributes most to the cumulative heat released during combustion. The strategy is validated using a PCCI CA50 dataset generated with a wide range of positions of a variable geometry turbocharge, exhaust gas recirculation fractions, and intake valve closing timings. The model estimates CA50 within ±2 CAD for 65 out of 80 data points and exhibits an error standard deviation of 2.55 CAD.

A New Criterion for Judging SI Engine In-Cylinder Pressure Development for Its Effect on Combustion Noise

1998 ◽  
Vol 120 (3) ◽  
pp. 664-668 ◽  
Author(s):  
J. Yang ◽  
R. W. Anderson
Keyword(s):  
Pressure Rise ◽  
Combustion Noise ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Si Engine ◽  
Rise Rate ◽  
Pressure Development ◽  
New Criterion ◽  
Measured Pressure ◽  
Lower Noise

The effect of engine in-cylinder pressure development on combustion noise is studied based on measured pressure traces and the attenuation-curve theory by Austen and Priede (1958). A new criterion is proposed that correlates better to the noise levels predicted by the attenuation theory than the commonly used maximum pressure rise rate. The effect of engine bore size on combustion noise is studied next with the same engine speed, the same piston mean speed, or the same power output, respectively. For the first two cases, a smaller bore size results in a lower noise level.

Sign in / Sign up

Export Citation Format

Share Document