Pressure Calculation From Experimentally Evaluated Lubricant Thickness Within EHL Contacts

2007 ◽  
Author(s):  
M. Vrbka ◽  
M. Vaverka ◽  
R. Poliscuk ◽  
I. Krupka ◽  
M. Hartl
Keyword(s):  
Film Thickness ◽  
Contact Pressure ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Solution Technique ◽  
Lubricant Film Thickness ◽  
Smooth Contact ◽  
Friction Surfaces

This paper is concerned with elastohydrodynamic lubrication, especially determination of lubricant film thickness and contact pressure within a point contact of friction surfaces of machine parts. A new solution technique for numerical determination of contact pressure is introduced. Direct measurement of contact pressure is very difficult. Hence, input data of lubricant film thickness obtained from the experiment based on colorimetric interferometry are used for calculation of pressure using the inverse elasticity theory. The algorithm is enhanced by convolution in order to increase calculation speed. The approach gives credible results on smooth contact and it is currently extended to enable the study of contact of friction surfaces with dents.

PTFE and MoS2 Additives for Mineral Oil Film Formation in EHL Point Contacts

2016 ◽  
Author(s):  
Glenn Kwabena Gyimah ◽  
Zhongning Guo ◽  
Ping Huang ◽  
Shuzhen Jiang ◽  
Gary C. Barber
Keyword(s):  
Film Thickness ◽  
Viscosity Index ◽  
Point Contact ◽  
Rolling Speed ◽  
Optical Interferometry ◽  
Lubricant Film ◽  
Steel Ball ◽  
Engine Oil ◽  
Lubricant Film Thickness ◽  
Viscosity Index Improvers

Lubricant film-forming viscosity index improvers blended with commercial engine oil have been developed and studied by using optical interferometry. The influence of the viscosity index improvers (PTFE and MoS2) mixed with oil were experimentally studied and compared with engine oil without the index improvers as the baseline. The effect of the viscosity index improvers on lubricant film thickness, contact pressure and rolling speed for the case of a steel ball loaded on a flat glass surface in point contact condition was investigated. An optical interferometry technique which utilized a monochromatic two-beam interferometry light source, a microscope and a high-speed video recording device was used for the investigation. Hamrock and Dawson calculations for EHL film thickness were also used for comparative analysis. The lubricants used were commercial SAE #30 engine oil and PTFE and MoS2 mixed with commercial SAE #30 engine oil. The oil viscosities ranged from 0.0109 Pa.s to 0.255 Pa.s. The rolling speed and the loads were varied between 0.189 m/s to 0.641 m/s and 1 N to 2.6 N respectively. The lubricant film thickness stability at the point of contact between the steel ball and the glass disc was investigated for both steady and rolling state conditions. The viscosity index improvers were found to have a significant effect on the film thickness behavior under pure rolling point contact conditions.

A Mixed-Lubrication Study of Journal Bearing Conformal Contacts

1997 ◽  
Vol 119 (3) ◽  
pp. 456-461 ◽  
Author(s):  
Qian (Jane) Wang ◽  
Fanghui Shi ◽  
Si C. Lee
Keyword(s):  
Film Thickness ◽  
Contact Pressure ◽  
Contact Area ◽  
Numerical Solutions ◽  
Mixed Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Asperity Contact ◽  
Lubricant Film Thickness ◽  
Asperity Contacts

Numerical analyses of finite journal bearings operating with large eccentricity ratios were conducted to better understand the mixed lubrication phenomena in conformal contacts. The average Reynolds equation derived by Patir and Cheng was utilized in the lubrication analysis. The influence function, calculated numerically using the finite element method, was employed to compute the bearing deformation. The effects of bearing surface roughness were incorporated in the present analysis for the calculations of the asperity contact pressure and the asperity contact area. The numerical solutions of the hydrodynamic and asperity contact pressures, lubricant film thickness, and asperity contact area were evaluated based on a simulated bearing-journal geometry. The calculations revealed that the asperity contact pressure may vary significantly along both the width and the circumferential directions. It was also shown that the asperity contacts and the lubricant film thickness were strongly dependent on the bearing width, asperity orientation, and operating conditions.

A Three-Dimensional Model of Line-Contact Elastohydrodynamic Lubrication for Heterogeneous Materials with Inclusions

2016 ◽  
Vol 08 (02) ◽  
pp. 1650014 ◽  
Author(s):  
Kun Zhou ◽  
Qingbing Dong
Keyword(s):  
Film Thickness ◽  
Half Space ◽  
Surface Deformation ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Line Contact ◽  
Lubricant Film Thickness ◽  
Equivalent Inclusion Method ◽  
Surface Contact

This paper develops a three-dimensional (3D) model for a heterogeneous half-space with inclusions distributed periodically beneath its surface subject to elastohydrodynamic lubrication (EHL) line-contact applied by a cylindrical loading body. The model takes into account the interactions between the loading body, the fluid lubricant and the heterogeneous half-space. In the absence of subsurface inclusions, the surface contact pressure distribution, the half-space surface deformation and the lubricant film thickness profile are obtained through solving a unified Reynolds equation system. The inclusions are homogenized according to Eshelby’s equivalent inclusion method (EIM) with unknown eigenstrains to be determined. The disturbed half-space surface deformations induced by the subsurface inclusions or eigenstrains are iteratively introduced into the lubricant film thickness until the surface deformation finally converges. Both time-independent smooth surface contact and time-dependent rough surface contact are considered for the lubricated contact problem.

Three-Dimensional Temperature Distribution in EHD Lubrication: Part II—Point Contact and Numerical Formulation

1993 ◽  
Vol 115 (1) ◽  
pp. 36-45 ◽  
Author(s):  
Kyung-Hoon Kim ◽  
Farshid Sadeghi
Keyword(s):  
Temperature Distribution ◽  
Film Thickness ◽  
Numerical Study ◽  
Control Volume ◽  
Three Dimensional ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Numerical Formulation ◽  
Energy Equations

A numerical study of Newtonian thermal elastohydrodynamic lubrication (EHD) of rolling/sliding point contacts has been conducted. The two-dimensional Reynolds, elasticity and the three-dimensional energy equations were solved simultaneously to obtain the pressure, film thickness and temperature distribution within the lubricant film. The control volume approach was employed to discretize the differential equations and the multi-level multi-grid technique was used to simultaneously solve them. The discretized equations, as well as the nonorthogonal coordinate transformation used for the solution of the energy equation, are described. The pressure, film thickness and the temperature distributions, within the lubricant film at different loads, slip conditions and ellipticity parameters are presented.

Lubricant Film Thickness and Wear in Rolling Point Contact

1965 ◽  
Vol 8 (4) ◽  
pp. 411-424 ◽  
Author(s):  
T. E. Tallian ◽  
E. F. Brady ◽  
J. I. McCool ◽  
L. B. Sibley
Keyword(s):  
Film Thickness ◽  
Point Contact ◽  
Lubricant Film ◽  
Lubricant Film Thickness
Sign in / Sign up

Export Citation Format

Share Document