A Mixed-Lubrication Study of Journal Bearing Conformal Contacts

1997 ◽  
Vol 119 (3) ◽  
pp. 456-461 ◽  
Author(s):  
Qian (Jane) Wang ◽  
Fanghui Shi ◽  
Si C. Lee
Keyword(s):  
Film Thickness ◽  
Contact Pressure ◽  
Contact Area ◽  
Numerical Solutions ◽  
Mixed Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Asperity Contact ◽  
Lubricant Film Thickness ◽  
Asperity Contacts

Numerical analyses of finite journal bearings operating with large eccentricity ratios were conducted to better understand the mixed lubrication phenomena in conformal contacts. The average Reynolds equation derived by Patir and Cheng was utilized in the lubrication analysis. The influence function, calculated numerically using the finite element method, was employed to compute the bearing deformation. The effects of bearing surface roughness were incorporated in the present analysis for the calculations of the asperity contact pressure and the asperity contact area. The numerical solutions of the hydrodynamic and asperity contact pressures, lubricant film thickness, and asperity contact area were evaluated based on a simulated bearing-journal geometry. The calculations revealed that the asperity contact pressure may vary significantly along both the width and the circumferential directions. It was also shown that the asperity contacts and the lubricant film thickness were strongly dependent on the bearing width, asperity orientation, and operating conditions.

Film Thickness and Friction Measurement of Piston Ring Cylinder Liner Contact With Corresponding Modeling Including Mixed Lubrication

2004 ◽  
Author(s):  
Nathan W. Bolander ◽  
Brian D. Steenwyk ◽  
Ashwin Kumar ◽  
Farshid Sadeghi
Keyword(s):  
Film Thickness ◽  
Analytical Model ◽  
Piston Ring ◽  
Cylinder Liner ◽  
Mixed Lubrication ◽  
Lubricant Film ◽  
Asperity Contact ◽  
Lubricant Film Thickness ◽  
Lubrication Regimes ◽  
Experimental Apparatus

An experimental apparatus and an analytical model have been developed to investigate and determine the lubrication condition and frictional losses at the interface between a piston ring and cylinder liner. The experimental apparatus features twin fiber optic displacement sensors to accurately measure the lubricant film thickness and a tri-axial piezoelectric force transducer to simultaneously measure frictional force. An analytical mixed lubrication model featuring Elrod cavitation and a stochastic/deterministic approach for asperity contact was used to investigate the effects of boundary and mixed lubrication conditions at the ends-of-stroke. A comparison between experimental and analytical results indicated that they are in good agreement. The results illustrate the transition through all of the different lubrication regimes (i.e. boundary, mixed and hydrodynamic lubrication) the piston ring and liner experience during a stroke. The twin displacement sensor arrangement is capable of producing accurate, repeatable measurements of lubricant film thickness that are in agreement with the analytical predictions. The analytical model developed for this study can capture the different lubrication regimes that the piston ring and liner experience.

Lubrication of 2D Soft Elasto Hydrodynamic Contacts: Extension of the Amplitude Reduction Theory

2011 ◽  
Author(s):  
F. Mora ◽  
P. Sainsot ◽  
A. A. Lubrecht ◽  
Y. le Chenadec
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Quantitative Prediction ◽  
Reduction Theory ◽  
Lubricant Film Thickness

This paper is an extension of the Amplitude Reduction Theory to soft ElastoHydrodynamic contacts. The ART permits a quantitative prediction of the influence of surface roughness on the lubricant film thickness modification as a function of the operating conditions.

Film Thickness Study of Lubricated, Compliant Contacts

2009 ◽  
Author(s):  
C. Myant ◽  
H. A. Spikes
Keyword(s):  
Film Thickness ◽  
Contact Area ◽  
Lubricant Film ◽  
Challenging Problem ◽  
Lubricant Film Thickness ◽  
Measuring Range ◽  
Metallic Contacts ◽  
Wide Range ◽  
High Roughness ◽  
Range Of Values

Obtaining lubricant film thickness values within a compliant contact is a challenging problem for several reasons [1]: • Lubricant film thickness covers a wide range of values. • The required measuring range is from fractions to hundreds of microns. • Contact area is considerably large when compared to “hard”, metallic contacts. • Many soft components have a high roughness compared to surfaces usually investigated with established techniques.

scholarly journals The Effect of Texture Floor Profile on the Lubricant Film Thickness in a Textured Hard-On-Soft Bearing With Relevance to Prosthetic Hip Implants

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Quentin Allen ◽  
Bart Raeymaekers
Keyword(s):  
Film Thickness ◽  
Polyethylene Wear ◽  
Texture Feature ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Design Parameters ◽  
Contact Friction ◽  
Hip Implants ◽  
Lubricant Film Thickness ◽  
Texture Parameters

Abstract Polyethylene wear debris limits the longevity of prosthetic hip implants. We design a pattern of axisymmetric texture features to increase hydrodynamic pressure and lubricant film thickness and, thus, reduce solid-on-solid contact, friction, and wear in hard-on-soft prosthetic hip implant bearings. Specifically, we study the effect of the texture floor profile on the lubricant film thickness using a soft elastohydrodynamic lubrication model. We compute the optimum texture parameters that maximize the lubricant film thickness for different texture floor profiles, as a function of bearing operating conditions. Flat texture floor profiles create thicker lubricant films than sloped or curved texture floor profiles for their respective optimum texture design parameters. We find that the texture feature volume is the most important parameter in terms of maximizing the lubricant film thickness, because a linear relationship exists between the texture feature volume with optimum texture parameters and the corresponding optimum lubricant film thickness, independent of the texture floor profile.

scholarly journals Maximizing the Lubricant Film Thickness Between a Rigid Microtextured and a Smooth Deformable Surface in Relative Motion, Using a Soft Elasto-Hydrodynamic Lubrication Model

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Quentin Allen ◽  
Bart Raeymaekers
Keyword(s):  
Film Thickness ◽  
Hydrodynamic Lubrication ◽  
Elastohydrodynamic Lubrication ◽  
Hydrodynamic Pressure ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Design Parameters ◽  
Lubricant Film Thickness ◽  
Texture Density ◽  
Film Lubrication

Abstract We design a pattern of microtexture features to increase hydrodynamic pressure and lubricant film thickness in a hard-on-soft bearing. We use a soft elastohydrodynamic lubrication model to evaluate the effect of microtexture design parameters and bearing operating conditions on the resulting lubricant film thickness and find that the maximum lubricant film thickness occurs with a texture density between 10% and 40% and texture aspect ratio between 1% and 14%, depending on the bearing load and operating conditions. We show that these results are similar to those of hydrodynamic textured bearing problems because the lubricant film thickness is almost independent of the stiffness of the bearing surfaces in full-film lubrication.

scholarly journals Numerical Simulation of a Slipper Model with Multi-Lands and Grooves for Hydraulic Piston Pumps and Motors in Mixed Lubrication

Lubricants ◽  
2019 ◽  
Vol 7 (7) ◽  
pp. 55
Author(s):  
Toshiharu Kazama
Keyword(s):  
Numerical Simulation ◽  
Contact Pressure ◽  
Power Loss ◽  
Numerical Solutions ◽  
Friction Torque ◽  
Mixed Lubrication ◽  
Operating Conditions ◽  
Axial Piston Pumps ◽  
Wide Range ◽  
Axial Piston

A theoretical model of a slipper with multi-lands and multi-grooves for swashplate type axial piston pumps and motors was established, including surface interactions. Further, a numerical simulation was conducted under an unsteady state and mixed lubrication conditions. Four model configurations were considered: A slipper with a single main land; a slipper with inner and main lands and a groove; a slipper with outer and main lands and a groove; and a slipper with inner, main, and outer lands with two grooves. Numerical solutions were obtained across a wide range of operating conditions in terms of center clearance, pad attitude, contact pressure, flow rate, friction torque, power loss, and stiffness. The motion and characteristics were differentiated into two groups: Slippers with a single-land and an annex inner-land; and slippers with an annex outer-land and a triple-land. The single-land and annex inner-land slippers exhibited smaller pad swing, whereas the triple-land and annex outer-land slippers reduced contact pressure and power loss.

scholarly journals On the Temperature and Lubricant Film Thickness Distribution in EHL Contacts with Arbitrary Entrainment

Lubricants ◽  
2018 ◽  
Vol 6 (4) ◽  
pp. 101 ◽  
Author(s):  
Milan Omasta ◽  
Jakub Adam ◽  
Petr Sperka ◽  
Ivan Krupka ◽  
Martin Hartl
Keyword(s):  
Film Thickness ◽  
Thermal Effects ◽  
Film Formation ◽  
Thickness Distribution ◽  
Thickness Measurement ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Lubricant Film Thickness ◽  
Machine Parts ◽  
Film Thickness Measurement

An understanding of mechanisms which are responsible for elastohydrodynamic lubricant film formation under high sliding conditions is necessary to increase durability of machine parts. This work combines thin-film colorimetric interferometry for lubricant film thickness measurement and infrared microscopy for in-depth temperature mapping through the contact. The results describe the effect of operating conditions such as speed, slide-to-roll ratio, ambient temperature, and sliding direction on lubricant film thickness and temperature distribution. Film thickness data shows how much the film shape is sensitive to operating conditions when thermal effects are significant, while the temperature profiles provides an explanation of this behavior.

Pressure Calculation From Experimentally Evaluated Lubricant Thickness Within EHL Contacts

2007 ◽  
Author(s):  
M. Vrbka ◽  
M. Vaverka ◽  
R. Poliscuk ◽  
I. Krupka ◽  
M. Hartl
Keyword(s):  
Film Thickness ◽  
Contact Pressure ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Solution Technique ◽  
Lubricant Film Thickness ◽  
Smooth Contact ◽  
Friction Surfaces

This paper is concerned with elastohydrodynamic lubrication, especially determination of lubricant film thickness and contact pressure within a point contact of friction surfaces of machine parts. A new solution technique for numerical determination of contact pressure is introduced. Direct measurement of contact pressure is very difficult. Hence, input data of lubricant film thickness obtained from the experiment based on colorimetric interferometry are used for calculation of pressure using the inverse elasticity theory. The algorithm is enhanced by convolution in order to increase calculation speed. The approach gives credible results on smooth contact and it is currently extended to enable the study of contact of friction surfaces with dents.

Ultrasonic Measurement of Rolling Bearing Lubrication Using Piezoelectric Thin Films

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Bruce W. Drinkwater ◽  
Jie Zhang ◽  
Katherine J. Kirk ◽  
Jocelyn Elgoyhen ◽  
Rob S. Dwyer-Joyce
Keyword(s):  
Film Thickness ◽  
High Frequency ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Rolling Element Bearing ◽  
Lubricant Layer ◽  
Lubricant Film Thickness ◽  
Oil Film ◽  
Deep Groove ◽  
Lubricated Contact

This paper describes the measurement of lubricant-film thickness in a rolling element bearing using a piezoelectric thin film transducer to excite and receive ultrasonic signals. High frequency (200 MHz) ultrasound is generated using a piezoelectric aluminum nitride film deposited in the form of a very thin layer onto the outer bearing raceway. This creates a transducer and electrode combination of total thickness of less than 10 μm. In this way the bearing is instrumented with minimal disruption to the housing geometry and the oil-film can be measured noninvasively. The high frequency transducer generates a fine columnar beam of ultrasound that has dimensions less than the typical lubricated contact ellipse. The reflection coefficient from the lubricant-layer is then measured from within the lubricated contact and the oil-film thickness extracted via a quasistatic spring model. The results are described on a deep groove 6016 ball bearing supporting an 80 mm shaft under normal operating conditions. Good agreement is shown over a range of loads and speeds with lubricant-film thickness extracted from elastohydrodynamic lubrication theory.

Sign in / Sign up

Export Citation Format

Share Document