Three Dimensional Elastic-Plastic Contact of Nominally Flat Rough Surfaces Based on FEA-Based Constitutive Asperity Contact Relations and Including Asperity Shoulder Contact

2008 ◽  
Author(s):  
A. Sepehri ◽  
K. Farhang
Keyword(s):  
Contact Force ◽  
Rough Surfaces ◽  
Constitutive Relations ◽  
Three Dimensional ◽  
Cumulative Effect ◽  
Element Model ◽  
Tangential Component ◽  
Normal Direction ◽  
Asperity Contact ◽  
Elastic Plastic

Three dimensional elastic-plastic contact of two nominally flat rough surfaces is considered. Equations governing the shoulder-shoulder contact of asperities are derived based on the asperity-asperity constitutive relations from a finite element model of their elastic-plastic interaction proposed by Kogut and Etsion [12]. Shoulder-shoulder asperity contact yields a slanted contact force consisting of both tangential (parallel to mean plane) and normal components. An analytical fusion technique is developed to combine the piecewise asperity level constitutive relations. This is shown to yield upon statistical summation the cumulative effect resulting in the contact force between two rough surfaces with two components, one in the normal direction and a half-plane tangential component.

Approximate Macroscale Constitutive Relations Using a Finite Element Based Constitutive Equations for Microscale Contact

2008 ◽  
Author(s):  
Ali Sepehri ◽  
Kambiz Farhang
Keyword(s):  
Finite Element ◽  
Contact Force ◽  
Rough Surfaces ◽  
Constitutive Relations ◽  
Cumulative Effect ◽  
Element Model ◽  
Tangential Component ◽  
Total Force ◽  
Asperity Contact ◽  
Elastic Plastic

Three dimensional elastic-plastic contact of two nominally flat rough surfaces is considered. Equations governing the shoulder-shoulder contact of asperities are derived based on the asperity-asperity constitutive relations from a finite element model of their elastic-plastic interaction. Shoulder-shoulder asperity contact yields a slanted contact force consisting of both tangential (parallel to mean plane) and normal components. Multiscale modeling of the elastic-plastic rough surface contact is presented in which asperity-level FE-based constitutive relations are statistically summed to obtain total force in the normal and tangential direction. The equations derived are in the form of integral functions and provide expectation of contact force components between two rough surfaces. An analytical fusion technique is developed to combine the piecewise asperity level constitutive relations. This is shown to yield upon statistical summation the cumulative effect resulting in the contact force between two rough surfaces with two components, one in the normal direction and a half-plane tangential component.

scholarly journals A Finite Element-Based Elastic-Plastic Model for the Contact of Rough Surfaces

2011 ◽  
Vol 2011 ◽  
pp. 1-11 ◽  
Author(s):  
Ali Sepehri ◽  
Kambiz Farhang
Keyword(s):  
Finite Element ◽  
Contact Force ◽  
Contact Area ◽  
Rough Surfaces ◽  
Constitutive Relations ◽  
Element Model ◽  
Tangential Component ◽  
Asperity Contact ◽  
Elastic Plastic ◽  
Force Components

Three-dimensional elastic-plastic contact of two nominally flat rough surfaces is considered. Equations governing the shoulder-shoulder contact of asperities are derived based on the asperity constitutive relations from a finite element model of the elastic-plastic interaction proposed by Kogut and Etsion (2002), in which asperity scale constitutive relations are derived using piecewise approximate functions. An analytical fusion technique is developed to combine the piecewise asperity level constitutive relations. Shoulder-shoulder asperity contact yields a slanted contact force consisting of two components, one in the normal direction and a half-plane tangential component. Statistical summation of the asperity level contact force components and asperity level contact area results in the total contact force and total contact area formulae between two rough surfaces. Approximate equations are developed in closed form for contact force components and contact area.

Closed-Form Equations for Three Dimensional Elastic-Plastic Contact of Nominally Flat Rough Surfaces

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Ali Sepehri ◽  
Kambiz Farhang
Keyword(s):  
Closed Form ◽  
Contact Force ◽  
Rough Surfaces ◽  
Tangential Force ◽  
Three Dimensional ◽  
Tangential Direction ◽  
Asperity Contact ◽  
Force Component ◽  
Elastic Plastic ◽  
Functional Forms

Approximate closed-form equations governing the shoulder-shoulder contact of asperities are derived based on a generalization by Chang, Etsion, and Bogy. The work entails the consideration of asperity shoulder-shoulder contact in which the volume conservation is assumed in the plastic flow regime. Shoulder-shoulder asperity contact gives rise to a slanted contact force comprising tangential and normal components. Each force component comprises elastic and plastic terms, which upon statistical summation yields the force component for the elastic and plastic forces for the contact of two rough surfaces. Half-plane tangential force due to elastic-plastic contact is derived through the statistical summation of tangential force component along an arbitrary tangential direction. Two sets of equations are found. In the first set of equations the functional forms are simpler and provide approximation of contact force to within 9%. The second set is enhanced equations derived from the first set of approximate equations that achieve an accuracy of within 0.2%.

Three Dimensional Elastic-Plastic Contact of Nominally Flat Rough Surfaces: Approximate Closed-Form Equations

2007 ◽  
Author(s):  
A. Sepehri ◽  
K. Farhang
Keyword(s):  
Closed Form ◽  
Contact Force ◽  
Rough Surfaces ◽  
Tangential Force ◽  
Three Dimensional ◽  
Tangential Direction ◽  
Asperity Contact ◽  
Force Component ◽  
Elastic Plastic ◽  
Form Closure

Approximate closed-form (closure) equations governing the shoulder-shoulder contact of asperities are derived based on a generalization of Chang, Etsion and Bogy (CEB). The work entails the consideration of asperity shoulder-shoulder contact in which volume conservation is assumed in the plastic flow regime. Shoulder-shoulder asperity contact gives rise to a slanted contact force comprising tangential and normal components. Each force component comprises elastic and elastic-plastic terms, which upon statistical summation yields the force component for the elastic and elastic-plastic force for the contact of two rough surfaces. Half-plane tangential force due to elastic-plastic contact is derived through the statistical summation of tangential force component along an arbitrary tangential direction. Two sets of closure equations are found. In the first set of equations the functional forms are simpler and provide approximation of contact force to within nine percent (9%). The second set of closure equations are closed form equations of more complicated form but with accuracy to within 0.2 percent (0.2%).

An Extension of CEB Elastic-Plastic Contact Model

2007 ◽  
Author(s):  
A. Sepehri ◽  
K. Farhang
Keyword(s):  
Contact Force ◽  
Tangential Force ◽  
Three Dimensional ◽  
Tangential Direction ◽  
Asperity Contact ◽  
Force Component ◽  
Normal Contact ◽  
Elastic Plastic ◽  
Force Components ◽  
Plastic Parts

Three dimensional elastic-plastic contact of two nominally flat rough surfaces is by developing the equations governing the shoulder-shoulder contact of asperities based on the Chang, Etsion and Bogy (CEB) model of contact in which volume conservation is assumed in the plastic flow regime. Shoulder-shoulder asperity contact yields a slanted contact force consisting of both tangential (parallel to mean plane) and normal components. Each force component comprises elastic and elastic-plastic parts. Statistical summation of normal force components leads to the derivation of the normal contact force for the elastic-plastic contact akin to the CEB model. Half-plane tangential force due to elastic-plastic contact is derived through the statistical summation of tangential force component along an arbitrary tangential direction.

Sliding Contact Analysis of Layered Elastic/Plastic Solids With Rough Surfaces

2001 ◽  
Vol 124 (1) ◽  
pp. 46-61 ◽  
Author(s):  
Wei Peng ◽  
Bharat Bhushan
Keyword(s):  
Surface Deformation ◽  
Rough Surfaces ◽  
Normal Load ◽  
Three Dimensional ◽  
Sliding Contact ◽  
Fast Fourier Transformation ◽  
Maximum Pressure ◽  
Asperity Contact ◽  
Elastic Plastic ◽  
Von Mises

A three-dimensional numerical model is presented to investigate the quasi-static sliding contact behavior of layered elastic/plastic solids with rough surfaces. The model is applicable for both single-asperity contact and multiple-asperity contacts. The surface deformation is obtained based on a variational principle. The surface and subsurface stresses in the layer and the substrate are determined with a Fast Fourier transformation (FFT) based scheme and von Mises and principal tensile stresses are computed accordingly. Contact statistics, such as fractional contact area, maximum pressure/E2 and relative meniscus force are predicted. The results are used to investigate the effect of the contact statistics on friction, stiction, and wear problems such as debris generation, brittle failure, and delamination of layered media. Optimum layer parameters are identified. It allows the specification of layer properties, according to the contact statistics, to reduce friction, stiction, and wear of materials. A normalization procedure is presented to apply the results on various combinations of surface roughness, material properties, and normal load.

Loading and Unloading Processes in Elastic-Plastic Contact of a Rough Surface With a Flat

2008 ◽  
Author(s):  
Ali Sepehri ◽  
Kambiz Farhang
Keyword(s):  
Contact Force ◽  
Tangential Force ◽  
Three Dimensional ◽  
Tangential Direction ◽  
Asperity Contact ◽  
Force Component ◽  
Normal Contact ◽  
Elastic Plastic ◽  
Force Components ◽  
Plastic Parts

Three dimensional elastic-plastic contact of two nominally flat rough surfaces is considered. Equations governing the shoulder-shoulder contact of asperities are derived based on the Chang, Etsion and Bogy (CEB) model of contact in which volume conservation is assumed in the plastic flow regime. Shoulder-shoulder asperity contact yields a slanted contact force consisting of both tangential (parallel to mean plane) and normal components. Each force component comprises elastic and elastic-plastic parts. Statistical summation of normal force components leads to the derivation of the normal contact force for the elastic-plastic contact akin to the CEB model. Half-plane tangential force due to elastic-plastic contact is derived through the statistical summation of tangential force component along an arbitrary tangential direction.

Reduced Rough-Surface Parametrization for Use With the Discrete-Element Model

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Stephen T. McClain ◽  
Jason M. Brown
Keyword(s):  
Heat Transfer ◽  
Rough Surface ◽  
Surface Characterization ◽  
Rough Surfaces ◽  
Roughness Element ◽  
Three Dimensional ◽  
Element Model ◽  
Discrete Element ◽  
Diameter Distribution ◽  
Discrete Element Model

The discrete-element model for flows over rough surfaces was recently modified to predict drag and heat transfer for flow over randomly rough surfaces. However, the current form of the discrete-element model requires a blockage fraction and a roughness-element diameter distribution as a function of height to predict the drag and heat transfer of flow over a randomly rough surface. The requirement for a roughness-element diameter distribution at each height from the reference elevation has hindered the usefulness of the discrete-element model and inhibited its incorporation into a computational fluid dynamics (CFD) solver. To incorporate the discrete-element model into a CFD solver and to enable the discrete-element model to become a more useful engineering tool, the randomly rough surface characterization must be simplified. Methods for determining characteristic diameters for drag and heat transfer using complete three-dimensional surface measurements are presented. Drag and heat transfer predictions made using the model simplifications are compared to predictions made using the complete surface characterization and to experimental measurements for two randomly rough surfaces. Methods to use statistical surface information, as opposed to the complete three-dimensional surface measurements, to evaluate the characteristic dimensions of the roughness are also explored.

Reduced Rough-Surface Parameterization for Use With the Discrete-Element Model

2007 ◽  
Author(s):  
Stephen T. McClain ◽  
Jason M. Brown
Keyword(s):  
Heat Transfer ◽  
Rough Surface ◽  
Surface Characterization ◽  
Rough Surfaces ◽  
Roughness Element ◽  
Three Dimensional ◽  
Element Model ◽  
Discrete Element ◽  
Diameter Distribution ◽  
Discrete Element Model

The discrete-element model for flows over rough surfaces was recently modified to predict drag and heat transfer for flow over randomly-rough surfaces. However, the current form of the discrete-element model requires a blockage fraction and a roughness-element diameter distribution as a function of height to predict the drag and heat transfer of flow over a randomly-rough surface. The requirement for a roughness element-diameter distribution at each height from the reference elevation has hindered the usefulness of the discrete-element model and inhibited its incorporation into a computational fluid dynamics (CFD) solver. To incorporate the discrete-element model into a CFD solver and to enable the discrete-element model to become a more useful engineering tool, the randomly-rough surface characterization must be simplified. Methods for determining characteristic diameters for drag and heat transfer using complete three-dimensional surface measurements are presented. Drag and heat transfer predictions made using the model simplifications are compared to predictions made using the complete surface characterization and to experimental measurements for two randomly-rough surfaces. Methods to use statistical surface information, as opposed to the complete three-dimensional surface measurements, to evaluate the characteristic dimensions of the roughness are also explored.

Contact Mechanics of Rough Surfaces in Tribology: Single Asperity Contact

1996 ◽  
Vol 49 (5) ◽  
pp. 275-298 ◽  
Author(s):  
Bharat Bhushan
Keyword(s):  
Friction And Wear ◽  
Rough Surfaces ◽  
Asperity Contact ◽  
Elastic Solids ◽  
Elastic Plastic ◽  
Single Asperity ◽  
Real Area Of Contact ◽  
Single Asperity Contact ◽  
Indentation Problem ◽  
Real Area

Contact modeling of two rough surfaces under normal approach and with relative motion is carried out to predict the real area of contact which affects friction and wear of an interface. The contact of two macroscopically flat bodies with microroughness is reduced to the contact at multiple asperities of arbitrary shapes. Most of deformation at the asperity contact can be either elastic or elastic-plastic. In this paper, a comprehensive review of modeling of a single asperity contact or an indentation problem is presented. Contact analyses for a spherical asperity/indenter on homogeneous and layered, elastic and elastic-plastic solids with and without tangential loading are presented. The analyses reviewed in this paper fall into two groups: (a) analytical solutions, primarily for elastic solids and (b) finite element solutions, primarily for elastic-plastic problems and layered solids. Implications of these analyses in friction and wear are discussed.

Sign in / Sign up

Export Citation Format

Share Document