Pre-Surgical Planning of Screw-Position Arrangement for the Femur Fractures With a Custom APP

2018 ◽  
Author(s):  
Chen-Yuan Chung ◽  
Jiing-Yih Lai ◽  
He-Kai Young ◽  
Han-Yuan Gao
Keyword(s):  
Computed Tomography ◽  
Finite Element ◽  
Stress Distribution ◽  
Surgical Planning ◽  
Bone Fractures ◽  
Element Model ◽  
Stress And Strain ◽  
Femur Fractures ◽  
Reference Information ◽  
Screw Position

Several types of implants, plates, and screws have been developed for corresponding bone fractures at different sites. To understand the mechanical behavior of a bone plate and to provide surgeons with suggestions for selecting screw positions, this study aimed to create an APP to provide pre-surgical planning using a computed tomography (CT)-based finite element model. This model was validated using a compression test of synthetic sawbones. Furthermore, the specific APP was established using the COMSOL application builder to calculate the stress and strain of the implant under different screw positions. This APP reveals how the number and location of screws affect the stress distribution of the implant. It can provide clinicians with preliminary reference information before surgery.

Research of the Connecting Form about the Spherical Shell and the Nozzle

2011 ◽  
Vol 413 ◽  
pp. 520-523
Author(s):  
Cai Xia Luo
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Finite Element Model ◽  
Spherical Shell ◽  
Maximum Stress ◽  
Peak Stress ◽  
Element Model ◽  
Small Opening ◽  
Large Opening ◽  
Reducing Stress

The Stress Distribution in the Connection of the Spherical Shell and the Opening Nozzle Is Very Complex. Sharp-Angled Transition and Round Transition Are Used Respectively in the Connection in the Light of the Spherical Shell with the Small Opening and the Large One. the Influence of the Two Connecting Forms on Stress Distribution Is Analyzed by Establishing Finite Element Model and Solving it. the Result Shows there Is Obvious Stress Concentration in the Connection. Round Transition Can Reduce the Maximum Stress in Comparison with Sharp-Angled Transition in both Cases of the Small Opening and the Large Opening, Mainly Reducing the Bending Stress and the Peak Stress, but Not the Membrane Stress. the Effect of Round Transition on Reducing Stress Was Not Significant. so Sharp-Angled Transition Should Be Adopted in the Connection when a Finite Element Model Is Built for Simplification in the Future.

Effect of Menisci Presence on Anterior Cruciate Ligament Stress and Strain in a Finite Element Model

2016 ◽  
Vol 48 ◽  
pp. 888 ◽  
Author(s):  
Edward Nyman ◽  
Marcel L. Ingels ◽  
Amirhesam Amerinatanzi ◽  
Rodney K. Summers ◽  
Timothy E. Hewett ◽  
...  
Keyword(s):  
Finite Element ◽  
Anterior Cruciate Ligament ◽  
Finite Element Model ◽  
Cruciate Ligament ◽  
Element Model ◽  
Stress And Strain ◽  
Anterior Cruciate

Finite-element modelling of thermo-mechanical stress distribution in laser beam ceramic tile grout sealing process

2006 ◽  
Vol 220 (10) ◽  
pp. 1497-1508 ◽  
Author(s):  
A Liaqat ◽  
S Safdar ◽  
M A Sheikh
Keyword(s):  
Thermal Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Laser Beam ◽  
Mechanical Stress ◽  
Ceramic Tile ◽  
Element Model ◽  
Ceramic Tiles ◽  
Temperature Dependent ◽  
Heat Effects

Laser tile grout sealing is a special process in which voids between the adjoining ceramic tiles are sealed by a laser beam. This process has been developed by Lawrence and Li using a customized grout material and a high power diode laser (HPDL). The process has been optimally carried out at laser powers of 60–120 W and at scanning speeds of 3–15 mm/s. Modelling of the laser tile grout sealing process is a complex task as it involves a moving laser beam and five different materials: glazed enamel, grout material, ceramic tile, epoxy bedding, and ordinary Portland cement substrate. This article presents the finite element model (FEM) of the laser tile grout sealing process. The main aim of this model is to accurately predict the thermo-mechanical stress distribution induced by the HPDL beam in the process. For an accurate representation of the process, the laser was modelled as a moving heat source. A three-dimensional transient thermal analysis was carried out to determine the temperature distribution. Temperature-dependent material properties and latent heat effects, due to melting and solidification of the glazed enamel, were taken into account in the FEM, thereby allowing a more realistic and accurate thermal analysis. The results of the thermal analysis were used as an input for the stress analysis with temperature-dependent mechanical properties. The results obtained from the FEM are compared with the published experimental results.

FINITE ELEMENT ANALYSIS OF A DENTAL IMPLANT

2003 ◽  
Vol 15 (02) ◽  
pp. 82-85 ◽  
Author(s):  
SHYH-CHOUR HUANG ◽  
CHANG-FENG TSAI
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Element Model ◽  
Element Analysis ◽  
3 Dimensional ◽  
Dimensional Finite Element ◽  
The Stability ◽  
Stress Concentration Effect ◽  
Implant System

This paper presents results from using a 3-dimensional finite element model to assess the stress distribution in the bone, in the implant and in the abutment as a function of the implant's diameter and length. Increasing implant diameter and length increases the stability of the implant system. By using a finite element analysis, we show that implant length does not decrease the stress distribution of either the implant or the bone. Alternatively, however implant diameter increases reduce the stresses. For the latter case, the contact area between implant and bone is increased thus the stress concentration effect is decreased. Also, with increased implant diameter the bone loss is decreased and as a consequence the success rate is improved.

Sign in / Sign up

Export Citation Format

Share Document