A Method to Identify the Crack Closure and Opening in Cyclic Tearing Tests on Fracture Mechanics Specimens

2014 ◽  
Author(s):  
B. Tranchand ◽  
V. Aubin ◽  
S. Marie
Keyword(s):  
Crack Closure ◽  
Kinematic Hardening ◽  
Crack Opening ◽  
Compact Tension ◽  
Compact Tension Specimen ◽  
Image Correlation ◽  
Electric Signal ◽  
Specimen Thickness ◽  
Secondary Circuit ◽  
Potential Measurement

To measure crack propagation in compact tension specimen, many methods can be used. The electric drop potential measurement is one of them and allows the detection of crack initiation. In our case, CT specimens, which have been taken from a carbon steel pipe (Tu42C) used in the secondary circuit of French PWR, are employed for cyclic tearing test. The detection of crack closure and crack opening should provide information for energetic analysis. However, the electric signal is unusable due to the cyclic loading. Indeed, because of the clearance between the pin and the specimen, each direction loading change causes a discontinuity in the signal. The roughness of the lips surface or the crack closure during compression loading returns also an unusual signal. Moreover, local measurement is required and there is high strain level around the crack tips, so strain gages are not suitable. Thus, displacement field are measured with digital image correlation and a specific image acquisition is employed. These methods allow a direct measurement of strain fields on the surface of the specimen. Thereby an interpretation of the previous electric signal and the crack opening and closure detection is realizable. Then, F.E. simulation, with non-linear kinematic hardening and node release method, are performed. These simulations allow the check of crack opening and closure detection through the specimen thickness.

Ductile Fracture Analysis Under Large Amplitude Cycles

2014 ◽  
Author(s):  
B. Tranchand ◽  
S. Chapuliot ◽  
V. Aubin ◽  
S. Marie ◽  
M. Bourgeois
Keyword(s):  
Crack Propagation ◽  
Fracture Energy ◽  
Ductile Fracture ◽  
Crack Closure ◽  
Large Amplitude ◽  
Crack Opening ◽  
Image Correlation ◽  
Potential Measurement ◽  
Loading Ratio

Demonstration of large components integrity under seismic loading is based up to now on monotonic tearing resistance curves. However, it is well known that cycles decrease the fracture resistance of the material, mainly according to the loading ratio. Most studies use monotonic methods to analyze reversible cyclic loading and the associated increase of crack propagation: Delta J-R curves are largely used. For monotonic loadings, Turner [1] proposed a decomposition of the rate of dissipated fracture energy. This decomposition led on the determination of an energetic criterion for ductile fracture [2]. This intrinsic criterion allows the fracture prediction on large components. This paper aims to propose an analysis of cyclic ductile fracture which should allow the determination of an energetic criterion under large amplitude cycles. For that purpose, compact tension specimens are taken from a carbon steel pipe (Tu42C) used in the secondary circuit of French PWR. A series of cyclic tearing tests are carried out under quasi-static loadings. The effects of loading ratio and incremental plastic displacement are quickly studied. Here, we present an energetic analysis which take into account the crack closure and crack opening. Indeed, displacement fields around the crack tips are measured with digital image correlation and linked with electric potential measurement. That allows an accurate determination of crack closure and crack opening and let a precise calculation of fracture energy possible. The energetic fracture criterion will be confirmed with crack propagation prediction on different geometry like CT specimen and a through-wall-cracked pipe under cyclic reversed loadings.

Influence of Sulfur Content on the Fracture Toughness Properties of 2 1/4 Percent Cr-1 Percent Mo Steel

1976 ◽  
Vol 98 (2) ◽  
pp. 135-142 ◽  
Author(s):  
J. F. Copeland
Keyword(s):  
Fracture Toughness ◽  
Sulfur Content ◽  
Detrimental Effect ◽  
Crack Opening ◽  
Analytical Techniques ◽  
Compact Tension ◽  
Compact Tension Specimen ◽  
Tension Specimen ◽  
Microvoid Coalescence ◽  
Opening Displacement

The effects of sulfur content on the fracture toughness properties of 2 1/4Cr-1 Mo steel were evaluated at test temperatures above, at, and below the nil ductility transition temperature (NDTT) of −23°C (−10°F). Small, 12.7-mm (0.5-in.) thick compact tension specimen results were combined with J-integral, Equivalent Energy, and Crack Opening Displacement analytical techniques to provide KIc results up to 22°C (72°F). It was found that the sulfur content of this steel has a large detrimental effect on KIc at the NDTT and above, where microvoid coalescence is the fracture mode. Sulfur has no significant effect at −73°C (−100°F) where cleavage occurs. These results also indicate that the higher Charpy V-notch energy at NDTT, shown by lower sulfur steels, is translatable into increased fracture resistance.

Compact tension fracture specimen: Experimental and computational implementations on stress intensity factor

2018 ◽  
Vol 53 (8) ◽  
pp. 630-647 ◽  
Author(s):  
Behzad V Farahani ◽  
Paulo J Tavares ◽  
Jorge Belinha ◽  
PMGP Moreira
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Interpolation Method ◽  
Compact Tension ◽  
Compact Tension Specimen ◽  
Image Correlation ◽  
The Finite Element Method ◽  
Point Interpolation Method ◽  
Point Interpolation

This work concentrates on the characterization of the stress intensity factor range for a compact tension specimen tested under a uniaxial tensile fatigue loading condition. The experimental solution is obtained using a three-dimensional full-field optical technique, digital image correlation. The deformation field is measured and documented for distinct crack lengths. As a relevant fracture parameter, stress intensity factor is thus experimentally measured combined with a computational overdeterministic algorithm for different crack lengths. Moreover, to verify the performance of the proposed fracture model, the cracked compact tension specimen is elasto-statically resolved using advanced discretization techniques, such as the finite element method, the meshless radial point interpolation method and the meshless natural neighbour radial point interpolation method. The finite element method model is thereby analysed with ABAQUS© to enable computation of mode I stress intensity factor results based on strain energy release rate criterion for different crack measurements in addition to strain contours. Likewise, the resolution pattern is repeated for meshless methods, and analogous numerical solutions are thus obtained. Overall, the experimental and numerical stress intensity factor results are compared with an available solution (ASTM E647) exhibiting a reasonable agreement. The novelty of this investigation is the amalgamation of an experimental digital image correlation procedure with a computational overdeterministic algorithm and, most importantly, the meshless formulation performance in the linear elastic fracture mechanics.

Fatigue Crack Propagation in Haynes 230: A Comparison between Single and Polycrystal Crack Closure Levels

2016 ◽  
Vol 258 ◽  
pp. 243-248 ◽  
Author(s):  
Stefano Beretta ◽  
Stefano Foletti ◽  
Silvio Rabbolini ◽  
Huseyin Sehitoglu
Keyword(s):  
Fatigue Crack ◽  
Crack Propagation ◽  
Crack Closure ◽  
Driving Forces ◽  
Crack Opening ◽  
Image Correlation ◽  
Accurate Estimation ◽  
Haynes 230 ◽  
Local Measurements ◽  
Plasticity Induced Crack Closure

An experimental campaign was developed to evaluate fatigue crack growth in Haynes 230. The effects of plasticity induced crack closure were investigated with Digital Image Correlation. In particular, crack opening levels were measured with the digital extensometer technique, which allowed the evaluation of crack flanks relative displacements. Experimental results were compared with a reference da/dn – ΔKeff curve and with the data of a previous study, which analyzed single crystal propagation. It was found that the adoption of crack closure local measurements provided an accurate estimation of crack propagation driving forces, since all the experimental points from single crystals and polycrystals collapse onto the da/dn – ΔKeff curve.

Experimental Investigation Into the Fracture Toughness of Polyethylene Pipe Material

2004 ◽  
Author(s):  
Ihab Mamdouh Graice ◽  
Maher Y. A. Younan ◽  
Soheir Ahmed Radwan Naga
Keyword(s):  
Fracture Toughness ◽  
Crack Opening ◽  
Experimental Tests ◽  
Compact Tension ◽  
Test Method ◽  
Elastic Behavior ◽  
Plastic Behavior ◽  
Specimen Thickness ◽  
Pipe Material ◽  
Opening Displacement

The mechanical behavior of the recently produced gas pipes material PE100 is investigated and compared to the commonly used material PE80 to determine their relative advantages. The two materials show plastic behavior at room temperature. The fracture toughness of the two materials is experimentally determined using the two common elastic plastic fracture mechanics methods: the ASTM multiple specimen test method for determining the J-R curve of the materials, and the crack opening displacement (COD) method. The investigation of the fracture behavior of the two materials includes the effect of the specimen thickness as well as specimen configuration. The experimental tests were carried on the compact tension (CT) specimens and the single edge notch bending (SENB) specimens. At −70°C, the materials show elastic behavior, the ASTM test method for determining fracture toughness is applied to SENB specimens to determine KIC of both materials. PE80 shows greater resistance to fracture than PE100.

Experimental Investigation Into the Fracture Toughness of Polyethylene Pipe Material

2005 ◽  
Vol 127 (1) ◽  
pp. 70-75 ◽  
Author(s):  
Ihab Mamdouh Graice ◽  
Maher Y. A. Younan ◽  
Soheir Ahmed Radwan Naga
Keyword(s):  
Fracture Toughness ◽  
Crack Opening ◽  
Experimental Tests ◽  
Compact Tension ◽  
Test Method ◽  
Elastic Behavior ◽  
Plastic Behavior ◽  
Specimen Thickness ◽  
Pipe Material ◽  
Opening Displacement

The mechanical behavior of the recently produced gas pipes material PE100 is investigated and compared to the commonly used material PE80 to determine their relative advantages. The two materials show plastic behavior at room temperature. The fracture toughness of the two materials is experimentally determined using the two common elastic plastic fracture mechanics methods: the American Society for Testing and Materials (ASTM) multiple specimen test method for determining the J-R curve of the materials, and the crack opening displacement method. The investigation of the fracture behavior of the two materials includes the effect of the specimen thickness as well as specimen configuration. The experimental tests were carried on the compact tension specimens and the single edge notch bending (SENB) specimens. At −70°C, the materials show elastic behavior, the ASTM test method for determining fracture toughness is applied to SENB specimens to determine KIC of both materials. PE80 shows greater resistance to fracture than PE100.

The Fined COD Transform Formula for CT Specimens to Investigate Material Fracture Toughness

2012 ◽  
Vol 188 ◽  
pp. 11-16
Author(s):  
Yao Yao ◽  
Li Xun Cai ◽  
Chen Bao ◽  
Han Jiang
Keyword(s):  
Crack Opening ◽  
Crack Tip ◽  
Compact Tension ◽  
Compact Tension Specimen ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Element Analysis ◽  
Material Fracture ◽  
Crack Tip Opening ◽  
The Relationship

For front-force compact tension specimen (FFCT), based on the refined results of the relationship between crack tip opening displacement and load line crack opening displacement from Finite Element Analysis (FEA), the influences of material properties and plastic deformation near the crack tip have been analyzed. A simplified and accurate transform formula for FFCT specimens is presented in this paper, and the error analysis is conducted.

Sign in / Sign up

Export Citation Format

Share Document