scholarly journals Influence of the phase difference between kinematic and inertial loads on seismic behaviour of pile foundations in layered soils

2020 ◽  
Author(s):  
Thejesh Kumar Garala ◽  
Gopal Madabhushi
Keyword(s):  
Natural Frequency ◽  
Free Field ◽  
Phase Relationship ◽  
Phase Variation ◽  
Bending Moment ◽  
Pile Group ◽  
Pile Foundations ◽  
Single Pile ◽  
Seismic Behaviour ◽  
Soil Layers

A series of dynamic centrifuge experiments was conducted on model pile foundations embedded in a two-layered soil profile consisted of soft-clay layer underlain by dense sand. These experiments were specifically designed to investigate the individual effect of kinematic and inertial loads on a single pile and a 3×1 row pile group during model earthquakes. It was observed that the ratio of free-field soil natural frequency to the natural frequency of structure might not govern the phase relationship between the kinematic and inertial loads for pile foundations as reported in some previous research. The phase relationship obtained in this study agrees well with the conventional phase variation between the force and displacement of a viscously damped simple oscillator subjected to a harmonic force. Further, as expected, the pile accelerations and bending moments can be smaller when the kinematic and inertial loads act against each other compared to the case when they act together on the pile foundations. This study also revealed that the peak kinematic pile bending moment will be at the interface of soil layers for both single pile and pile group. However, in the presence of both kinematic and inertial loads, the peak pile bending moment can occur either at the shallower depths or at the interface of soil layers depending on the pile cap rotational constraint.

Geometrical effects on the load transfer mechanism of pile groups: three-dimensional numerical analysis

2018 ◽  
Vol 55 (5) ◽  
pp. 749-757 ◽  
Author(s):  
Yaru Lv ◽  
Dongdong Zhang
Keyword(s):  
Load Transfer ◽  
Three Dimensional ◽  
Bending Moment ◽  
Pile Group ◽  
Transfer Mechanism ◽  
Single Pile ◽  
Pile Groups ◽  
Load Transfer Mechanism ◽  
Side Resistance ◽  
Geometrical Effects

This paper investigates geometrical effects on the load transfer mechanism of off-ground capped pile groups subjected to vertical load by four three-dimensional numerical simulations, including a circular single pile, an X-shaped cross-sectional concrete (XCC) single pile, a 4 × 4 circular pile group, and a 4 × 4 XCC pile group. The ultimate bearing capacities of the XCC and circular piles within pile groups are approximately 0.86 and 0.74 times that of the XCC and circular single piles, respectively. The group efficiency of the XCC pile group is mainly improved by its side resistance. Comparing the XCC pile group to the circular pile group, the increment in side resistance is almost larger than the increment in pile perimeter, indicating that the pile geometry alters the load transfer mechanism via stress concentration and lateral stress arching. A nonuniform load distribution on piles within a capped pile group causes a bending moment along the pile shafts. The bending moment of XCC piles is smaller than that of circular piles because the raft stiffness of an XCC pile group is increased by its larger circumscribing pile diameter.

Inelastic lateral and seismic behaviour of concrete-filled steel tubular pile foundations

2021 ◽  
Vol 143 ◽  
pp. 106657
Author(s):  
Dionisios N. Serras ◽  
Stamatia D. Panagaki ◽  
Konstantinos A. Skalomenos ◽  
George D. Hatzigeorgiou
Keyword(s):  
Pile Foundations ◽  
Seismic Behaviour

Seismic Response of Pile Groups Improved with Deep Cement mixing Columns in Liquefiable Sand: Shaking Table Tests

2021 ◽  
Author(s):  
Dingwen Zhang ◽  
Anhui Wang ◽  
Xuanming Ding
Keyword(s):  
Seismic Behavior ◽  
Lateral Displacement ◽  
Bending Moment ◽  
Pile Group ◽  
Shaking Table ◽  
Excess Pore Pressure ◽  
Shaking Table Tests ◽  
Pile Groups ◽  
Acceleration Response ◽  
Table Model

A series of shaking table model tests were performed to examine the effects of deep cement mixing (DCM) columns with different reinforcement depths on the seismic behavior of a pile group in liquefiable sand. Due to the DCM column reinforcement, the fundamental natural frequency of the model ground increases noticeably. The excess pore pressure of soils reduces with the increase of reinforcement depths of the DCM columns. Before liquefaction, the acceleration response of soils in the improved cases is obviously lower than that in the unimproved case, but the acceleration attenuation is greater after liquefaction in the unimproved case. Moreover, the lateral displacement of the superstructure, the settlement of the raft, and the bending moment of the piles in the improved cases are significantly reduced compared to those in the unimproved case, and the reduction ratios rise with the increase of reinforcement depth of the DCM columns. However, reinforcement by the DCM columns may result in the variation of the location of the maximum moment that occurs in the pile.

scholarly journals Comparison of Induced Deflection and Forces in Piles Adjacent to Tunnelling and Deep Excavation in 2D and 3D Problems

2018 ◽  
Vol 203 ◽  
pp. 04011
Author(s):  
Ong Yin Hoe ◽  
Hisham Mohamad
Keyword(s):  
Bending Moment ◽  
Pile Group ◽  
3D Models ◽  
Deep Excavation ◽  
Pile Groups ◽  
Out Of Plane ◽  
National University ◽  
Plane Direction ◽  
2D And 3D ◽  
2D Model

There is a trend in Malaysia and Singapore, engineers tend to model the effect of TBM tunneling or deep excavation to the adjacent piles in 2D model. In the 2D model, the pile is modelled using embedded row pile element which is a 1-D element. The user is allowed to input the pile spacing in out-of-plane direction. This gives an impression to engineers the embedded pile row element is able to model the pile which virtually is a 3D problem. It is reported by Sluis (2014) that the application of embedded pile row element is limited to 8D of pile length. It is also reported that the 2D model overestimates the axial load in pile and the shear force and bending moment at pile top and it is not realistic in comparison to 3D model. In this paper, the centrifuge results of single pile and 6-pile group - tunneling problem carried out in NUS (National University of Singapore) are back-analysed with Midas GTS 3D and a 2D program. In a separate case study, pile groups adjacent to a deep excavation is modelled by 3D and 2D program. This paper compares the deflection and forces in piles in 2D and 3D models.

Analysis of Ship Structural Loading in a Seaway

1972 ◽  
Vol 9 (02) ◽  
pp. 173-194
Author(s):  
Dan Hoffman
Keyword(s):  
Pressure Distribution ◽  
Phase Relationship ◽  
Bending Moment ◽  
Green Water ◽  
Detailed Structural Analysis ◽  
Transverse Pressure ◽  
Structural Loading ◽  
Wave Induced

The recent advent of the large tanker and bulk carrier has promoted the requirements for more detailed structural analysis of a ship and the reevaluation of theories for calculating the static, quasistatic and dynamic loads. The paper begins with discussion of the methods available to determine the various types of loads expected, their phase relationship, and ways of superimposing them. It then proceeds to the treatment of sea loads based on theoretical and experimental data, and techniques of determining the ship response in a seaway are discussed. The response to regular waves is reviewed with special reference to the determination of pressure distribution on the hull. Statistical ship response, immediate and cumulative over the life of the ship, is demonstrated in relation to the prediction of long-term bending moment trends, and the distribution of the extremes is discussed. Special loading conditions are described with special emphasis on the transverse pressure distribution, dynamic effects due to motion of liquid cargo in tanks, shipping of green water, wave-induced vibrations, slamming pressures and whipping stresses due to various causes. The paper treats the above subjects in a broad manner and no attempt to illustrate the theory in detail is made.

Simplified Analytical Solutions for Tunnel Settlement Induced by Axially Loading Single Pile and Pile Group

2021 ◽  
Vol 147 (12) ◽  
Author(s):  
Yixian Wang ◽  
Jian Liu ◽  
Panpan Guo ◽  
Wei Zhang ◽  
Hang Lin ◽  
...  
Keyword(s):  
Analytical Solutions ◽  
Pile Group ◽  
Single Pile

An experimental investigation into pile group-layered soil interaction

1996 ◽  
Vol 31 (5) ◽  
pp. 371-375
Author(s):  
K Chandrashekhara ◽  
S Joseph Antony ◽  
J Mallikarjuna Reddy
Keyword(s):  
Numerical Solutions ◽  
Interaction Analysis ◽  
Pile Group ◽  
Layered Soil ◽  
Single Pile ◽  
Photoelastic Method ◽  
Soil Medium ◽  
Interaction Factor ◽  
Pile Cap ◽  
Soil Interface

An interaction analysis of an axially loaded single pile and pile group with and without a pile cap in a layered soil medium has been investigated using the two-dimensional photoelastic method. A study of the pile or pile group behaviour has been made, varying the pile cap thickness as well as the embedded length of the pile in the hard stratum. The shear stress distribution along the pile-soil interface, non-dimensionalized settlement values of the single pile and the interaction factor for the pile group have been presented. Wherever possible, the results of the present analysis have been compared with available numerical solutions.

Dynamic analysis of laterally loaded pile groups in sand and clay

2002 ◽  
Vol 39 (6) ◽  
pp. 1358-1383 ◽  
Author(s):  
Yasser E Mostafa ◽  
M Hesham El Naggar
Keyword(s):  
Dynamic Loading ◽  
Dynamic Load ◽  
Load Transfer ◽  
Pile Group ◽  
Nonlinear Behaviour ◽  
Single Pile ◽  
Offshore Platforms ◽  
Group Effect ◽  
Pile Groups ◽  
Pile Head

Pile foundations supporting bridge piers, offshore platforms, and marine structures are required to resist not only static loading but also lateral dynamic loading. The static p–y curves are widely used to relate pile deflections to nonlinear soil reactions. The p-multiplier concept is used to account for the group effect by relating the load transfer curves of a pile in a group to the load transfer curves of a single pile. Some studies have examined the validity of the p-multiplier concept for the static and cyclic loading cases. However, the concept of the p-multiplier has not yet been considered for the dynamic loading case, and hence it is undertaken in the current study. An analysis of the dynamic lateral response of pile groups is described. The proposed analysis incorporates the static p–y curve approach and the plane strain assumptions to represent the soil reactions within the framework of a Winkler model. The model accounts for the nonlinear behaviour of the soil, the energy dissipation through the soil, and the pile group effect. The model was validated by analyzing the response of pile groups subjected to lateral Statnamic loading and comparing the results with field measured values. An intensive parametric study was performed employing the proposed analysis, and the results were used to establish dynamic soil reactions for single piles and pile groups for different types of sand and clay under harmonic loading with varying frequencies applied at the pile head. "Dynamic" p-multipliers were established to relate the dynamic load transfer curves of a pile in a group to the dynamic load transfer curves for a single pile. The dynamic p-multipliers were found to vary with the spacing between piles, soil type, peak amplitude of loading, and the angle between the line connecting any two piles and the direction of loading. The study indicated the effect of pile material and geometry, pile installation method, and pile head conditions on the p-multipliers. The calculated p-multipliers compared well with p-multipliers back-calculated from full scale field tests.Key words: lateral, transient loading, nonlinear, pile–soil–pile interaction, p–y curves, Statnamic.

Sign in / Sign up

Export Citation Format

Share Document