TEST STUDY ON THE BEST PASTING LAYER OF FRP REINFORCED CONCRETE

2019 ◽  
Vol 27 (02) ◽  
pp. 1950105
Author(s):  
XIANGQIAN FAN ◽  
JUEDING LIU
Keyword(s):  
Fracture Toughness ◽  
Acoustic Emission ◽  
Reinforced Concrete ◽  
Crack Depth ◽  
Mouth Opening ◽  
Bending Test ◽  
Crack Mouth Opening Displacement ◽  
Displacement Curve ◽  
Crack Mouth ◽  
Opening Displacement

To optimize the strengthening method using the fiber reinforced polymer (FRP) for the reinforcement of the concrete structure with cracks, the three-point bending test was conducted on the concrete beams wrapped with different layers of FRP materials. The strain gauges were pasted on the surface of the specimens to measure the initial cracking load. The crack mouth opening displacement (CMOD) was utilized to test the load–crack mouth opening displacement curve. According to the improved calculation formula of the fracture toughness, the critical effect crack length [Formula: see text], initiation fracture toughness [Formula: see text] and instability fracture toughness [Formula: see text] of specimens were calculated. The test results showed that, under the same initial crack depth, the peak load of FRP reinforced concrete decreases with the increase of FRP pasting layer. When there was one layer wrapped over the specimen, the instability toughness of the specimen reached the maximum value and the crack resistance was the best. Based on acoustic emission testing method, the acoustic emission parameters of the above-mentioned concrete during fracture process were identified and collected. The optimal layer of the FRP reinforced concrete with cracks was analyzed from the acoustic emission method.

Revised η-Factors for 3P SE(B) Fracture Specimens Incorporating 3-D Effects

2014 ◽  
Author(s):  
Rodolfo F. de Souza ◽  
Claudio Ruggieri
Keyword(s):  
Fracture Toughness ◽  
Mouth Opening ◽  
Estimation Procedure ◽  
Crack Mouth Opening Displacement ◽  
Evaluation Procedure ◽  
Specimen Thickness ◽  
Crack Mouth ◽  
Opening Displacement ◽  
Wide Range ◽  
Fracture Specimens

Standardized procedures to measure cleavage fracture toughness of ferritic steels in the DBT region most commonly employ three-point bend fracture specimens, conventionally termed SE(B) or SENB specimens. The evaluation protocol of fracture toughness for these crack configurations builds upon laboratory records of load and crack mouth opening displacement (CMOD) to relate plastic work with J (or, equivalently, CTOD). The experimental approach employs a plastic η-factor to relate the macroscale crack driving force to the area under the load versus crack mouth opening displacement for cracked configurations. This work provides revised η-factors derived from CMOD records applicable to estimate the J-integral and CTOD in SE(B) specimens with varying crack size and specimen configuration. Non-linear finite element analyses for plane-strain and 3-D models provide the evolution of load with increased CMOD which is required for the estimation procedure. The analysis matrix considers SE(B) specimens with W = 2B and W = B configurations with and without side grooves covering a wide range of specimen thickness, including precracked Charpy (PCVN) specimens. Overall, the present results provide further validation of the J and CTOD evaluation procedure currently adopted by ASTM 1820 while, at the same time, giving improved estimation equations for J incorporating 3-D effects which enter directly into more accurate testing protocols for experimental measurements of fracture toughness values using 3P SE(B) specimens.

Effect of Calcium Dissolution on the Fracture Properties of Concrete Exposed to Nitric Acid Environment

2011 ◽  
Vol 374-377 ◽  
pp. 1974-1978
Author(s):  
Hai Long Wang ◽  
Chun Ling Guo ◽  
Xiao Yan Sun
Keyword(s):  
Fracture Toughness ◽  
Nitric Acid ◽  
Mouth Opening ◽  
Crack Mouth Opening Displacement ◽  
Unstable Fracture ◽  
Crack Mouth ◽  
Acid Attack ◽  
Opening Displacement ◽  
Fracture Properties ◽  
Initial Fracture

The effect of calcium leaching by nitric acid on fracture properties of concrete was experimentally studied. The double-K fracture parameters were investigated using three-point bending beams, and the deterioration regularity of fracture properties of concrete chronically attacked by nitric acid was gotten on basis of these results. The load-crack mouth opening displacement curves under different nitric attack periods were obtained by pasting some strain gauges onto the pre-crack tip. On basis of the double-K criterion, the unstable fracture toughness as well as the initial fracture toughness was calculated according to the critical crack mouth opening displacement, the unstable fracture load and initial cracking load which can be obtained from the test. The experimental results indicated that the ratio of the initial fracture toughness to the unstable fracture toughness varied between 0.47 and 0.61 approximately. Both of the unstable fracture toughness and the initial fracture toughness decrease with attack period especially during the early 60 days, then drop to a stable trend gradually. In addition, the initial fracture toughness is less sensitive to acid attack compared with the unstable fracture toughness.

Experimental Observation of Front-Face-Displacement and Load-Line-Displacement in CT and Bend Specimens During Fracture Toughness Tests

2009 ◽  
Author(s):  
Bong-Sang Lee ◽  
Sang-Yoon Park ◽  
Min-Chul Kim
Keyword(s):  
Fracture Toughness ◽  
Mouth Opening ◽  
Crack Mouth Opening Displacement ◽  
Front Face ◽  
Analytical Relationship ◽  
Conservative Estimate ◽  
Crack Mouth ◽  
Opening Displacement ◽  
Load Line ◽  
Load Line Displacement

The master curve method described in ASTM E1921 provides a tool for using small specimens such as sub-sized CT and PCVN specimens for standard fracture toughness testing. However, a direct measurement of the load-line displacement of small specimens is not practical for standard fracture toughness tests. Mostly, the front-face displacement or the crack mouth opening displacement can be measured and converted into the load-line displacement by using an analytical relationship proposed by several investigators. Since those relationships were deduced from numerical calculations of the loaded specimens, experimental deviations may occur because of specimen indentation, rotation and arm bending during an actual testing. It is clear that the determination of fracture toughness is influenced by the accuracy of the estimation of load-line displacement as well as the load measurement. In this study, the relationship between the load-line displacement and the front-face displacement or the crack mouth displacement was investigated experimentally by using a series of CT and Bend specimens modified to measure the two displacements simultaneously during a single test. The results showed that the front-face measurement of CT specimens may result in about 3% more conservative estimate of fracture toughness. In the case of bend specimens, the crack mouth opening displacement measurement may result in about 7% non-conservative estimate of fracture toughness than the load-line measurement.

Experimental analysis of crack evolution in concrete by the acoustic emission technique

2015 ◽  
Author(s):  
J. Saliba ◽  
A. Loukili ◽  
J.P. Regoin ◽  
D. Grégoire ◽  
L. Verdon ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Fracture Process ◽  
Process Zone ◽  
Mouth Opening ◽  
Acoustic Emissions ◽  
Plain Concrete ◽  
Crack Mouth Opening Displacement ◽  
Notch Depth ◽  
Opening Displacement ◽  
Magnitude Distribution

The fracture process zone (FPZ) was investigated on unnotched and notched beams with different notch depths. Three point bending tests were realized on plain concrete under crack mouth opening displacement (CMOD) control. Crack growth was monitored by applying the acoustic emission (AE) technique. In order to improve our understanding of the FPZ, the width and length of the FPZ were followed based on the AE source locations maps and several AE parameters were studied during the entire loading process. The bvalue analysis, defined as the log-linear slope of the frequency-magnitude distribution of acoustic emissions, was also carried out to describe quantitatively the influence of the relative notch depth on the fracture process. The results show that the number of AE hits increased with the decrease of the relative notch depth and an important AE energy dissipation was observed at the crack initiation in unnotched beams. In addition, the relative notch depth influenced the AE characteristics, the process of crack propagation, and the brittleness of concrete.

scholarly journals Fracture Properties and Softening Curves of Steel Fiber-Reinforced Slag-Based Geopolymer Mortar and Concrete

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1445 ◽  
Author(s):  
Yao Ding ◽  
Yu-Lei Bai
Keyword(s):  
Fracture Toughness ◽  
Fracture Energy ◽  
Inverse Analysis ◽  
Steel Fiber ◽  
Mouth Opening ◽  
Crack Mouth Opening Displacement ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Opening Displacement ◽  
Fracture Properties

Adding short steel fibers into slag-based geopolymer mortar and concrete is an effective method to enhance their mechanical properties. The fracture properties of steel fiber-reinforced slag-based geopolymer concrete/mortar (SGC/SGM) and unreinforced control samples were compared through three-point bending (TPB) tests. The influences of steel fiber volume contents (1.0%, 1.5% and 2.0%) on the fracture properties of SGC and SGM were studied. Load-midspan deflection (P-δ) curves and load-crack mouth opening displacement (P-CMOD) curves of the tested beams were recorded. The compressive and splitting tensile strengths were also tested. The fracture energy, flexural strength parameters, and fracture toughness of steel fiber-reinforced SGC and SGM were calculated and analyzed. The softening curves of steel fiber-reinforced SGC and SGM were determined using inverse analysis. The experimental results show that the splitting tensile strength, fracture energy, and fracture toughness are significantly enhanced with fiber incorporation. A strong correlation between the equivalent and residual flexural strengths is also observed. In addition, the trilinear strain-softening curves obtained by inverse analysis predict well of the load-displacement curves recorded from TPB tests.

Crack Mouth Opening Displacement-Based η Factors for SE(B) Specimens

2009 ◽  
Vol 37 (4) ◽  
pp. 102116
Author(s):  
M. R. Mitchell ◽  
R. E. Link ◽  
J. P. Petti ◽  
R. H. Dodds, Jr. ◽  
R. E. Link
Keyword(s):  
Mouth Opening ◽  
Crack Mouth Opening Displacement ◽  
Crack Mouth ◽  
Opening Displacement ◽  
Displacement Based

scholarly journals Vibrated Concrete vs. Self-Compacting Concrete: Comparison of Fracture Mechanics Properties

2014 ◽  
Vol 601 ◽  
pp. 199-202
Author(s):  
Sara Korte ◽  
Veerle Boel ◽  
Wouter de Corte ◽  
Geert de Schutter
Keyword(s):  
Fracture Mechanics ◽  
Mouth Opening ◽  
Bending Test ◽  
Crack Mouth Opening Displacement ◽  
Self Compacting Concrete ◽  
Opening Displacement ◽  
Three Point Bending ◽  
Fracture Parameters ◽  
Wedge Splitting Test ◽  
Splitting Test

This study focuses on the fracture mechanics aspect of self-compacting concrete, compared to vibrated concrete. The most commonly used experiments to investigate the toughness and cracking behaviour of concrete are the three-point bending test (3PBT) on small, notched beams, and the wedge-splitting test (WST) on cubic samples with guiding groove and starter notch. From the resulting P-CMOD curves (applied load versus crack mouth opening displacement), different fracture parameters, such as fracture energy and fracture toughness, can be extracted. Moreover, using inverse analysis, the σ-w relationship (tensile stress versus crack width) can be derived. This paper lists the results of a series of tests on samples, made of VC, SCC of equal strength, and SCC with identical w/c factor. Subsequently, a comparison of the mechanical characteristics is made, revealing important differences regarding several fracture parameters.

Sign in / Sign up

Export Citation Format

Share Document