scholarly journals Improving Efficiency of Evaporated Cu2ZnSnS4Thin Film Solar Cells by a Thin Ag Intermediate Layer between Absorber and Back Contact

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Hongtao Cui ◽  
Chang-Yeh Lee ◽  
Wei Li ◽  
Xiaolei Liu ◽  
Xiaoming Wen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Carrier Transport ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Depletion Region ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Back Contact ◽  
Secondary Phases ◽  
P Type

A 20 nm Ag coating on Mo back contact was adopted to improve the back contact of evaporated Cu2ZnSnS4(CZTS) solar cells. The Ag layer helped reduce the thickness of MoS2which improves fill factor (FF) significantly; additionally, it reduced secondary phases ZnS and SnS2−x, which may help carrier transport; it was also involved in the doping of the absorber layer, which compensated the intrinsic p-type doping and therefore drags down the doping level. The doping involvement may enlarge the depletion region and improve lifetime of the absorber, which led to enhancing open circuit voltage (VOC), short circuit current density (JSC), and efficiency significantly. However, it degrades the crystallinity of the material slightly.

Simulation of Symmetrically Doped Silicon Nanowire Solar Cells

2011 ◽  
Vol 1322 ◽  
Author(s):  
Felix Voigt ◽  
Thomas Stelzner ◽  
Silke H. Christiansen
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Silicon Nanowire ◽  
Short Circuit Current ◽  
Cylindrical Symmetry ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Back Surface ◽  
Cell Efficiency ◽  
P Type

ABSTRACTSilicon nanowire solar cells were simulated using the Silvaco TCAD software kit. For optimization of speed the simulations were performed in cylinder coordinates with cylindrical symmetry. Symmetric doping was assumed with a dopant density of 1018 cm-3 in the p-type core and inside the n-type shell. In the implementation a cathode contact was wrapped around the semiconductor nanorod and an anode was assumed at the bottom of the rod. Optimization of cell efficiency was performed with regard to the rod radius and the rod length. In both optimization processes clear maxima in efficiency were visible, resulting in an optimal radius of 66 nm with the pn junction at 43.5 nm and an optimal rod length of about 48 μm. The maximum of efficiency with respect to the rod radius is due to a decrease of short-circuit current density (Jsc) and an increase of open-circuit voltage (Uoc) with radius, while the maximum with respect to the rod length is explained by the combination of an increase of Jsc and a decrease of Uoc. Fill factors stay rather constant at values between 0.6 and 0.8. Further, the influence of a back surface field (BSF) layer was surveyed in simulations. Positioning the BSF next to the cathode contact considerably improved cell efficiency. In addition, simulations with a cathode contact on top of the nanowire structure were undertaken. No severe deterioration of cell performance with increasing radius was observed so far in this configuration. Hence, nanorods with much larger radii can be used for solar cells using this contact scheme. In comparison to simulations with wrapped cathode contacts, Jsc and Uoc and therefore efficiency is considerably improved.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals Ultrathin Cu(In,Ga)Se2 Solar Cells with Ag/AlOx Passivating Back Reflector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4268
Author(s):  
Jessica de Wild ◽  
Gizem Birant ◽  
Guy Brammertz ◽  
Marc Meuris ◽  
Jef Poortmans ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Electron Microscopic ◽  
Current Increase ◽  
Time Resolved ◽  
Cigs Solar Cells

Ultrathin Cu(In,Ga)Se2 (CIGS) absorber layers of 550 nm were grown on Ag/AlOx stacks. The addition of the stack resulted in solar cells with improved fill factor, open circuit voltage and short circuit current density. The efficiency was increased from 7% to almost 12%. Photoluminescence (PL) and time resolved PL were improved, which was attributed to the passivating properties of AlOx. A current increase of almost 2 mA/cm2 was measured, due to increased light scattering and surface roughness. With time of flight—secondary ion mass spectroscopy, the elemental profiles were measured. It was found that the Ag is incorporated through the whole CIGS layer. Secondary electron microscopic images of the Mo back revealed residuals of the Ag/AlOx stack, which was confirmed by energy dispersive X-ray spectroscopy measurements. It is assumed to induce the increased surface roughness and scattering properties. At the front, large stains are visible for the cells with the Ag/AlOx back contact. An ammonia sulfide etching step was therefore applied on the bare absorber improving the efficiency further to 11.7%. It shows the potential of utilizing an Ag/AlOx stack at the back to improve both electrical and optical properties of ultrathin CIGS solar cells.

17.8%-efficient Amorphous Silicon Heterojunction Solar Cells on p-type Silicon Wafers

2006 ◽  
Vol 910 ◽  
Author(s):  
Qi Wang ◽  
Matt P. Page ◽  
Eugene Iwancizko ◽  
Yueqin Xu ◽  
Yanfa Yan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Amorphous Silicon ◽  
High Efficiency ◽  
Short Circuit ◽  
Open Circuit ◽  
Layer Growth ◽  
Surface Recombination Velocity ◽  
Back Contact ◽  
P Type

AbstractWe have achieved an independently-confirmed 17.8% conversion efficiency in a 1-cm2, p-type, float-zone silicon (FZ-Si) based heterojunction solar cell. Both the front emitter and back contact are hydrogenated amorphous silicon (a-Si:H) deposited by hot-wire chemical vapor deposition (HWCVD). This is the highest reported efficiency for a HWCVD silicon heterojunction (SHJ) solar cell. Two main improvements lead to our most recent increases in efficiency: 1) the use of textured Si wafers, and 2) the application of a-Si:H heterojunctions on both sides of the cell. Despite the use of textured c-Si to increase the short-circuit current, we were able to maintain the same 0.65 V open-circuit voltage as on flat c-Si. This is achieved by coating a-Si:H conformally on the c-Si surfaces, including covering the tips of the anisotropically-etched pyramids. A brief atomic H treatment before emitter deposition is not necessary on the textured wafers, though it was helpful in the flat wafers. It is essential to high efficiency SHJ solar cells that the emitter grows abruptly as amorphous silicon, instead of as microcrystalline or epitaxial Si. The contact on each side of the cell comprises a thin (< 5 nm) low substrate temperature (~100°C) intrinsic a-Si:H layer, followed by a doped layer. Our intrinsic layers are deposited at 0.3-1.2 nm/s. The doped emitter and back-contact layers were deposited at a higher temperature (>200°C) and grown from PH3/SiH4/H2 and B2H6/SiH4/H2 doping gas mixtures, respectively. This combination of low (intrinsic) and high (doped layer) growth temperatures was optimized by lifetime and surface recombination velocity measurements. Our rapid efficiency advance suggests that HWCVD may have advantages over plasma-enhanced (PE) CVD in fabrication of high-efficiency heterojunction c-Si cells; there is no need for process optimization to avoid plasma damage to the delicate, high-quality, Si wafers.

scholarly journals Effects of Different Doping Ratio of Cu Doped CdS on QDSCs Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-4
Author(s):  
Xiaojun Zhu ◽  
Xiaoping Zou ◽  
Hongquan Zhou
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Sensitized Solar Cells ◽  
Doping Ratio

We use the successive ionic layer adsorption and reaction (SILAR) method for the preparation of quantum dot sensitized solar cells, to improve the performance of solar cells by doping quantum dots. We tested the UV-Vis absorption spectrum of undoped CdS QDSCs and Cu doped CdS QDSCs with different doping ratios. The doping ratios of copper were 1 : 100, 1 : 500, and 1 : 1000, respectively. The experimental results show that, under the same SILAR cycle number, Cu doped CdS quantum dot sensitized solar cells have higher open circuit voltage, short circuit current density photoelectric conversion efficiency than undoped CdS quantum dots sensitized solar cells. Refinement of Cu doping ratio are 1 : 10, 1 : 100, 1 : 200, 1 : 500, and 1 : 1000. When the proportion of Cu and CdS is 1 : 10, all the parameters of the QDSCs reach the minimum value, and, with the decrease of the proportion, the short circuit current density, open circuit voltage, and the photoelectric conversion efficiency are all increased. When proportion is 1 : 500, all parameters reach the maximum values. While with further reduction of the doping ratio of Cu, the parameters of QDSCs have a decline tendency. The results showed that, in a certain range, the lower the doping ratio of Cu, the better the performance of quantum dot sensitized solar cell.

Solar Cell Contacts Using Nano-Sized Dispersions

1999 ◽  
Vol 581 ◽  
Author(s):  
Doug Schulz ◽  
R. Ribelin ◽  
X. Wu ◽  
K.M. Jones ◽  
R.J. Matson ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spray Deposition ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Cdte Layer ◽  
Open Circuit ◽  
Alloy Formation ◽  
Current Densities ◽  
P Type ◽  
Open Circuit Voltages

ABSTRACTNano-sized dispersions have been employed as precursor inks for the spray deposition of contacts to both Si and CdTe materials. In the case of Si, nano-sized Al particles (nano-Al) were dispersed and spray deposited onto p-type Si. Annealing above the eutectic temperature causes alloy formation yielding a p+ layer with p ∼ 10−4 Ω•cm. For CdTe, nano-sized Te particles (nano-Te) were dispersed and sprayed onto CdTe/CdS/SnO2/glass heterostructures. Contact to the CdTe layer occurred during a 30 min anneal in He (T = 215 to 255 °C). These solar cells were finished by spin-coating the Te layer with Ag paint and subsequently annealing in air (100 °C / 1 h). This approach produces solar cells with open circuit voltages (Voc) from 720 to 800 mV, short circuit current densities (Jsc) from 18 to 20 mA/cm2 and efficiencies up to 10.3%. The performance of these cells was similar to those produced using the standard NREL contact.

scholarly journals SCAPS Simulation on P3HT:Graphene Nanocomposites Based Bulk-Heterojunction Organic Solar Cells

2019 ◽  
Vol 9 (1) ◽  
pp. 28
Author(s):  
Nur Shakina Mohd Shariff ◽  
Puteri Sarah Mohamad Saad ◽  
Mohamad Rusop Mahmood
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Bulk Heterojunction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Simulation Software ◽  
Capacitance Voltage

There has been an increasing interest towards organic solar cells after the discovery of conjugated polymer and bulk-heterojunction concept. Eventhough organic solar cells are less expensive than inorganic solar cells but the power conversion energy is still considered low. The main objective of this research is to investigate the effect of the P3HT’s thickness and concentration towards the efficiency of the P3HT:Graphene solar cells. A simulation software that is specialize for photovoltaic called SCAPS is used in this research to simulate the effect on the solar cells. The solar cell’s structure will be drawn inside the simulation and the parameters for each layers is inserted. The result such as the open circuit voltage (Voc), short circuit current density (Jsc), fill factor (FF), efficiency (η), capacitance-voltage (C-V) and capacitance-frequency (C-f) characteristic will be calculated by the software and all the results will be put into one graph.

scholarly journals Benzothiadiazole Based Cascade Material to Boost the Performance of Inverted Ternary Organic Solar Cells

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 450 ◽  
Author(s):  
Miron Krassas ◽  
Christos Polyzoidis ◽  
Pavlos Tzourmpakis ◽  
Dimitriοs M. Kosmidis ◽  
George Viskadouros ◽  
...  
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Ring ◽  
Electron Cascade ◽  
First Time

A conjugated, ladder-type multi-fused ring 4,7-dithienbenzothiadiazole:thiophene derivative, named as compound ‘T’, was for the first time incorporated, within the PTB7:PC71BM photoactive layer for inverted ternary organic solar cells (TOSCs) realization. The effective energy level offset caused by compound T between the polymeric donor and fullerene acceptor materials, as well as its resulting potential as electron cascade material contribute to an enhanced exciton dissociation, electron transfer facilitator and thus improved overall photovoltaic performance. The engineering optimization of the inverted TOSC, ITO/PFN/PTB7:Compound T(5% v/v):PC71BM/MoO3/Al, resulted in an overall power conversion efficiency (PCE) of 8.34%, with a short-circuit current density (Jsc) of 16.75 mA cm−2, open-circuit voltage (Voc) of 0.74 V and a fill factor (FF) of 68.1%, under AM1.5G illumination. This photovoltaic performance was improved by approximately 12% with respect to the control binary device.

Preparation of the Three Main Layers of CdS/CdTe Thin Film Solar Cells Using a Single Vacuum System

2011 ◽  
Vol 378-379 ◽  
pp. 601-605 ◽  
Author(s):  
Saleh N. Alamri ◽  
M. S. Benghanem ◽  
A. A. Joraid
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Silica ◽  
Vacuum System ◽  
Cdte Thin Film

This study investigates the preparation of the three main layers of a CdS/CdTe thin film solar cell using a single vacuum system. A Close Space Sublimation System was constructed to deposit CdS, CdTe and CdCl2 solar cell layers. Two hot plates were used to heat the source and the substrate. Three fused silica melting dishes were used as containers for the sources. The properties of the deposited CdS and CdTe films were determined via Atomic force microscopy, scanning electron microscopy, X-ray diffraction and optical transmission spectroscopy. An J-V characterization of the fabricated CdS/CdTe solar cells was performed under solar radiation. The short-circuit current density, Jsc, the open-circuit voltage, Voc, fill factor, FF and conversion efficiency, η, were measured and yielded values of 27 mA/cm2, 0.619 V, 58% and 9.8%, respectively.

RELIABILITY STUDIES OF P3HT: PCBM ORGANIC SOLAR CELLS FABRICATED WITH CALCIUM–ALUMINUM AND LITHIUM FLUORIDE–ALUMINIUM CATHODES

2011 ◽  
Vol 10 (04n05) ◽  
pp. 803-807
Author(s):  
T. S. KRISHNAN ◽  
S. SUNDAR KUMAR IYER
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Continuous Illumination ◽  
Stress Tests ◽  
Ambient Conditions ◽  
Over Time

This work addresses the shelf life characteristics of P3HT: PCBM blend based organic solar cells (OSC) fabricated with Ca–Al and LiF–Al cathodes. Some of these devices are encapsulated in nitrogen ambient and some in room ambient. Device electrical characteristics are studied under both dark and light. In the analysis under dark ambient conditions, the degradation in peak dark current is monitored over time (in days) and an empirical model is postulated for the degradation based on statistical curve fitting techniques. In the analysis under light, degradation of parameters such as fill factor (FF), open circuit voltage (V oc ) and short circuit current density (J sc ) is monitored over time in these devices (for different cathodes and different ambients) and the results are analyzed and compared. Also, accelerated stress tests are conducted wherein the devices are subjected to continuous illumination for a period of 1.5 h under two different intensities (0.76 sun and 1 sun) and again, the results are analyzed and compared. A model is fitted to the observed degradation in normalized J sc and the degradation constants (k deg ) are obtained. It is seen that the devices fabricated with cathode as LiF–Al and being encapsulated in nitrogen ambient provide the best performance over time.

Sign in / Sign up

Export Citation Format

Share Document