Non-contact detection of polyester filament yarn tension in the spinning process by the laser Doppler vibrometer method

2021 ◽  
pp. 004051752110342
Author(s):  
Dongjian Zhang ◽  
Qihua Ma ◽  
Yuan Tan ◽  
He Liao ◽  
Chenhui Lu ◽  
...  

The precise detection of polyester filament yarn (PFY) tension in the spinning process is critical to ensure product quality. The laser Doppler vibrometer (LDV) method is proposed to achieve non-contact detection of PFY tension in this paper. By employing the Hamilton principle, the transverse dynamics differential equations of PFY are derived, which are discretized and solved by the Galerkin method and Runge–Kutta method, respectively. In the equations, the PFY between two adjacent rollers is simplified as an axially moving string to verify the generality of calculating natural frequencies. The calculated natural frequencies from the axially moving string model are compared with solved results from the transverse dynamics differential equations. It is shown that the approximation of natural frequencies can be obtained from the axially moving string model. This study attempts to establish an approximate generic model among the PFY tension, the spinning speed and the first natural frequency based on axially moving string model, from which the PFY tension can be calculated efficiently by employing the measured natural frequencies. The LDV method is used to measure the natural frequencies. A major advantage of the proposed method is to realize non-contact detection of PFY tension. The method is more useful under high-speed spinning conditions where contact tension detectors are not available. An experimental analysis is carried out to verify the effectiveness and accuracy of the proposed method. Therefore, it is believed that the non-contact detection of PFY tension in the spinning process by the LDV method is feasible.

2014 ◽  
Vol 709 ◽  
pp. 148-152
Author(s):  
Guo Qing Zhou ◽  
Ji Wang ◽  
Song Xiang

Sinusoidal shear deformation theory is presented to analyze the natural frequencies of simply supported laminated composite plates. The governing differential equations based on sinusoidal theory are solved by a Navier-type analytical method. The present results are compared with the available published results which verify the accuracy of sinusoidal theory.


1999 ◽  
Vol 121 (1) ◽  
pp. 105-110 ◽  
Author(s):  
Rong-Fong Fung ◽  
Chun-Chang Tseng

This paper presents the active vibration control of an axially moving string system through a mass-damper-spring (MDS) controller at its right-hand side (RHS) boundary. A nonlinear partial differential equation (PDE) describes a distributed parameter system (DPS) and directly selected as the object to be controlled. A new boundary control law is designed by sliding mode associated with Lyapunov method. It is shown that the boundary feedback states only include the displacement, velocity, and slope of the string at RHS boundary. Asymptotical stability of the control system is proved by the semigroup theory. Finally, finite difference scheme is used to validate the theoretical results.


2006 ◽  
Vol 129 (3) ◽  
pp. 380-385 ◽  
Author(s):  
Mohamed Gaith ◽  
Sinan Müftü

Transverse vibration of two axially moving beams connected by a Winkler elastic foundation is analyzed analytically. The two beams are tensioned, translating axially with a common constant velocity, simply supported at their ends, and of different materials and geometry. The natural frequencies and associated mode shapes are obtained. The natural frequencies of the system are composed of two infinite sets describing in-phase and out-of-phase vibrations. In case the beams are identical, these modes become synchronous and asynchronous, respectively. Divergence instability occurs at a critical velocity and a critical tension; and, divergence and flutter instabilities coexist at postcritical speeds, and divergence instability takes place precritical tensions. The effects of the mass, flexural rigidity, and axial tension ratios of the two beams are presented.


2019 ◽  
Vol 55 (1-2) ◽  
pp. 42-52
Author(s):  
Milad Ranjbaran ◽  
Rahman Seifi

This article proposes a new method for the analysis of free vibration of a cracked isotropic plate with various boundary conditions based on Kirchhoff’s theory. The isotropic plate is assumed to have a part-through surface or internal crack. The crack is considered parallel to one of the plate edges. Existence of the crack modified the governing differential equations which were formulated based on the line-spring model. Generalized differential quadrature method discretizes the obtained governing differential equations and converts them into an algebraic system of equations. Then, an eigenvalue analysis was used to determine the natural frequencies of the cracked plates. Some numerical results are given to demonstrate the accuracy and convergence of the obtained results. To demonstrate the efficiency of the method, the results were compared with finite element solutions and available literature. Also, effects of the crack depth, its location along the thickness, the length of the crack and different boundary conditions on the natural frequencies were investigated.


2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Chong Yang ◽  
Yu Fu ◽  
Jianmin Yuan ◽  
Min Guo ◽  
Keyu Yan ◽  
...  

The vibration-based damage identification method extracts the damage location and severity information from the change of modal properties, such as natural frequency and mode shape. Its performance and accuracy depends on the measurement precision. Laser Doppler vibrometer (LDV) provides a noncontact vibration measurement of high quality, but usually it can only do sampling on a single point. Scanning LDV is normally used to obtain the mode shape with a longer scanning time. In this paper, a damage detection technique is proposed using a self-synchronizing multipoint LDV. Multiple laser beams with various frequency shifts are projected on different points of the object, reflected and interfered with a common reference beam. The interference signal containing synchronized temporal vibration information of multiple spatial points is captured by a single photodetector and can be retrieved in a very short period. Experiments are conducted to measure the natural frequencies and mode shapes of pre- and postcrack cantilever beams. Mode shape curvature is calculated by numerical interpolation and windowed Fourier analysis. The results show that the artificial crack can be identified precisely from the change of natural frequencies and the difference of mode shape curvature squares.


Sign in / Sign up

Export Citation Format

Share Document