Book Reviews : Dynamic Mechanical Data of Non-Reinforced Plastics: K. Lundin Dept. of Technical Acoustics, Royal Institute of Technology, Stockholm, Sweden 1982, 137 pages

1984 ◽  
Vol 16 (8) ◽  
pp. 30-31
Author(s):  
V.R. Miller
Author(s):  
I. G. Anghel ◽  
H. Anglart ◽  
S. Hedberg ◽  
S. Rydstro¨m

This paper describes the experimental setup, instrumentation and procedures which have been developed in the thermal-hydraulic laboratory at the Royal Institute of Technology (KTH), Stockholm, Sweden, to perform new post-dryout heat transfer investigations in an annulus with flow obstacles. Previous investigations performed in the same laboratory indicated that flow obstacles had a considerable influence on the post-CHF heat transfer. The measured heat transfer enhancement was significantly under-predicted by existing models. However, the net effect of obstacles could not be deduced from the measurements, since reference - obstacle-free measurements - had not been performed. In addition, the number of thermocouples that could be installed inside the heated rod was limited to 8. These deficiencies have been removed in the current approach. Firstly, the present design of the test section allows for measurements both with and without flow obstacles. In this way the net effect of the obstacles will be captured. Secondly, a newly developed technique allowed the installation of 40 thermocouples inside of the heated rod. An additional 40 thermocouples have been installed on the external wall of the heated tube. Therefore, a significant improvement of the accuracy of measurements can be expected. The present arrangement of instrumentation is suitable to perform measurements of heat transfer under both steady-state and transient conditions.


1960 ◽  
Vol 33 (5) ◽  
pp. 1323-1374 ◽  
Author(s):  
C. L. Weidner ◽  
G. J. Crocker

Abstract An increasing number of papers in the field of adhesion have been appearing in Rubber Chemistry & Technology. In the period 1941–1950 twenty-two papers appeared in this Journal covering various aspects of adhesion, whereas in the year 1959 alone eleven papers appear. The Rubber Division Library at the University of Akron has compiled bibliographies as follows: Bibliography # 10, “Use of Synthetic Resins in Natural and Synthetic Rubbers”, covering the period 1930–1952; Bibliography # 18, “Rubber to Metal Bonding”, in two parts, one covering the period 1937–1954 and a supplement covering 1955–1958; and Bibliography #20, “Reclaim Rubber Cements”, covering the period 1927–1954. In addition, special bibliographies were prepared covering the period 1949–1958 on the subjects “Rubber to Wood Adhesives”, “Rubber to Fabric Adhesives”, “Bonding of Polyurethanes”, “Metal to Metal Adhesives”, and “Chemistry of Rubber Adhesives”. The most comprehensive text in the field is “Adhesion and Adhesives” edited by N. A. DeBruyne and R. Houwink. More limited in scope are “Adhesive Bonding of Metals” by Epstein, “Adhesives for Wood” by Knight, “Adhesive Bonding of Reinforced Plastics” by Perry. Also “Rubber to Metal Bonding” by Buchan, which stresses the brass plating technic. Skeist has recently edited a “Handbook of Adhesives”. The Encyclopedia of Chemical Technology contains articles on “Adhesives” in Volume I and the First Supplement Volume. Various symposia have been sources of worthwhile papers on adhesion. The Division of Paint, Plastics, and Printing Ink Chemistry, ACS, published such papers in their preprint booklets, volume XV, No. 1 (1955) and volume XX, No. 1 (1960). Papers given at this division's “Recent Advances in Adhesives” symposium in 1957 are also published. Publication of papers at two symposia held in 1952 (Society of The Chemical Industry, London; Case Institute of Technology, Cleveland) form a valuable collection. Papers from The Second International Congress of Surface Activity in London in 1957 are also published. Papers from a Symposium on Adhesion held by the Society of Rheology in 1959 are published in volume IV of the Society's Transactions. General review articles on adhesion with extensive bibliographies were published as follows : Rinker-Kline “Survey of Adhesives and Adhesion; Kline-Reinhart “Fundamentals of Adhesion”; Brantley-Charnell “Investigation of the Nature of Forces of Adhesion”; Reinhart-Callomon “Survey of Adhesion and Adhesives” and Rutzler “Types of Bonds Involved in Adhesion”. The Reinhart-Callomon survey is quite extensive in its bibliography.


2019 ◽  
Vol 11 (24) ◽  
pp. 7236 ◽  
Author(s):  
Anna-Karin Högfeldt ◽  
Anders Rosén ◽  
Christine Mwase ◽  
Ann Lantz ◽  
Lena Gumaelius ◽  
...  

The urgent need for actions in the light of the global challenges motivates international policy to define roadmaps for education on all levels to step forward and contribute with new knowledge and competencies. Challenge-Driven Education (CDE) is described as an education for Sustainable Development (ESD) approach, which aims to prepare students to work with global challenges and to bring value to society by direct impact. This paper describes, evaluates and discusses a three-year participatory implementation project of Challenge-driven education (CDE) within the engineering education at the University of Dar es Salam, UDSM, which has been carried out in collaboration with the Royal Institute of Technology, KTH in Stockholm. Conclusions are drawn on crucial aspects for engineering education change through the lens of Activity Theory (AT), where CDE is brought forward as a motivating ESD initiative for engineering faculty and students. Furthermore participatory co-creation is notably useful as it aims to embrace social values among the participants. Also, traditional organizational structures will need to be continuously negotiated in the light of the integration of more open-ended approaches in education.


Sign in / Sign up

Export Citation Format

Share Document