Weld zone characteristic and mechanical performance ofin situtitanium matrix composites using gas tungsten arc welding (GTAW)

In the present work, dissimilar butt joints between a low-Ni, medium-Mn austenitic stainless steel, M-Mn SS, and a Ni-Cr austenitic stainless steel, Ni-Cr SS, were processed by utilizing the gas tungsten arc welding (GTAW) technique at different heat inputs. A filler metal of ER308 was employed in the welding process. The filler yields 480 MPa, which is equivalent to the yield strength of M-Mn SS. The microstructural analysis and mechanical performance (i.e., tensile strength and hardness properties) of the concerned joints were studied by using an optical microscope and uniaxial tensile tests, respectively. The results revealed that a duplex structure from austenite matrix and delta ferrite is promoted in the fusion zone (FZ) of the dissimilar joints processed with low and high energy inputs (0.486 kJ/mm and 0.558 kJ/mm). The FZ of the specimens welded at high heat input exhibited the lowest hardness value (151.2 HV) in comparison to heat affected zone (HAZ) (166.3 HV). Moreover, the joints exhibited a low tensile strength of 610 MPa. The achieved strength is significantly lower than the strengths of the base metals (BMs) M-Mn SS and Ni-Cr SS. This is mainly attributed to the inhomogeneous dendritic structure of the FZ with Cr-carbides precipitation.

Download Full-text

Friction Stir Welding of 2205 Duplex Stainless Steel: Feasibility of Butt Joint Groove Filling in Comparison to Gas Tungsten Arc Welding

Materials ◽

10.3390/ma14164597 ◽

2021 ◽

Vol 14 (16) ◽

pp. 4597

Author(s):

Mohamed M. Z. Ahmed ◽

Khaled A. Abdelazem ◽

Mohamed M. El-Sayed Seleman ◽

Bandar Alzahrani ◽

Kamel Touileb ◽

...

Keyword(s):

Stainless Steel ◽

Friction Stir Welding ◽

Duplex Stainless Steel ◽

Arc Welding ◽

Weld Zone ◽

Gas Tungsten Arc Welding ◽

Grain Refining ◽

Friction Stir ◽

Gas Tungsten Arc ◽

Gas Tungsten

This work investigates the feasibility of using friction stir welding (FSW) process as a groove filling welding technique to weld duplex stainless steel (DSS) that is extensively used by petroleum service companies and marine industries. For the FSW experiments, three different groove geometries without root gap were designed and machined in a DSS plates 6.5 mm thick. FSW were carried out to produce butt-joints at a constant tool rotation rate of 300 rpm, traverse welding speed of 25 mm/min, and tilt angle of 3o using tungsten carbide (WC) tool. For comparison, the same DSS plates were welded using gas tungsten arc welding (GTAW). The produced joints were evaluated and characterized using radiographic inspection, optical microscopy, and hardness and tensile testing. Electron back scattering diffraction (EBSD) was used to examine the grain structure and phases before and after FSW. The initial results indicate that FSW were used successfully to weld DSS joints with different groove designs with defect-free joints produced using the 60° V-shape groove with a 2 mm root face without root gap. This friction stir welded (FSWed) joint was further investigated and compared with the GTAW joint. The FSWed joint microstructure mainly consists of α and γ with significant grain refining; the GTWA weld contains different austenitic-phase (γ) morphologies such as grain boundary austenite (GBA), intragranular austenite precipitates (IGA), and Widmanstätten austenite (WA) besides the ferrite phase (α) in the weld zone (WZ) due to the used high heat input and 2209 filler rod. The yield strength, ultimate tensile strength, and elongation of the FSWed joint are enhanced over the GTAW weldment by 21%, 41%, and 66% and over the BM by 65%, 33%, and 54%, respectively. EBSD investigation showed a significant grain refining after FSW with grain size average of 1.88 µm for austenite and 2.2 µm for ferrite.

Download Full-text

Arc Characteristics and Weld Bead Microstructure of Ti-6Al-4V Titanium Alloy in Ultra-high Frequency Pulse Gas Tungsten Arc Welding (UHFP-GTAW) Process

Materials Science ◽

10.5755/j01.ms.26.4.22329 ◽

2020 ◽

Vol 26 (4) ◽

pp. 426-431

Author(s):

Wei LI ◽

Gaochong LV ◽

Qiang WANG ◽

Songtao HUANG

Keyword(s):

Titanium Alloy ◽

Fusion Zone ◽

Arc Welding ◽

Gas Tungsten Arc Welding ◽

Weld Bead ◽

Gas Tungsten Arc ◽

Arc Characteristics ◽

Arc Pressure ◽

Gtaw Process ◽

Gas Tungsten

To resolve the problem of grain coarsening occurring in the fusion zone and the heat-affected zone during conventional gas tungsten arc welding(C-GTAW) welded titanium alloy, which severely restricts the improvement of weld mechanical properties, welding experiments on Ti-6Al-4V titanium alloy by adopting ultra-high frequency pulse gas tungsten arc welding (UHFP-GTAW) technique were carried out to study arc characteristics and weld bead microstructure. Combined with image processing technique, arc shapes during welding process were observed by high-speed camera. Meanwhile the average arc pressure under various welding parameters were obtained by adopting pressure measuring equipment with high-precision. In addition, the metallographic samples of the weld cross section were prepared for observing weld bead geometry and microstructure of the fusion zone. The experimental results show that, compared with C-GTAW, UHFP-GTAW process provides larger arc energy density and higher proportion of arc core region to the whole arc area. Moreover, UHFP-GTAW process has the obviously effect on grain refinement, which can decrease the grain size of the fusion zone. The results also revealed that a significant increase of arc pressure while increasing pulse frequency of UHFP-GTAW, which could improve the depth-to-width ratio of weld beads.

Download Full-text