Carbothermic reduction of ilmenite and rutile as means of production of iron based Ti(O,C) metal matrix composites

1991 ◽  
Vol 7 (9) ◽  
pp. 842-848 ◽  
Author(s):  
B. S. Terry ◽  
O. Chinyamakobvu
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Carbothermic Reduction ◽  
Matrix Composites ◽  
Iron Based ◽  
Means Of Production

scholarly journals On the Microstructure, Strength, Fracture, and Tribological Properties of Iron-Based MMCs with Addition of Mixed Carbide Nanoparticulates

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2892 ◽  
Author(s):  
Grzegorz Królczyk ◽  
Eugene Feldshtein ◽  
Larisa Dyachkova ◽  
Mariusz Michalski ◽  
Tomasz Baranowski ◽  
...  
Keyword(s):  
Metal Matrix Composites ◽  
Tribological Properties ◽  
Metal Matrix ◽  
Design Method ◽  
Matrix Composites ◽  
Wear Process ◽  
Lattice Design ◽  
Friction Temperature ◽  
Iron Based ◽  
Fracture Features

In this paper, the features of the strength, fractures, and tribological behavior of metal-matrix composites based on the FeGr1 material are discussed. To improve the material properties, a mixture of SiC, Al2O3 and C nanoparticulates have been added to an iron-based matrix. The simplex lattice design method and hardness, compression, and bending tests were used to determine the mechanical properties. Scanning electron microscopy was applied for fracture features analysis. Different fracture types, mainly trans-crystalline quasi-brittle and brittle fracture or inter-granular fracture and microcracks were registered for the composites tested. Depending on the type and amount of ceramic additives, significant changes in strength, as well as in the fracture features of the metal-matrix composites (MMCs), were observed. Based on tribological tests, changes in the momentary coefficients of friction, temperature of the friction surface, and wear rate of the composites with nanoparticulates were described. An analysis of the worn surface morphology revealed changes in the wear process depending on the MMC composition. It was shown that the use of hybrid mixed additives based on hard ceramic nanoparticulates improved both strength and tribological properties of composites.

Self-Lubricating Iron-Based Metal Matrix Composites

2021 ◽  
pp. 41-51
Author(s):  
Shuhaib Mushtaq ◽  
M.F. Wani ◽  
Carsten Gachot ◽  
Mohd Nadeem Bhat
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Matrix Composites ◽  
Iron Based

Physico-Mechanical Properties of Sintered Iron-Silica Sand Nanoparticle Composites: A Preliminary Study

2012 ◽  
Vol 332 ◽  
pp. 7-16 ◽  
Author(s):  
Tahir Ahmad ◽  
Othman Mamat ◽  
Rafiq Ahmad
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Sintering Temperature ◽  
Milling Process ◽  
Silica Sand ◽  
Matrix Composites ◽  
Sintered Iron ◽  
Preliminary Study ◽  
Iron Based ◽  
Nanoparticle Composites

The present study aims to develop silica sand nanoparticles using the ball-milling process and to utilize these nanoparticles as reinforcement for iron-based metal matrix composites. Iron-based metal-matrix composites with 5, 10, 15 and 20wt.% of the processed silica sand nanoparticles were developed using powder metallurgy technique and sintered at 900°C, 1000°C and 1100°C. The results showed that the addition of silica sand nanoparticles to iron as reinforcement decreased the green density, albeit with an improvement in sintered densities. It was also observed that the increase in the sintering temperature results in an improvement of microstructure and microhardness of the composites. The maximum hardness of 168HV in iron-based composites was found with the addition of 20wt.% of silica sand nanoparticles at a 1100°C sintering temperature. It is proposed that the mechanism for the occurrence of this observed increment in microhardness is due to diffusion of silica sand nanoparticles into porous sites of the composites, resulting in the formation of FeSi phase.

Sign in / Sign up

Export Citation Format

Share Document