Near-surface full-waveform inversion in a transmission surface-consistent scheme

Geophysics ◽  
2020 ◽  
pp. 1-57
Author(s):  
Daniele Colombo ◽  
Ernesto Sandoval ◽  
Diego Rovetta ◽  
Apostolos Kontakis
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Waveform Inversion ◽  
Surface Velocity ◽  
Full Waveform Inversion ◽  
Velocity Mapping ◽  
Signal To Noise ◽  
Near Surface ◽  
Velocity Modeling ◽  
Full Waveform

Land seismic velocity modeling is a difficult task largely related to the description of the near surface complexities. Full waveform inversion is the method of choice for achieving high-resolution velocity mapping but its application to land seismic data faces difficulties related to complex physics, unknown and spatially varying source signatures, and low signal-to-noise ratio in the data. Large parameter variations occur in the near surface at various scales causing severe kinematic and dynamic distortions of the recorded wavefield. Some of the parameters can be incorporated in the inversion model while others, due to sub-resolution dimensions or unmodeled physics, need to be corrected through data preconditioning; a topic not well described for land data full waveform inversion applications. We have developed novel algorithms and workflows for surface-consistent data preconditioning utilizing the transmitted portion of the wavefield, signal-to-noise enhancement by generation of CMP-based virtual super shot gathers, and robust 1.5D Laplace-Fourier full waveform inversion. Our surface-consistent scheme solves residual kinematic corrections and amplitude anomalies via scalar compensation or deconvolution of the near surface response. Signal-to-noise enhancement is obtained through the statistical evaluation of volumetric prestack responses at the CMP position, or virtual super (shot) gathers. These are inverted via a novel 1.5D acoustic Laplace-Fourier full waveform inversion scheme using the Helmholtz wave equation and Hankel domain forward modeling. Inversion is performed with nonlinear conjugate gradients. The method is applied to a complex structure-controlled wadi area exhibiting faults, dissolution, collapse, and subsidence where the high resolution FWI velocity modeling helps clarifying the geological interpretation. The developed algorithms and automated workflows provide an effective solution for massive full waveform inversion of land seismic data that can be embedded in typical near surface velocity analysis procedures.

High-resolution Radon preconditioning for full-waveform inversion of land seismic data

2017 ◽  
Vol 5 (4) ◽  
pp. SR23-SR33 ◽  
Author(s):  
Xin Cheng ◽  
Kun Jiao ◽  
Dong Sun ◽  
Zhen Xu ◽  
Denes Vigh ◽  
...  
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Waveform Inversion ◽  
Low Frequency ◽  
Velocity Fields ◽  
Surface Velocity ◽  
Surface Model ◽  
Full Waveform Inversion ◽  
Near Surface ◽  
Full Waveform

Over the past decade, acoustic full-waveform inversion (FWI) has become one of the standard methods in the industry to construct high-resolution velocity fields from the seismic data acquired. While most of the successful applications are for marine acquisition data with rich low-frequency diving or postcritical waves at large offsets, the application of acoustic FWI on land data remains a challenging topic. Land acoustic FWI application faces many severe difficulties, such as the presence of strong elastic effects, large near-surface velocity contrast, and heterogeneous, topography variations, etc. In addition, it is well-known that low-frequency transmitted seismic energy is crucial for the success of FWI to overcome sensitivity to starting velocity fields; unfortunately, those are the parts of the data that suffer the most from a low signal-to-noise ratio (S/N) in land acquisition. We have developed an acoustic FWI application on a land data set from North Kuwait, and demonstrated our solutions to mitigate some of the challenges posed by land data. More specifically, we have developed a semblance-based high-resolution Radon (HR-Radon) inversion approach to enhance the S/N of the low-frequency part of the FWI input data and to ultimately improve the convergence of the land FWI workflow. To mitigate the impact of elastic effects, we included only the diving and postcritical early arrivals in the waveform inversion. Our results show that, with the aid of HR-Radon preconditioning and a carefully designed workflow, acoustic FWI has the ability to derive a reliable high-resolution near-surface model that could not be otherwise recovered through traditional tomographic methods.

Full waveform inversion: early start of model building process to resolve the complex near surface model in the Exmouth sub-basin, North West Shelf Australia

2018 ◽  
Vol 58 (2) ◽  
pp. 884
Author(s):  
Lianping Zhang ◽  
Haryo Trihutomo ◽  
Yuelian Gong ◽  
Bee Jik Lim ◽  
Alexander Karvelas
Keyword(s):  
Model Building ◽  
Waveform Inversion ◽  
Velocity Model ◽  
Surface Velocity ◽  
Image Point ◽  
Surface Model ◽  
Full Waveform Inversion ◽  
Near Surface ◽  
North West ◽  
Full Waveform

The Schlumberger Multiclient Exmouth 3D survey was acquired over the Exmouth sub-basin, North West Shelf Australia and covers 12 600 km2. One of the primary objectives of this survey was to produce a wide coverage of high quality imaging with advanced processing technology within an agreed turnaround time. The complexity of the overburden was one of the imaging challenges that impacted the structuration and image quality at the reservoir level. Unlike traditional full-waveform inversion (FWI) workflow, here, FWI was introduced early in the workflow in parallel with acquisition and preprocessing to produce a reliable near surface velocity model from a smooth starting model. FWI derived an accurate and detailed near surface model, which subsequently benefitted the common image point (CIP) tomography model updates through to the deeper intervals. The objective was to complete the FWI model update for the overburden concurrently with the demultiple stages hence reflection time CIP tomography could start with a reasonably good velocity model upon completion of the demultiple process.

scholarly journals From surface seismic data to reservoir elastic parameters using a full-wavefield redatuming approach

2019 ◽  
Vol 221 (1) ◽  
pp. 115-128 ◽  
Author(s):  
Aayush Garg ◽  
D J Verschuur
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Waveform Inversion ◽  
Full Waveform Inversion ◽  
Impulse Responses ◽  
Target Domain ◽  
Elastic Parameters ◽  
Full Waveform ◽  
Parameters Inversion ◽  
Local Input

SUMMARY Traditionally, reservoir elastic parameters inversion suffers from the overburden multiple scattering and transmission imprint in the local input data used for the target-oriented inversion. In this paper, we present a full-wavefield approach, called reservoir-oriented joint migration inversion (JMI-res), to estimate the high-resolution reservoir elastic parameters from surface seismic data. As a first step in JMI-res, we reconstruct the fully redatumed data (local impulse responses) at a suitable depth above the reservoir from the surface seismic data, while correctly accounting for the overburden interal multiples and transmission losses. Next, we apply a localized elastic full waveform inversion on the estimated impulse responses to get the elastic parameters. We show that JMI-res thus provides much more reliable local target impulse responses, thus yielding high-resolution elastic parameters, compared to a standard redatuming procedure based on time reversal of data. Moreover, by using this kind of approach we avoid the need to apply a full elastic full waveform inversion-type process for the whole subsurface, as within JMI-res elastic full waveform inversion is only restricted to the reservoir target domain.

scholarly journals Full Waveform Inversion in generalized coordinates for zones of curved topography

2018 ◽  
Vol 8 (2) ◽  
Author(s):  
César Augusto Arias- Chica ◽  
David Abreo ◽  
Sergio Abreo ◽  
Luis Fernando Duque- Gómez ◽  
Ana Beatríz Ramírez- Silva
Keyword(s):  
Computing Time ◽  
Waveform Inversion ◽  
Surface Velocity ◽  
Full Waveform Inversion ◽  
Near Surface ◽  
Velocity Models ◽  
Full Waveform ◽  
Wide Range ◽  
Rugged Topography ◽  
Uniform Rectangular Grid

Full waveform inversion (FWI) has been recently used to estimate subsurface parameters, such as velocity models. This method, however, has a number of drawbacks when applied to zones with rugged topography due to the forced application of a Cartesian mesh on a curved surface. In this work, we present a simple coordinate transformation that enables the construction of a curved mesh. The proposed transformation is more suitable for rugged surfaces and it allows mapping a physical curved domain into a uniform rectangular grid, where acoustic FWI can be applied in the traditional way by introducing a modified Laplacian. We prove that the proposed approximation can have a wide range of applications, producing precise near-surface velocity models without increasing the computing time of the FWI.

scholarly journals Ground topography effects on near-surface elastic full waveform inversion

2016 ◽  
Vol 207 (1) ◽  
pp. 67-71 ◽  
Author(s):  
André Nuber ◽  
Edgar Manukyan ◽  
Hansruedi Maurer
Keyword(s):  
Surface Topography ◽  
Seismic Data ◽  
Waveform Inversion ◽  
Ground Surface ◽  
Full Waveform Inversion ◽  
Near Surface ◽  
Long Wavelength ◽  
Full Waveform ◽  
Amplitude Fluctuations ◽  
Image Artefacts

Abstract The effects of neglecting ground surface topography variations in elastic full waveform inversion are investigated using two classes of synthetic example. The models include various high-contrast velocity and density anomalies, as they are often observed in near-surface applications. The first type of example shows that failing to account for even small amplitude fluctuations in topography introduces velocity artefacts in the near-surface part of the tomogram as well as degrades significantly the spatial resolution of features at greater depths. The disturbances are particularly severe when the topographic fluctuations have wavelengths comparable to the minimum seismic wavelength. The second type of synthetic example considers long wavelength topography variations of various amplitudes. It is found that neglecting topography with an amplitude fluctuation greater than half the minimum seismic wavelength leads to appreciable inversion image artefacts. Therefore, the incorporation of surface topography, even if it appears minor, is essential for successful elastic full waveform inversion of land seismic data.

Sign in / Sign up

Export Citation Format

Share Document