Geometry Optimization of a Piezoelectric Microcantilever Energy Harvester

2020 ◽  
pp. 97-117
Author(s):  
Khalil Khanafer ◽  
Ali Al-Masri ◽  
Kambiz Vafai
Keyword(s):  
Energy Harvester ◽  
Geometry Optimization ◽  
Piezoelectric Microcantilever

Design Optimization of Low Power and Low Frequency Vibration Based MEMS Energy Harvester

2013 ◽  
Vol 475-476 ◽  
pp. 1624-1628
Author(s):  
Hasnizah Aris ◽  
David Fitrio ◽  
Jack Singh
Keyword(s):  
Low Power ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Geometry Optimization ◽  
Low Frequency ◽  
Substrate Thickness ◽  
Power Harvesting ◽  
Low Frequency Vibration ◽  
Length Width ◽  
Development And Utilization

The development and utilization of different structural materials, optimization of the cantilever geometry and power harvesting circuit are the most commonly methods used to increase the power density of MEMS energy harvester. This paper discusses the cantilever geometry optimization process of low power and low frequency of bimorph MEMS energy harvester. Three piezoelectric materials, ZnO, AlN and PZT are deposited on top and bottom of the cantilever Si substrate. This study focuses on the optimization of the cantilevers length, width, substrate thickness and PZe thickness in order to achieve lower than 600 Hz of resonant frequency. The harvested power for this work is in the range of 0.02 ~ 194.49 nW.

Simply supported FPEDs connected by springs for broadband energy harvesting

2020 ◽  
Vol 64 (1-4) ◽  
pp. 201-210
Author(s):  
Yoshikazu Tanaka ◽  
Satoru Odake ◽  
Jun Miyake ◽  
Hidemi Mutsuda ◽  
Atanas A. Popov ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Evaluation Method ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Functional Materials ◽  
Vibration Energy ◽  
Theoretical Evaluation ◽  
Vibration Energy Harvester ◽  
Polyvinylidene Difluoride ◽  
Simply Supported

Energy harvesting methods that use functional materials have attracted interest because they can take advantage of an abundant but underutilized energy source. Most vibration energy harvester designs operate most effectively around their resonant frequency. However, in practice, the frequency band for ambient vibrational energy is typically broad. The development of technologies for broadband energy harvesting is therefore desirable. The authors previously proposed an energy harvester, called a flexible piezoelectric device (FPED), that consists of a piezoelectric film (polyvinylidene difluoride) and a soft material, such as silicon rubber or polyethylene terephthalate. The authors also proposed a system based on FPEDs for broadband energy harvesting. The system consisted of cantilevered FPEDs, with each FPED connected via a spring. Simply supported FPEDs also have potential for broadband energy harvesting, and here, a theoretical evaluation method is proposed for such a system. Experiments are conducted to validate the derived model.

Vibration based Energy Harvester Employing ZnO Film on the Stainless Steel Substrate

2013 ◽  
Vol 133 (4) ◽  
pp. 126-127 ◽  
Author(s):  
Shota Hosokawa ◽  
Motoaki Hara ◽  
Hiroyuki Oguchi ◽  
Hiroki Kuwano
Keyword(s):  
Stainless Steel ◽  
Energy Harvester ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Zno Film

Hybrid Vibration Energy Harvester based on Stochastic Resonance

2018 ◽  
Vol 138 (5) ◽  
pp. 185-190
Author(s):  
Meng Su ◽  
Dai Kobayashi ◽  
Nobuyuki Takama ◽  
Beomjoon Kim
Keyword(s):  
Stochastic Resonance ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Vibration Energy Harvester

Improvement of Power Generation in Low Acceleration for Electrostatic Energy Harvester by Using Bipolar Charging Method

2015 ◽  
Vol 135 (9) ◽  
pp. 372-373 ◽  
Author(s):  
Koji Sonoda ◽  
Keidai Minami ◽  
Naoki Miwatani ◽  
Kensuke Kanda ◽  
Takayuki Fujita ◽  
...  
Keyword(s):  
Power Generation ◽  
Energy Harvester ◽  
Electrostatic Energy

A Fluidic Vibrational Energy Harvester for Implantable Medical Device Applications

2017 ◽  
Vol 137 (6) ◽  
pp. 152-158
Author(s):  
Satoshi Inoue ◽  
Takuya Takahashi ◽  
Momoko Kumemura ◽  
Kazunori Ishibashi ◽  
Hiroyuki Fujita ◽  
...  
Keyword(s):  
Medical Device ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Implantable Medical Device ◽  
Device Applications

GEOMETRY OPTIMIZATION OF AIR-ASSISTED SWIRL NOZZLE BASED ON SURROGATE MODELS AND COMPUTATIONAL FLUID DYNAMICS

2019 ◽  
Vol 29 (7) ◽  
pp. 605-628
Author(s):  
Zongli Yi ◽  
Li Hou ◽  
Qi Zhang ◽  
Yousheng Wang ◽  
Yunxia You
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Geometry Optimization ◽  
Surrogate Models

CLB18: A New Structural Database with Unusual Carbon–Carbon Long Bonds

2020 ◽  
Author(s):  
Pierpaolo Morgante ◽  
Roberto Peverati
Keyword(s):  
Transition Metal Complexes ◽  
Low Cost ◽  
Geometry Optimization ◽  
Structure Calculation ◽  
Unique Property ◽  
Spin States ◽  
Calculation Methods ◽  
Large Molecules ◽  
Barrier Heights ◽  
Structural Database

<div><div><div><p>In this Letter, we introduce a new database called carbon long bond 18 (CLB18), composed of 18 structures with one long C–C bond. We use this new database to evaluate the performance of several low-cost methods commonly used for geometry optimization of medium and large molecules. We found that the long bonds in CLB18 are electronically different from those found in barrier heights databases. We also report the unexpected correlation between the results of CLB18 and those of the energetics of spin states in transition-metal complexes. Given this unique property, CLB18 can be a useful tool for assessing existing electronic structure calculation methods and developing new ones.</p></div></div></div>

Sign in / Sign up

Export Citation Format

Share Document