Large eddy simulation of natural cavitating flows in Venturi-type sections

2010 ◽  
Vol 225 (2) ◽  
pp. 369-381 ◽  
Author(s):  
N M Nouri ◽  
S M H Mirsaeedi ◽  
M Moghimi
Keyword(s):  
Large Eddy Simulation ◽  
Preliminary Data ◽  
Cavitating Flow ◽  
Navier Stokes ◽  
Computational Time ◽  
Time Averaging ◽  
Cavitating Flows ◽  
Eddy Simulation ◽  
Wide Range ◽  
Large Eddy

Large eddy simulation (LES) is used here to model the cavitating flow at a Venturi-type section. Cavitating flows can occur in a wide range of applications. The flow is represented here by means of LES, which compared to Reynolds-averaged Navier—Stokes (RANS) has the advantage that in it the large, energy-containing structures are resolved directly, whereas most of these structures are modelled in RANS. This gives LES an improved fidelity over RANS, although, due to the time averaging, the required computational time is considerably lower for RANS than for LES. The conclusion of this work shows that the qualitative comparisons with earlier preliminary data and the simulated general cavitation behaviour correlate reasonably well with experimental observations and that the simulations have the ability to predict cavitation cycle in more detail.

Large eddy simulation applications in gas turbines

2009 ◽  
Vol 367 (1899) ◽  
pp. 2827-2838 ◽  
Author(s):  
Kevin Menzies
Keyword(s):  
Large Eddy Simulation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Complex Geometry ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Wide Range ◽  
Large Eddy ◽  
Design Cycle ◽  
Flow Phenomena

The gas turbine presents significant challenges to any computational fluid dynamics techniques. The combination of a wide range of flow phenomena with complex geometry is difficult to model in the context of Reynolds-averaged Navier–Stokes (RANS) solvers. We review the potential for large eddy simulation (LES) in modelling the flow in the different components of the gas turbine during a practical engineering design cycle. We show that while LES has demonstrated considerable promise for reliable prediction of many flows in the engine that are difficult for RANS it is not a panacea and considerable application challenges remain. However, for many flows, especially those dominated by shear layer mixing such as in combustion chambers and exhausts, LES has demonstrated a clear superiority over RANS for moderately complex geometries although at significantly higher cost which will remain an issue in making the calculations relevant within the design cycle.

On LES Methods Applied to Seal Geometries

2012 ◽  
Author(s):  
James Tyacke ◽  
Richard Jefferson-Loveday ◽  
Paul Tucker
Keyword(s):  
Maximum Error ◽  
Labyrinth Seal ◽  
Navier Stokes ◽  
Final Solution ◽  
Complex Flow ◽  
Eddy Simulation ◽  
Wide Range ◽  
Large Eddy ◽  
Rans Models ◽  
Flow Through

Nine Large Eddy Simulation (LES) methods are used to simulate flow through two labyrinth seal geometries and are compared with a wide range of Reynolds-Averaged Navier-Stokes (RANS) solutions. These involve one-equation, two-equation and Reynolds Stress RANS models. Also applied are linear and nonlinear pure LES models, hybrid RANS-Numerical-LES (RANS-NLES) and Numerical-LES (NLES). RANS is found to have a maximum error and a scatter of 20%. A similar level of scatter is also found among the same turbulence model implemented in different codes. In a design context, this makes RANS unusable as a final solution. Results show that LES and RANS-NLES is capable of accurately predicting flow behaviour of two seals with a scatter of less than 5%. The complex flow physics gives rise to both laminar and turbulent zones making most LES models inappropriate. Nonetheless, this is found to have minimal tangible results impact. In accord with experimental observations, the ability of LES to find multiple solutions due to solution non-uniqueness is also observed.

Hybrid Large Eddy Simulation/Reynolds-Averaged Navier–Stokes Analysis of a Premixed Ethylene-Fueled Dual-Mode Scramjet Combustor

AIAA Journal ◽  
2021 ◽  
pp. 1-17
Author(s):  
Tanner B. Nielsen ◽  
Jack R. Edwards ◽  
Harsha K. Chelliah ◽  
Damien Lieber ◽  
Clayton Geipel ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Navier Stokes ◽  
Dual Mode ◽  
Eddy Simulation ◽  
Scramjet Combustor ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes

Simulation of Vortex Instability in a Pipe Trifurcation

2003 ◽  
Author(s):  
Albert Ruprecht ◽  
Ralf Neubauer ◽  
Thomas Helmrich
Keyword(s):  
Large Eddy Simulation ◽  
Turbulence Model ◽  
Model Test ◽  
Reasonable Agreement ◽  
Navier Stokes ◽  
Extended Version ◽  
Vortex Instability ◽  
Flow Phenomenon ◽  
Eddy Simulation ◽  
Large Eddy

The vortex instability in a spherical pipe trifurcation is investigated by applying a Very Large Eddy Simulation (VLES). For this approach an new adaptive turbulence model based on an extended version of the k-ε model is used. Applying a classical Reynolds-averaged Navier-Stokes-Simulation with the standard k-ε model is not able to forecast the vortex instability. However the prescribed VLES method is capable to predict this flow phenomenon. The obtained results show a reasonable agreement with measurements in a model test.

Large Eddy Simulation of Cross Flow in Pipe Junction

2018 ◽  
Author(s):  
Jiajun Chen ◽  
Yue Sun ◽  
Hang Zhang ◽  
Dakui Feng ◽  
Zhiguo Zhang
Keyword(s):  
Large Eddy Simulation ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Exciting Force ◽  
Navier Stokes ◽  
Pipe Network ◽  
Eddy Simulation ◽  
Large Eddy

Mixing in pipe junctions can play an important role in exciting force and distribution of flow in pipe network. This paper investigated the cross pipe junction and proposed an improved plan, Y-shaped pipe junction. The numerical study of a three-dimensional pipe junction was performed for calculation and improved understanding of flow feature in pipe. The filtered Navier–Stokes equations were used to perform the large-eddy simulation of the unsteady incompressible flow in pipe. From the analysis of these results, it clearly appears that the vortex strength and velocity non-uniformity of centerline, can be reduced by Y-shaped junction. The Y-shaped junction not only has better flow characteristic, but also reduces head loss and exciting force. The results of the three-dimensional improvement analysis of junction can be used in the design of pipe network for industry.

Large Eddy Simulation of the Flow Around a Diffuser-Equipped Bluff Body in Ground Effect

2011 ◽  
Author(s):  
Lara Schembri Puglisevich ◽  
Gary Page
Keyword(s):  
Large Eddy Simulation ◽  
Bluff Body ◽  
Vortex Formation ◽  
Ground Effect ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Flow Structures ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Features

Unsteady Large Eddy Simulation (LES) is carried out for the flow around a bluff body equipped with an underbody rear diffuser in close proximity to the ground, representing an automotive diffuser. The goal is to demonstrate the ability of LES to model underbody vortical flow features at experimental Reynolds numbers (1.01 × 106 based on model height and incoming velocity). The scope of the time-dependent simulations is not to improve on Reynolds-Averaged Navier Stokes (RANS), but to give further insight into vortex formation and progression, allowing better understanding of the flow, hence allowing more control. Vortical flow structures in the diffuser region, along the sides and top surface of the bluff body are successfully modelled. Differences between instantaneous and time-averaged flow structures are presented and explained. Comparisons to pressure measurements from wind tunnel experiments on an identical bluff body model shows a good level of agreement.

Sign in / Sign up

Export Citation Format

Share Document