Estimation of the air entrainment characteristics of a transient high-pressure diesel spray

2005 ◽  
Vol 219 (8) ◽  
pp. 1025-1036 ◽  
Author(s):  
W Choi ◽  
B-C Choi
Keyword(s):  
High Pressure ◽  
Particle Image Velocimetry ◽  
Particle Image ◽  
Air Entrainment ◽  
Diesel Spray ◽  
Entrainment Rate ◽  
Recirculating Flow ◽  
Air Entrainment Rate ◽  
Image Velocimetry ◽  
Ambient Gas

The air entrainment characteristics of a transient high-pressure diesel spray were investigated with respect to time and location for injection pressures ( Pinj = 76 or 137 MPa) and ambient density (ρa = 15.6 kg/m3) under the non-evaporating condition (303 K). A particle image velocimetry analysis was introduced and some parameters were defined to express air entrainment characteristics. The air entrainment rate increased greatly as the flow moved downstream owing to a larger contact surface area and a recirculating flow. Higher pressure led to a greater entrainment rate with higher effectiveness. The speed (spray tip and front ambient gas) and volume (spray and laterally entrained gas) relations suggested the possibility for the renewal against the lateral-dominant entrainment mechanism.

Particle Image Velocimetry in a High-Pressure Turbine Stage at Aerodynamically Engine Representative Conditions

2020 ◽  
Author(s):  
Daniel Inman ◽  
David Gonzalez Cuadrado ◽  
Valeria Andreoli ◽  
Jordan Fisher ◽  
Guillermo Paniagua ◽  
...  
Keyword(s):  
High Pressure ◽  
Particle Image Velocimetry ◽  
Vector Fields ◽  
Particle Image ◽  
Flow Direction ◽  
Operating Conditions ◽  
Velocity Magnitude ◽  
Resultant Velocity ◽  
Image Velocimetry ◽  
Annular Cascade

Abstract Particle Image Velocimetry (PIV) is a well-established technique for determining the flow direction and velocity magnitude of complex flows. This paper presents a methodology for executing this non-intrusive measurement technique to study a scaled-up turbine vane geometry within an annular cascade at engine-relevant conditions. Custom optical tools such as laser delivery probes and imaging inserts were manufactured to mitigate the difficult optical access of the test section and perform planar PIV. With the use of a burst-mode Nd: YAG laser and Photron FASTCAM camera, the frame straddling technique is implemented to enable short time intervals for the collection of image pairs and velocity fields at 10 kHz. Furthermore, custom image processing tools were developed to optimize the contrast and intensity balance of each image pair to maximize particle number and uniformity, while removing scattering and background noise. The pre-processing strategies significantly improve the vector yield under challenging alignment, seeding, and illumination conditions. With the optical and software tools developed, planar PIV was conducted in the passage of a high-pressure stator row, at mid-span, in an annular cascade. Different Mach and Reynolds number operating conditions were achieved by modifying the temperature and mass flow. With careful spatial calibration, the resultant velocity vector fields are compared with Reynolds Averaged Navier Stokes (RANS) simulations of the vane passage with the same geometry and flow conditions. Uncertainty analysis of the experimental results is also presented and discussed, along with prospects for further improvements.

Stereoscopic Particle Image Velocimetry Analysis of Healthy and Emphysemic Alveolar Sac Models

2011 ◽  
Vol 133 (6) ◽  
Author(s):  
Emily J. Berg ◽  
Risa J. Robinson
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Fluid Motion ◽  
Three Dimensional ◽  
Flow Fields ◽  
Stereoscopic Particle Image Velocimetry ◽  
Recirculating Flow ◽  
Image Velocimetry ◽  
Flow Speeds ◽  
Healthy Lung

Emphysema is a progressive lung disease that involves permanent destruction of the alveolar walls. Fluid mechanics in the pulmonary region and how they are altered with the presence of emphysema are not well understood. Much of our understanding of the flow fields occurring in the healthy pulmonary region is based on idealized geometries, and little attention has been paid to emphysemic geometries. The goal of this research was to utilize actual replica lung geometries to gain a better understanding of the mechanisms that govern fluid motion and particle transport in the most distal regions of the lung and to compare the differences that exist between healthy and emphysematous lungs. Excised human healthy and emphysemic lungs were cast, scanned, graphically reconstructed, and used to fabricate clear, hollow, compliant models. Three dimensional flow fields were obtained experimentally using stereoscopic particle image velocimetry techniques for healthy and emphysematic breathing conditions. Measured alveolar velocities ranged over two orders of magnitude from the duct entrance to the wall in both models. Recirculating flow was not found in either the healthy or the emphysematic model, while the average flow rate was three times larger in emphysema as compared to healthy. Diffusion dominated particle flow, which is characteristic in the pulmonary region of the healthy lung, was not seen for emphysema, except for very small particle sizes. Flow speeds dissipated quickly in the healthy lung (60% reduction in 0.25 mm) but not in the emphysematic lung (only 8% reduction 0.25 mm). Alveolar ventilation per unit volume was 30% smaller in emphysema compared to healthy. Destruction of the alveolar walls in emphysema leads to significant differences in flow fields between the healthy and emphysemic lung. Models based on replica geometry provide a useful means to quantify these differences and could ultimately improve our understanding of disease progression.

scholarly journals Analysis of the interaction of Spray G and in-cylinder flow in two optical engines for late gasoline direct injection

2019 ◽  
Vol 21 (1) ◽  
pp. 169-184 ◽  
Author(s):  
Christopher Geschwindner ◽  
Patrick Kranz ◽  
Cooper Welch ◽  
Marius Schmidt ◽  
Benjamin Böhm ◽  
...  
Keyword(s):  
Particle Image Velocimetry ◽  
Flow Field ◽  
Particle Image ◽  
Direct Injection ◽  
Standard Condition ◽  
Air Entrainment ◽  
Geometrical Parameters ◽  
Image Velocimetry ◽  
Liquid Spray ◽  
Cylinder Flow

An investigation of the interaction between the in-cylinder flow and the spray topology in two spray-guided direct injection optical engines is reported. The bulk flow field in the combustion chamber is characterized using particle image velocimetry. Geometrical parameters such as the axial penetration and the spray angle of the liquid spray are measured using Mie scatter imaging and/or diffuse back-illumination. The measured parameters are compared with data from a constant volume chamber available in the literature. For a late injection strategy, the so-called ECN Spray G standard condition, the mean values of the spray penetration do not seem to be significantly perturbed by the in-cylinder flow motion until the plumes approach the piston surface. However, spray probability maps reveal that cycle-to-cycle fluctuations of the spatial distribution of the liquid spray are affected by the magnitude of the in-cylinder flow. Particle image velocimetry during injection shows that the flow field in the vicinity of the spray plumes is heavily influenced by air entrainment, and that an upward flow in-between spray plumes develops. Consistent with previous research that demonstrated the importance of the latter flow structure for the prevention of spray collapse, it is found that increased in-cylinder flow magnitudes due to increased intake valve lifts or engine speeds enhance the spray-shape stability. Compared with cases without injection, the influence of the spray on the in-cylinder flow field is still noticeable approximately 2.5 ms after the start of injection.

Particle Image Velocimetry in a High-Pressure Turbine Stage at Aerodynamically Engine Representative Conditions

2020 ◽  
Author(s):  
Daniel Inman ◽  
David G. Cuadrado ◽  
Valeria Andreoli ◽  
Jordan Fisher ◽  
Guillermo Paniagua ◽  
...  
Keyword(s):  
High Pressure ◽  
Particle Image Velocimetry ◽  
Vector Fields ◽  
Particle Image ◽  
Flow Direction ◽  
Operating Conditions ◽  
Velocity Magnitude ◽  
Resultant Velocity ◽  
Image Velocimetry ◽  
Annular Cascade

Abstract Particle Image Velocimetry (PIV) is a well-established technique for determining the flow direction and velocity magnitude of complex flows. This paper presents a methodology for executing this non-intrusive measurement technique to study a scaled-up turbine vane geometry within an annular cascade at engine-relevant conditions. Custom optical tools such as laser delivery probes and imaging inserts were manufactured to mitigate the difficult optical access of the test section and perform planar PIV. With the use of a burst-mode Nd: YAG laser and Photron FASTCAM camera, the frame straddling technique is implemented to enable short time intervals for the collection of image pairs and velocity fields at 10 kHz. Furthermore, custom image processing tools were developed to optimize the contrast and intensity balance of each image pair to maximize particle number and uniformity, while removing scattering and background noise. The pre-processing strategies significantly improve the vector yield under challenging alignment, seeding, and illumination conditions. With the optical and software tools developed, planar PIV was conducted in the passage of a high-pressure stator row, at mid-span, in an annular cascade. Different Mach and Reynolds number operating conditions were achieved by modifying the temperature and mass flow. With careful spatial calibration, the resultant velocity vector fields are compared with Reynolds Averaged Navier Stokes (RANS) simulations of the vane passage with the same geometry and flow conditions. Uncertainty analysis of the experimental results is also presented and discussed, along with prospects for further improvements.

In Situ PLIF and Particle Image Velocimetry Measurements of the Primary Entrainment Fuel Jet in a Naturally Aspirated Water Heater

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Daniel J. Sherwin ◽  
Jon D. Koch
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Initial Conditions ◽  
Entrainment Rate ◽  
Water Heater ◽  
Cross Sectional ◽  
Mass Entrainment ◽  
Fuel Jet ◽  
Image Velocimetry ◽  
Entire Flow

The time-averaged characteristics of a fuel jet have been measured via acetone planar laser-induced fluorescence (PLIF) and particle image velocimetry (PIV) in the primary mixing region of an operating gas-fired water heater. These measurements allow for experimental characterization of the cross-sectional scalar and velocity fields as well as the estimation of the mass entrainment as the flow enters the burner in a practical system. In these experiments, reasonable results were obtained when only the fuel jet was seeded with acetone or PIV particles rather than the entire flow, thus demonstrating the potential for simplified experimental configurations in some applications where controlling or seeding the entire flow may be difficult. The entrainment characteristics of the fuel jet are compared with benchmarks from literature. The commercial device exhibits a larger mass entrainment rate than is found in typical free jets that have been studied in the literature. This may be a result of the jet's low Reynolds number (9,600) in comparison with other literature studies, and a result of initial conditions.

Experimental Characterization of Air-Entrainment in a Plunging Water Jet System Using Particle Image Velocimetry (PIV)

2010 ◽  
Author(s):  
Xiaoliang Qu ◽  
Afshin Goharzadeh ◽  
Lyes Khezzar ◽  
Arman Molki
Keyword(s):  
Particle Image Velocimetry ◽  
Free Surface ◽  
Particle Image ◽  
Air Entrainment ◽  
Water Jet ◽  
Experimental Characterization ◽  
Free Jet ◽  
Image Velocimetry ◽  
Plunging Water Jet

This paper presents a detailed experimental study of a plunging jet on a free liquid surface. An experimental characterization facility is designed and constructed for generating a vertical round water jet impinging on a free surface of a pool. The experimental analysis focuses on the jet penetration depth, its relation to impact velocity Vj and free jet length Lj. Present results are compared with previous studies. The flowmap for four different regimes, in terms of impact jet velocity is obtained. The details of the two-dimensional velocity field below the pool liquid free surface under a no-entrainment regime, is obtained using Particle Image Velocimetry (PIV) and reveals the entrainment behavior of the impinging jet flow below the interface.

AN IMPROVED ENTRAINMENT RATE MEASUREMENT METHOD FOR TRANSIENT JETS FROM 10 KHZ PARTICLE IMAGE VELOCIMETRY

2017 ◽  
Vol 27 (6) ◽  
pp. 531-557 ◽  
Author(s):  
W. Ethan Eagle ◽  
Mark P. B. Musculus ◽  
Louis Marie C. Malbec ◽  
Gilles Bruneaux
Keyword(s):  
Particle Image Velocimetry ◽  
Measurement Method ◽  
Particle Image ◽  
Entrainment Rate ◽  
Rate Measurement ◽  
Image Velocimetry
Sign in / Sign up

Export Citation Format

Share Document