Seismic tests of RC shear walls confined with high-strength rectangular spiral reinforcement

2017 ◽  
Vol 24 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Huajing Zhao ◽  
Qingning Li ◽  
Can Song ◽  
Haotian Jiang ◽  
Jun Zhao
Keyword(s):  
Shear Walls ◽  
High Strength ◽  
Seismic Tests

scholarly journals Steel Plate Cold-Rolled Section Steel Embedded High-Strength Concrete Low-Rise Shear Wall Seismic Performance

2018 ◽  
Vol 2018 ◽  
pp. 1-18
Author(s):  
Min Gan ◽  
Yu Yu ◽  
Liren Li ◽  
Xisheng Lu
Keyword(s):  
Bearing Capacity ◽  
Failure Mode ◽  
Seismic Performance ◽  
High Strength Concrete ◽  
Steel Plate ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Steel Plates ◽  
Strength Concrete

Four test pieces with different steel plate center-to-center distances and reinforcement ratios are subjected to low-cycle repeat quasistatic loading to optimize properties as failure mode, hysteretic curve, skeleton curve, energy dissipation parameters, strength parameters, and seismic performance of high-strength concrete low-rise shear walls. The embedded steel plates are shown to effectively restrict wall crack propagation, enhance the overall steel ratio, and improve the failure mode of the wall while reducing the degree of brittle failure. Under the same conditions, increasing the spacing between the steel plates in the steel plate concrete shear wall can effectively preserve the horizontal bearing capacity of the shear wall under an ultimate load. The embedded steel plates perform better than concealed bracing in delaying stiffness degeneration in the low-rise shear walls, thus safeguarding their long-term bearing capacity. The results presented here may provide a workable basis for shear wall design optimization.

scholarly journals Effect of Corrugation Angle and Direction on the Performance of Corrugated Steel Plate Shear Walls

2018 ◽  
Vol 4 (11) ◽  
pp. 2667
Author(s):  
Hayder Fadhil ◽  
Amer Ibrahim ◽  
Mohammed Mahmood
Keyword(s):  
Steel Plate ◽  
Low Cost ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Initial Stiffness ◽  
Construction Time ◽  
Element Analysis ◽  
Steel Plate Shear Wall ◽  
Steel Shear Wall

Corrugated steel plate shear wall (CSPSW) is one of the lateral resistance systems which consists mainly of steel frame (beam and column) with vertical or horizontal corrugated steel plate connected to the frame by weld, bolts or both. This type of steel shear wall characterized by low cost and short construction time with high strength, ductility, initial stiffness and excellent ability to dissipate energy. The aim of this paper is to evaluate the effect of corrugation angle and its direction on the performance of CSPSW under cyclic loading. The Finite element analysis was employed to achieve the research aim. The FE models were validated with experimental data available in the literature. Results reveal that the corrugation angle has a clear influence on initial stiffness, strength, ductility, and energy dissipation of CSPSW. The optimum performance of CSPSW can be obtained with angles of 30o for CSPSW with vertical corrugation and 20o for CSPSW with horizontal corrugation. The use of CSPSW with vertical corrugation provides higher strength, stiffness, and ductility compared to CSPSW with horizontal corrugation. Therefore, it is recommended to use CSPSW with vertical corrugation.

Behaviour of slender concrete shear walls with high-strength reinforcement under reversed cyclic loading.

2021 ◽  
Author(s):  
Nima Aghniaey ◽  
Murat Saatcioglu ◽  
Hassan Aoude
Keyword(s):  
Large Scale ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Analytical Investigation ◽  
Seismic Behaviour ◽  
Drift Capacity ◽  
Lateral Drift ◽  
Experimental Findings ◽  
Reversed Cyclic

Research on seismic behaviour of shear walls with high-strength steel is limited. A combined experimental and analytical investigation was conducted to assess seismic behaviour of flexure-dominant shear walls. A large-scale concrete shear wall with Grade 690 MPa (ASTM A1035) reinforcement and 84 MPa concrete was tested under simulated seismic loading. The wall was a ¼ -scale of a 6-storey shear wall, with 4.53 m height and 1.45 m length. It sustained a lateral drift of 1.8% prior to developing failure due to the rupturing of longitudinal reinforcement. This is 35% less than the drift capacity of a companion wall reinforced with 400 MPa reinforcement tested earlier. VecTor2 software was used to conduct an analytical parametric study to expand the experimental findings. The results indicate that the reinforcement grade has a significant impact on strength, ductility and hysteretic behaviour of shear walls.

Hysteretic Behavior of Composite Vertical Connection Structures used in Prefabricated Shear Wall Systems

2020 ◽  
Vol 20 (06) ◽  
pp. 2040007
Author(s):  
Limeng Zhu ◽  
Haipeng Yan ◽  
Po-Chien Hsiao ◽  
Jianhua Zhang
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
High Strength Steel ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Hysteretic Behavior ◽  
Design Standards

An innovative composite vertical connecting structure (CVC) with capacity carrying and energy-dissipating ability is proposed in this study, which could be used in prefabricated composite shear wall structural systems to enhance the resilience and seismic performance of structural system. The CVC structure is mainly composed of three parts, including the connecting zone, the capacity bearing zone characterized by high strength and elastic deforming ability, and the energy-dissipating zone assembled by replaceable metal dampers. The low-yield strength steel and high-strength steel are used, respectively, for the metal dampers in the energy-dissipating zone and the concrete-filled high-strength steel tubes in the bearing capacity zone to enhance the energy dissipation and self-centering abilities of CVC structures. The working mechanism is analyzed and validated through finite element models built in ABAQUS. The hysteretic behavior is simulated to evaluate their performance. First, the metal dampers are designed. The theoretical and finite elemental parametric analysis are carried out. According to the simulation results, the “Z-shaped” metal dampers exhibit better energy-dissipating ability than the rectangular shape, in which the “Z-shaped” metal dampers with 45∘ show the best performance. Simultaneously, the results of the models calculated by the finite element method and theoretical analysis work very well with each other. Furthermore, seven FE models of shear walls with CVC structures are designed. Monotonic and cyclic loading simulations are conducted. The failure modes and comprehensive mechanical performance are investigated and evaluated according to their calculated force–displacement curves, skeleton curves, and ductility coefficients. The results indicate that the CVC structure delivered preferable lateral-bearing capacity and displacement ductility. Finally, according to available design standards, the lateral stiffness of CVC structures could be conventionally controlled and some practical design recommendations are discussed.

Sign in / Sign up

Export Citation Format

Share Document