Suppression effect of film forming amine on flow accelerated corrosion of carbon steel in boiler feed water

2018 ◽  
Vol 2018.55 (0) ◽  
pp. K031
Author(s):  
Shota YAMAZAKI ◽  
Li-Bin NIU ◽  
Masaki YOSHIDA ◽  
Yusuke SUETAKE ◽  
Kazuo MARUGAME
Keyword(s):  
Carbon Steel ◽  
Feed Water ◽  
Accelerated Corrosion ◽  
Suppression Effect ◽  
Film Forming ◽  
Flow Accelerated Corrosion ◽  
Boiler Feed Water

scholarly journals Effect of Film Forming Amine on Flow Accelerated Corrosion of Carbon Steel in Boiler Feed Water of Power Plants

2019 ◽  
Vol 68 (4) ◽  
pp. 98-104
Author(s):  
Shota Yamazaki ◽  
Masaki Yoshida ◽  
Yusuke Suetake ◽  
Kazuo Marugame ◽  
Li-Bin Niu
Keyword(s):  
Carbon Steel ◽  
Power Plants ◽  
Feed Water ◽  
Accelerated Corrosion ◽  
Film Forming ◽  
Flow Accelerated Corrosion ◽  
Boiler Feed Water

Analytical Investigation of Deaerator Steam Inlet Nozzle Corrosion Allowance in a CANDU Station

2009 ◽  
Author(s):  
Ali Keshavarz ◽  
Andrew K. Ali ◽  
Randy K. Lall
Keyword(s):  
Finite Element ◽  
Carbon Steel ◽  
Stress Analysis ◽  
Analytical Investigation ◽  
Percentage Error ◽  
Metal Loss ◽  
Fe Model ◽  
Accelerated Corrosion ◽  
Materials Properties ◽  
Flow Accelerated Corrosion

Flow-accelerated corrosion (FAC) is a phenomenon that results in metal loss from piping, vessels and equipment made of carbon steel. This metal loss can lead to stress to occur at the steam inlet nozzle side, where it is located at the side of the deaerator. This paper presents a method to find the thickness critical of the steam inlet nozzle. A Finite Element (FE) model of the pressure vessel head was created to perform a stress analysis using NX Nastran 5.0. By applying materials properties, loads and constraints to the model, the results obtained are required to satisfy the following criterion: vonMises≥SySy=YieldStrength The results obtained from the stress analysis were analyzed to obtain a corrosion allowance and it was compared to the recommended value from a normal deaerator design, which is roughly 0.25 inches. From the FE model, and by continuously reducing the thickness of the nozzle, it was determined that the corrosion allowance is 0.229 inches, and that the percentage error was 8.4%.

Numerical Simulation of Turbulent Flow in Carbon Steel Pipes Leading to Flow Accelerated Corrosion

2014 ◽  
Vol 39 (8) ◽  
pp. 6435-6451 ◽  
Author(s):  
Rani Hari Ponnamma ◽  
Divya Teegala ◽  
Sahaya Ravi Ranjan ◽  
Vivekananda Kain ◽  
Barua Dipak Kumar
Keyword(s):  
Numerical Simulation ◽  
Carbon Steel ◽  
Turbulent Flow ◽  
Accelerated Corrosion ◽  
Steel Pipes ◽  
Flow Accelerated Corrosion

Flow accelerated corrosion of carbon steel feeder pipes from pressurized heavy water reactors

2012 ◽  
Vol 429 (1-3) ◽  
pp. 226-232 ◽  
Author(s):  
J.L. Singh ◽  
Umesh Kumar ◽  
N. Kumawat ◽  
Sunil Kumar ◽  
Vivekanand Kain ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Heavy Water ◽  
Accelerated Corrosion ◽  
Water Reactors ◽  
Flow Accelerated Corrosion

Prediction Model for Oxidation Layer Thickness in Flow Accelerated Corrosion

2014 ◽  
Author(s):  
Ruixuan Han ◽  
Yi Peng ◽  
Huailin Li
Keyword(s):  
Carbon Steel ◽  
Prediction Model ◽  
Flow Velocity ◽  
Layer Thickness ◽  
Balance Theory ◽  
Accelerated Corrosion ◽  
Oxidation Layer ◽  
Increasing Temperature ◽  
Flow Accelerated Corrosion ◽  
The Relationship

A new prediction model for the oxidation layer thickness of carbon steel is developed, that is based on the parabolic time law of corrosion and the mass transport balance theory. The relationship between the oxidation layer thickness and temperature, pH, and flow velocity is discussed. The predicted results show that the oxidation layer thickness increases exponentially with increasing temperature and decreases exponentially with increasing flow velocity. The oxidation layer thickness increases with increasing pH until pH=10.5 and then decreases. The predicted results agree with experimental results.

Sign in / Sign up

Export Citation Format

Share Document