Long Period Fiber Grating in Eccentric Core Single Mode Fiber

Author(s):  
Xiaofeng Xu ◽  
Xiaowei Ouyang ◽  
Ciming Zhou ◽  
Cui Zhang ◽  
Ai Zhou ◽  
...  
2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Marta Nespereira ◽  
João M. P. Coelho ◽  
Manuel Abreu ◽  
José Manuel Rebordão

Sensing performances of ultrashort (as low as 2.4 mm) long-period fiber gratings fabricated with CO2 laser radiation using commercial single mode fibers are presented. These lengths are, to our knowledge, the shortest of those found in the literature for this kind of sensors, approaching those typical in fiber Bragg gratings. Sensitivity to temperature and refractive index are demonstrated, with performances within the range expected for a single LPFG written on a single mode fiber without any enhancing technique. Analysis on results is made based on both theoretical and experimental data.


2020 ◽  
Vol 861 ◽  
pp. 259-263
Author(s):  
Ravivudh Khun-In ◽  
Yuji Usuda ◽  
Yuttapong Jiraraksopakun ◽  
Apichai Bhatranand ◽  
Hideki Yokoi

The rectangular-structured resin with one of its triangular long-period fiber grating surface is designed and printed out by using a high resolution 3D printer, so called long-period fiber grating (LPFG) resin. This LPFG resin is directly pressed on the bare single-mode fiber by a digital force meter to filter out partial band of light inside the fiber. The grating period is expanded by tilting the resin from the initial fiber axis. The optical filter is observed as resonant wavelengths from the broadband wavelength. The results show that the resonant wavelength shift is a linear function of the grating period with the coefficient of determination over 0.99. The proposed scheme has a great potential to be employed as a sensor such as a selective optical filter and a buried intrusion sensor.


2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Marta Nespereira ◽  
João M. P. Coelho ◽  
José Manuel Rebordão

The response of ultrashort-length CO2-induced long-period fiber grating (LPFG) sensors to torsion is reported. While engraving using CO2 laser radiation, the fiber is submitted to high tension allowing the obtainment of gratings with shorter lengths, down to 2.4 mm, which is almost one order of magnitude lower than the usual. Also, the fiber is only irradiated in one side, creating an asymmetrical profile leading to highly birefringent gratings. Sensitivity to axial twists is demonstrated, with values up to 0.15 nm/(rad/m) for the resonant wavelength shift and higher than 0.03 dBm/(rad/m) for the variation in the intensity (attenuation). Discrimination between rotation directions, clockwise and counterclockwise, was observed.


2021 ◽  
Vol 51 (3) ◽  
Author(s):  
Yunfeng Bai ◽  
Zelong He ◽  
Jiyuan Bai ◽  
Suihu Dang

The single-mode fiber provided by YOFC inc is employed for spiral processing by commercial welding machine. It can clearly see the periods structure under the light, but there is no obvious deformation of the fiber core, cladding and surface morphology under a microscope. There is an obvious resonant peak near 1560 nm, half peak width is about 25 nm, the depth of the resonant peak closed to –26 dB, when the period is about 411 μm. It agrees with theoretical calculation results according to the long-period fiber grating coupled-mode theory. The resonance wavelength is caused by coupling between the fundamental mode and the LP14 mode. The responsivities of the helically twisted long-period fiber gratings (H-LPFG) for the temperature is measured, the resonance wavelength is linear with temperature, the slope is 86 pm/℃. Because it is easy to inscribe by commercial welding machine, and has a strong resonance peak, it has potential applications as the temperature sensor.


Sign in / Sign up

Export Citation Format

Share Document