High Speed Passive Optical Network Based Elastic Optical Communication System

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
Nikhlesh Kumar Mishra ◽  
Kamal Kishore Upadhyay ◽  
N. K. Shukla
Keyword(s):  
Optical Networks ◽  
Communication System ◽  
High Speed ◽  
Optical Network ◽  
Wave Length ◽  
Single Mode ◽  
Passive Optical Network ◽  
High Data ◽  
Data Rates ◽  
Communication Needs

AbstractFor addressing needs of modern day communication needs, new type of networks are required to be evolved to cater the demand of high data rates. Use of survivable elastic-optical-network (EON) with existing passive-optical-networks (PON) may provide the solution for this. The present work focus on employing EON–PON based wave-length-division multiplexing enabled communication system comprises of 2×5 Gbps for downlink and 2×1 Gbps for uplink over a single-mode-fibre of length 100 km. The results are the evaluated via bit-error-rate analyser, q factor and eye diagrams.

An ultra-dense spacing-based PON by incorporating dual drive Mach–Zehnder modulator for comb generation

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Navjot Singh ◽  
Bharat Naresh Bansal
Keyword(s):  
Optical Networks ◽  
High Speed ◽  
Low Cost ◽  
Optical Network ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Passive Optical Network ◽  
Passive Optical Networks ◽  
Differential Phase Shift ◽  
High Data

Abstract Wavelength division multiplexed passive optical is promising technique to achieve a high data rate and large number of user. The notable advantages of WDM PON is the combination of reliability, cheap in cost, accessible bandwidth, high security, large optical reach and it can support large number of ONU. There are multiple approaches to achieve high-speed WDN PON using different transmission techniques. In WDM, multiple lasers are required which increase the cost of the system. To reduce cost, an optical multicarrier generation system is proposed. An economical multiple carrier generation with the incorporation of sine generator and Mach–Zehndar modulator is demonstrated. Utmost work of sine generator and dual drive modulator was to attain low cost functioning of passive optical networks. Multicarrier generation was done and replacement of laser carriers with optical multicarrier generator. Carriers were generated with the frequency spacing of 20 GHz and these carriers were used in the passive optical networks with the tone-to-noise ratio of 40 dB, amplitude difference of 1.4 dB. For the transmission of downstream in the PON, differential phase shift keying was employed at 10 Gbps data speed. Transmission distance achieved was 30 km using single-mode fiber and this was a part of optical distribution network. Optical network unit was next part after ODN and signals were received with balanced receiver. Moreover, half signal was given to intensity modulator for the signal re-modulation. Bit error rate of 10–9 was achieved at all channels in the downstream. An upstream of 10 Gbps was accomplished in the passive optical network.

scholarly journals An overview of passive optical networks and components

2021 ◽  
Author(s):  
Kanchan Bala
Keyword(s):  
Optical Networks ◽  
High Speed ◽  
Optical Network ◽  
Access Network ◽  
Single Mode ◽  
Telecommunication Networks ◽  
Passive Optical Network ◽  
Passive Optical Networks ◽  
Optical Access ◽  
Last Mile

Over the past few years, telecommunication networks have experienced a dramatic shift from traditional voice-dominated traffic to data-oriented, application-based traffic. The access network or the last-mile connecting households or businesses to the internet backbone, have been recognized as a major bottleneck in todays network hierarchy. The ongoing demand for new access networks that support high-speed (greater than 100 Mb/s), symmetric, and guaranteed bandwidths for future video services has been accelerated and the search for a cost-effective optical access solution has yielded a number of possible solutions. To satisfy the required bandwidth over a 20-km transmission distance, single-mode optical fiber is a natural choice. Passive Optical Networks (PONs) are promising access solutions that will open the last-mile bottleneck bringing data rates of 100 Mb/s to 1 Gb/s to the end-users. The goal of this work is to provide a cohesive overview of research done in the area of Fiber In The Loop (FITL) optical access technology. Specifically, it explores the area of Passive Optical Network (PON) : its history, variants, architecture, and standards. Various passive optical components which make a passive optical network work, are also discussed. Some laboratory emulations on RF over PON showing noise, distortion, and fading in the channels are then carried on using the Vector Signal Generator SMIQ03B (Rhode & Schwarz), and the Wireless Communication Analyzer WCA380 (SONY Tektronix).

scholarly journals An overview of passive optical networks and components

2021 ◽  
Author(s):  
Kanchan Bala
Keyword(s):  
Optical Networks ◽  
High Speed ◽  
Optical Network ◽  
Access Network ◽  
Single Mode ◽  
Telecommunication Networks ◽  
Passive Optical Network ◽  
Passive Optical Networks ◽  
Optical Access ◽  
Last Mile

Over the past few years, telecommunication networks have experienced a dramatic shift from traditional voice-dominated traffic to data-oriented, application-based traffic. The access network or the last-mile connecting households or businesses to the internet backbone, have been recognized as a major bottleneck in todays network hierarchy. The ongoing demand for new access networks that support high-speed (greater than 100 Mb/s), symmetric, and guaranteed bandwidths for future video services has been accelerated and the search for a cost-effective optical access solution has yielded a number of possible solutions. To satisfy the required bandwidth over a 20-km transmission distance, single-mode optical fiber is a natural choice. Passive Optical Networks (PONs) are promising access solutions that will open the last-mile bottleneck bringing data rates of 100 Mb/s to 1 Gb/s to the end-users. The goal of this work is to provide a cohesive overview of research done in the area of Fiber In The Loop (FITL) optical access technology. Specifically, it explores the area of Passive Optical Network (PON) : its history, variants, architecture, and standards. Various passive optical components which make a passive optical network work, are also discussed. Some laboratory emulations on RF over PON showing noise, distortion, and fading in the channels are then carried on using the Vector Signal Generator SMIQ03B (Rhode & Schwarz), and the Wireless Communication Analyzer WCA380 (SONY Tektronix).

Electrical Spreading Code-Based OFDM Optical Access Networks for Budget Enhancement and Reduced System Bandwidth Requirement

2015 ◽  
Vol 36 (4) ◽  
Author(s):  
Pravindra Kumar ◽  
Anand Srivastava
Keyword(s):  
Optical Networks ◽  
Orthogonal Frequency Division Multiplexing ◽  
High Speed ◽  
Optical Network ◽  
Access Networks ◽  
Passive Optical Network ◽  
Spreading Code ◽  
Optical Access Networks ◽  
Optical Access ◽  
Code Division Multiple

AbstractPassive optical networks based on orthogonal frequency division multiplexing (OFDM-PON) give better performance in high-speed optical access networks. For further improvement in performance, a new architecture of OFDM-PON based on spreading code in electrical domain is proposed and analytically analyzed in this paper. This approach is referred as hybrid multi-carrier code division multiple access-passive optical network (MC-CDMA-PON). Analytical results show that at bit error rate (BER) of 10

An Integrated High-Speed Full Duplex Coherent OFDM-PON and Visible-Light Communication System

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
Simarpreet Kaur ◽  
Mahendra Kumar ◽  
Ashu Verma
Keyword(s):  
Visible Light ◽  
Optical Networks ◽  
High Speed ◽  
Light Emitting Diode ◽  
Low Cost ◽  
Dispersion Compensation ◽  
Optical Network ◽  
Visible Light Communication ◽  
Passive Optical Network ◽  
Full Duplex

AbstractWe demonstrated a full duplex hybrid passive optical network and indoor optical wireless system employing coherent optical frequency division multiplexing. To accomplish reliable transmission in passive optical networks integrated visible-light communication (VLC), yellow light-emitting diode and infrared LED is used in downstream and upstream, respectively, for intra building network. In order to support high data rate, pulse-width reduction scheme based on dispersion compensation fiber is incorporated and system successfully covered the distance of 50 km. A data stream at the rate of 30 Gb/s is transmitted for each user out of eight users. VLC-supported users are catered with the bit rate of 1.87 Gb/s over 150 cm and in order to realize a low-cost system, visible and infrared LEDs are used in downlink and uplink, respectively.

Research on Power Optimization Based on Adaptive Passive Optical Networks

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Li Li ◽  
Li Hong-Jie
Keyword(s):  
Optical Networks ◽  
Optical Network ◽  
Access Network ◽  
Data Rate ◽  
Passive Optical Network ◽  
High Data Rate ◽  
Transmission Power ◽  
High Data ◽  
Maximum Transmission ◽  
Wdm Pon

AbstractFor the commercial wavelength division multiplexing passive optical network (WDM-PON) with standard single-mode fiber SSMF-28 and 1:64 passive fiber branching at its far end (RN) and 100 GHz C-band continuous wavelength (CW) lasers, the maximum coverage and optimal transmission power of STM-16 and STM-64 with external modulators at different speeds and wave numbers (4λ, 8λ and 16λ) are obtained, respectively. The performance parameter of the high data rate WDM-PON system is analyzed with respect to a number of channels and reach. In order to improve the network utilization and receiving efficiency, the influence of different channels and transmission distances on the performance of high data rate WDM-PON system is analyzed. Simulation analysis with Optisystem15.0. The maximum transmission power required to achieve the maximum transmission distance under the condition of nonlinear constraints is obtained. In order to save power consumption, the configuration of each multi-band PON is optimized in terms of transmission power. It is found that WDM-PON system has to compromise between aggregated data rate and system reach. Future software defined access network reconfigure the access network depending on the dynamic demand and the resources available. Hence depending on the distance between the optical line terminal (OLT) and optical network unit (ONU) guaranteed data rate can be estimated. ONU is equipped with a tunable optical filter (TOF) hence future wavelength can be reconfigured by both service provider and user. It makes it possible for software to customize optical access network.

scholarly journals Multi-Twin-SSB Modulation with Direct Detection Based on Kramers–Kronig Scheme for Long-Reach PON Downstream

2019 ◽  
Vol 9 (4) ◽  
pp. 748 ◽  
Author(s):  
Xiang Gao ◽  
Yuancheng Cai ◽  
Bo Xu ◽  
Xiaoling Zhang ◽  
Kun Qiu
Keyword(s):  
Optical Networks ◽  
Forward Error Correction ◽  
Direct Detection ◽  
Chromatic Dispersion ◽  
Optical Network ◽  
Single Mode ◽  
System Optimization ◽  
Single Mode Fiber ◽  
High Data ◽  
Multi Band

As the demand for high data volumes keeps increasing in optical access networks, transmission capacities and distance are becoming bottlenecks for passive optical networks (PONs). To solve this problem, a novel scheme based on multi-twin single sideband (SSB) modulation with direct detection is proposed and investigated in this paper. At the central office, two SSB signals are generated simultaneously with the same digital-to-analog converters (DACs). The twin-SSB signal is not only robust against frequency selected power fading introduced by chromatic dispersion (CD), but also improves the spectral efficiency (SE). By combining a twin-SSB technique with multi-band carrier-less amplitude/phase modulation (multi-CAP), different optical network units (ONUs) can be supported by flexible multi-band allocation based on software-reconfigurable optical transceivers. The Kramers–Kronig (KK) scheme is adopted on the ONU side to effectively mitigate the signal–signal beat interference (SSBI) induced by the square-law detection. The proposed system is extensively studied and validated with four sub-bands using 50 Gbps 16 quadrature amplitude modulation (QAM) modulation for each sub-band using numerical simulations. Digital pre-equalization is introduced at the transmitter-side to balance the performance of different ONUs. After system optimization, a bit error rate (BER) threshold for hard decision forward error correction (HD-FEC) code with 7% redundancy ratio (BER = 3.8 × 10−3) can be reached for all ONUs over 50-km standard single-mode fiber.

20 Gbps Bidirectional Transmission via Four Channels over Long-haul SMF in a WDM-PON Architecture using External Modulation Scheme

2017 ◽  
Vol 38 (2) ◽  
Author(s):  
Anindya Sundar Das ◽  
Ardhendu Sekhar Patra
Keyword(s):  
Optical Network ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Passive Optical Network ◽  
Modulation Scheme ◽  
Wavelength Division ◽  
Wavelength Division Multiplexed ◽  
External Modulation ◽  
Data Rates ◽  
High Bandwidth

AbstractA novel architecture of bidirectional gigabit signal transport system over long-haul single-mode fiber (SMF) using wavelength division multiplexed passive optical network technique is proposed and demonstrated. In order to offer multimedia services of high bandwidth, four signals of 5 Gbps data rates are externally modulated and transmitted through four channels over 100-km SMF in uplink and downlink. In our proposed scheme, an excellent bit error rate, good

scholarly journals Polarization Division Multiplexing of OFDM Radio-over-Fiber Signals in Passive Optical Networks

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Maria Morant ◽  
Joaquin Pérez ◽  
Roberto Llorente
Keyword(s):  
Optical Networks ◽  
Spectral Efficiency ◽  
Optical Network ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Radio Over Fiber ◽  
Passive Optical Network ◽  
Passive Optical Networks ◽  
The Impact ◽  
Polarization Division Multiplexing

This paper describes the state-of-the-art of polarization multiplexing for optical networks transmission. The use of polarization division multiplexing (PDM) permits to multiply the user capacity and increase the spectral efficiency. Combining PDM and orthogonal frequency division multiplexed (OFDM) modulation allows maximizing the optical transmission capacity. The experimental demonstration of transmitting OFDM signals following ECMA-368 ultrawide band (UWB) standard in radio-over-fiber using PDM in passive optical networks is herein reported. The impact of cross-polarization and cochannel crosstalk is evaluated experimentally in a three-user OFDM-UWB subcarrier multiplexed (SCM) configuration per polarization. Each SCM uses up to three OFDM-UWB channels of 200 Mbit/s each, achieving an aggregated bitrate of 1.2 Gbit/s with 0.76 bit/s/Hz spectral efficiency when using PDM transmission. The experimental results for the polarization-multiplexed SCM indicate that a 4 dB additional polarization crosstalk interference can be expected compared to a nonpolarization-multiplexed transmission system which translates to 2.4 dB EVM penalty in the UWB signals. The successful PDM transmission of SCM multiuser OFDM-UWB over a passive optical network of 25 km standard-single mode fiber (SSMF) reach is demonstrated.

Radio over fiber on gigabit passive optical network using QPSK modulation scheme

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Thandapani Kavitha ◽  
Arokiam Arulmary ◽  
Pandian Nagarajan
Keyword(s):  
Optical Networks ◽  
Network Architecture ◽  
Optical Network ◽  
Wave Length ◽  
Optical Signal ◽  
Simulation Software ◽  
Radio Over Fiber ◽  
Passive Optical Network ◽  
Modulation Scheme ◽  
Eye Diagram

AbstractHybrid gigabit-passive optical network (GPON) is one of the hybrid optical networks, it integrates both Wave length Division Multiplexing (WDM) GPON and Time Division Multiplexing (TDM) GPON into a single passive network, which lowers the energy consumption, networking expenditure and boosts the data rate. In this paper, Radio over Fiber Technique of 10 GB/s GPON network architecture is implemented and verified using Quadrature Phase Shift Keying Modulation of 2.4 GHz radio frequency. Single-mode fiber of length 50 km is used to propagate the radio signals. Commercial OptiSystem simulation software is used to simulate the model. In total, 32 and 64 users are supported through this model. Based on the response of the constellation diagram, received power, eye diagram, and optical signal-to-noise ratio, the system is analyzed.

Sign in / Sign up

Export Citation Format

Share Document