scholarly journals Theoretical Analysis of the Rectangular Defect Orientation using Magnetic Flux Leakage

2018 ◽  
Vol 18 (1) ◽  
pp. 28-34
Author(s):  
J. Sam Alaric ◽  
V. Suresh ◽  
A. Abudhahir ◽  
M. Carmel Sobia ◽  
M. Baarkavi
Keyword(s):  
Magnetic Flux ◽  
Analytical Model ◽  
Three Dimensional ◽  
Tangential Component ◽  
Magnetic Flux Leakage ◽  
Axial Component ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Flux Leakage

Abstract This paper presents an approach to estimate the orientation of the rectangular defect in the ferromagnetic specimen using the magnetic flux leakage technique. Three components of the magnetic flux leakage profile, such as radial, axial, and tangential component are considered to estimate the orientation of the rectangular defect. The orientation of the rectangular defect is estimated by the proposed analytical model using MATLAB software. The results calculated by the analytical model are validated by the three-dimensional finite element analysis using COMSOL Multiphysics software. Tangential component provides better performance to estimate the orientation of the rectangular defect compared with radial and axial component of the magnetic flux leakage profile.

3D Finite Element Analysis for Magnetic Flux Leakage Testing

2011 ◽  
Vol 201-203 ◽  
pp. 1623-1626
Author(s):  
Qiang Song
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Magnetic Flux ◽  
Three Dimensional ◽  
Magnetic Flux Leakage ◽  
Destructive Testing ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Flux Leakage

Magnetic flux leakage (MFL) is a non-destructive testing method used to inspect ferrous materials. However, apparatus parameters could affect the MFL inspection tool’s ability to characterize anomalies. In this paper, MFL signals obtained during the inspection of pipes have been simulated using three-dimensional finite element analysis and the effects of magnet assembly on MFL signals are investigated. According to numerical simulations, an increase in the leakage flux amplitude is observed with an increase in the permanent magnet size and the inflexion point may indicate the presence of magnetizing pipe wall to near saturation. It clearly illustrates degradation in the MFL with increasing backing iron length. The relationship between MFL apparatus parameters and MFL signals could be utilized in the MFL technique to characterize the defect.

Analytical model for a superelastic Timoshenko shape memory alloy beam subjected to a loading–unloading cycle

2018 ◽  
Vol 29 (20) ◽  
pp. 3902-3922 ◽  
Author(s):  
Nguyen Van Viet ◽  
Wael Zaki ◽  
Rehan Umer
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Analytical Model ◽  
Solid Phase ◽  
Three Dimensional ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

We propose a new analytical model for a superelastic shape memory alloy prismatic cantilever beam subjected to a concentrated force at the tip. The force is gradually increased and then removed and the corresponding distribution of phase transformation fields in the beam is determined, analytically, in both the transverse and longitudinal directions. Analytical moment–curvature and shear force–shear strain relations are also derived during loading and unloading of the beam. The proposed model is validated against an exact numerical beam model as well as a three-dimensional finite element analysis model for the same beam, with very good agreement in each case. Moreover, an experiment is proposed and carried out to characterize the load–deflection response of a shape memory alloy beam under the same boundary conditions as those considered in deriving the model. The obtained response is in good agreement with the analytical model as well as three-dimensional finite element analysis simulations. The analytical method provides a direct mathematical way for describing the material and structural properties of the beam and the distribution of the different solid phase regions as they change under the influence of an applied load and allows the determination of details such as the boundaries of solid phase regions immediately and accurately using equations. The same would require postprocessing at possibly significant computational cost and personal effort if finite element analysis or similar numerical methods are used.

Numerical Simulation and Analysis on Magnetizing Exciter for Magnetic Flux Leakage

2011 ◽  
Vol 474-476 ◽  
pp. 1187-1190
Author(s):  
Qiang Song
Keyword(s):  
Magnetic Flux ◽  
Permanent Magnet ◽  
Flux Density ◽  
Pipe Wall ◽  
Three Dimensional ◽  
Magnetic Flux Leakage ◽  
Magnetic Flux Density ◽  
Outer Diameter ◽  
Element Analysis ◽  
Flux Leakage

Magnetic flux leakage (MFL) is a non-destructive testing method used to inspect the pipe and magnetization of the pipe wall to saturation is essential for anomalies to be reliably and accurately detected and characterized. Axial components of magnetic flux density obtained during the MFL inspection have been simulated using three-dimensional finite element analysis and the effects of magnetizing exciter parameters on magnetic flux density are investigated. The pipe modeled in this paper has an outer diameter of 127mm (5 in.) with a wall thickness of 9 mm (0.354 in.). According to numerical simulations, an increase in the magnetic flux density of pipe wall is observed with an increase in the permanent magnet length and height. It clearly illustrates that Nd-Fe-B permanent magnet assembly with 70 mm length and 40 mm height may magnetize pipe wall to near saturation.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Sign in / Sign up

Export Citation Format

Share Document